低温高速离心泵的研制与应用

阐述了适合于输送低温介质的高速离心泵的水力设计和结构设计方法，结构上采有长，中，短叶片相间的复合叶轮及双密封结构，理论上采用以效率为目标函数的优化水力设计方法，保证了低温高速离心泵具有很好的工人可靠性和优越的性能指标。     

纳米级BaAl_2O_4微粉的制备和性质

分别用溶胶 -凝胶法、低温固相反应法 ,制得了纳米级BaAl2 O4微粉 ,用电镜观察了其形貌和粒径的大小 ,用X-射线衍射仪进行了物相分析 ,测定了其纯度与晶型 ,讨论了制备方法与粒度大小的相互影响     

Application of annexation principle of thermodynamic property of In-Pb-Sb and In-Bi-Pb melts

Based on the principle of annexation and phase diagrams, the structural units of In-Pb-Sb and In-Bi-Pb melts were determined, and their calculating models of mass action concentrations were formulated. Calculated results agree well with practical values, which in turn show that the models deduced can reflect the structural realities of corresponding melts and the principle of annexation is applicable not only to some binary metallic melts, but also to ternary metallic melts.     

测定钠中杂质的手动阻塞计的研究

文章介绍了测定钠中杂质浓度的手动阻塞计的原理、装置和实验结果。为了减少测量误差,我们研究了影响准确测定阻塞温度的因素,并且找到了减少测量误差的办法。在同样的杂质饱和温度下,该阻塞计测得的高、低阻塞温度所对应的杂质浓度差是很接近的。对氧其差值为1.03ppm;对氢为0.0763ppm。     

含氯取代基的聚间苯二甲酰间苯二胺的合成与表征

以 2 ,5 -二氯对苯二甲酰氯作为第三单体 ,将其与间苯二甲酰氯、间苯二胺在N ,N -二甲基乙酰胺中进行低温溶液共缩聚反应 ,合成了含氯取代基的聚间苯二甲酰间苯二胺。研究了单体摩尔浓度、反应初始温度、叔胺添加剂种类、第三单体用量等对共聚物相对分子质量的影响 ,并用红外光谱、热重分析等方法对共聚物进行了表征。     

多输入单输出逆高斯分布流域汇流模型

本文将逆高斯分布应用于由水库和区间组成的复杂的流域汇流系统，并建立了多输入单输出逆高斯单位线模型。讨论了模型参数的估计方法，并对沾益流域的雨洪资料进行了实例分析。     

大港白水头地区低阻油气层测井评价

在对白水头地区低阻油层的地质特征、物性特征及成因环境进行了分析研究后 ,应用测井曲线特征集法 ,把白水头油田常规油气层、低阻油气层、油水同层、水层等看成是独立的地质事件 ,建立了它们与测井曲线特征之间的对应关系 ,利用这种关系对未知地质事件进行了预测划分。最后根据所建模型定量计算储层各种参数 ,收到了良好的地质效果 ,表明测井曲线特征集法对于识别多成因的低阻油层是一种有效方法     

Immobilization and activation of vanadium(III) and titanium(III) single‐site catalysts for ethylene polymerization using MgCl2‐based supports

Significant increases in the activity of vanadium(III) amidinate catalysts for ethylene polymerization have been obtained by immobilization on a MgCl₂‐based support prepared by reaction of AlEt₃ with a MgCl₂/ethanol adduct. Catalyst immobilization and activation on this type of support prevents the rapid decay in activity observed under homogeneous polymerization conditions with unsupported catalysts. Stable polymerization activity is also observed with analogous titanium(III) complexes. Polyethylene with narrow molecular weight distribution and spherical particle morphology is obtained without reactor fouling. Copyright © 2005 Society of Chemical Industry     

Low density polyethylene and grafted lignin polyblends using epoxy‐functionalized compatibilizer: mechanical and thermal properties

Lignin was graft copolymerized with methyl methacrylate using manganic pyrophosphate as initiator. This modified lignin was then blended (up to 50 wt%) with low density polyethylene (LDPE) using a small quantity of poly[ethylene‐co‐(glycidyl methacrylate)] (PEGMA) compatibilizer. The mechanical properties of the blend were substantially improved by using modified lignin in contrast to untreated lignin. Differential scanning calorimetry studies showed loss of crystallinity of the LDPE phase owing to the interaction between the blend components. Thermogravimetric analysis showed higher thermal stability of modified lignin in the domain of blend processing. This suggested that there is scope for useful utilization of lignin, which could also lead to the development of eco‐friendly products. Copyright © 2005 Society of Chemical Industry     

氨氮监测中样品蒸馏预处理对结果的影响分析

氨氮监测采用预蒸馏处理后，比色测定结果明显偏低。在样品预蒸馏处理过程中，硼酸作为吸收液，使显色时溶液pH值偏低，导致显色不充分是其主要影响因素。通过采取增加显色剂加入量的方法，解决了显色pH值偏低的问题，得到满意的测定结果。