高坝通航技术在水口工程的新发展

水口水电站坝高101m,航运过坝采用一线三级船闸和一线垂直升船机。水口升船机是当时国内已建和在建同类升船机中总体规模最大的升船机,也是我国第一座自行设计、制造、施工和安装的大型升船机。在塔楼结构动力分析和试验研究、塔楼滑框倒模施工、升船机整体模型试验研究、承船厢整体制造和浮运、船厢安全锁定装置和船厢对接密封装置试验研究、整机安装及联调试验等方面充分体现了水口升船机的建成是高坝通航技术的新发展。     

射频电缆组件组装工艺浅谈

近年来国内外射频电缆组件的发展很快,射频电缆组件的性能不断提高,对射频电缆组件组装工艺也提出了更高的要求.射频电缆组件组装过程多是手工操作,产品的一致性及性能很难控制,要求有良好的工艺保证,为此介绍了射频电缆组件组装工艺,包括电缆的裁剪及剥皮、内导体的连接、外导体的连接和电气性能的测试;探讨了在组装过程中应注意的问题,以及针对内导体焊接易出现虚焊问题进行研究.     

A Relational Model of Workplace Victimization: Social Roles and Patterns of Victimization in Dyadic Relationships.

This article proposes a model of the ways in which dyadic interactions between employees who occupy 1 of 4 archetypal social roles in organizations can lead to either episodic or institutionalized patterns of victimization. The model shows how the occurrence of victimization involving these 4 role types is influenced by organizational variables such as power differences, culture, and access to social capital. The model integrates behavioral and social structural antecedents of victimization to develop a relational perspective on the dynamics of harmful behavior in the workplace. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

CFH-Ⅱ型翻车机传动齿轮轴承座的座脚螺栓联接失效分析与改进

分析了CFH-Ⅱ型翻车机传动齿轮轴承座的座脚螺栓组联接失效(松动)的原因，得出控制和保证合适的螺栓组联接预紧力是防止螺栓联接失效(松动)的关键；依据现场条件，对座脚螺栓进行了设计改进；提出了一种适合现场使用的螺栓预热伸长的装配方法，经实践验证此法是简单可靠的装配方法。     

二氧化锡溅射工艺研究

SnO2 是最早使用也是目前使用最广泛的一种气敏材料 ,使用该材料设计制作的气敏传感器具有许多优点。在简要介绍溅射镀膜的成膜过程和特点的基础上 ,着重介绍了SnO2 膜的制备流程 ,分析了功率和温度变化对成膜质量的影响     

天然气井井筒及井口安全技术研究

天然气勘探开发具有高温、高压、高风险,安全技术及管理难度大等特点,通过实例分析天然气井存在的主要问题,提出应采取的关键安全技术及需要解决的问题。     

用于高频谐振器的PbTiO_3基压电陶瓷

传统的PZT压电陶瓷的相对介电常数较大,一般为1 000以上,用于高频谐振器不易与线路匹配;而PbTiO3基压电陶瓷的相对介电常数较小,一般仅为200左右,对于10 MHz以上频率的谐振器,用PbTiO3基压电陶瓷作为压电振子是最佳的选择。本文主要研究用于高频谐振器的MnO2和Nd2O3改性PbTiO3基压电陶瓷的性质。PbTiO3基压电陶瓷的性质的改善是与此种陶瓷的制备工艺,显微结构和电导机制紧密相关的。     

加强企业科技管理与提高经济效益

本文阐述了加强科技管理的意义,针对包钢近年来科技管理工作的加强提出了一些改进意见和建议,同时进一步论述了加强科技管理对提高企业经济效益的作用.     

经济实用的DSP电源解决方案

笔者介绍了两种低纹波的DSP电源解决方案:一为采用MAX1793和大电流EMI静噪滤波器NFM41P;二为改进的去耦p型滤波电路和大电流EMI静噪滤波器NFM41P。并对方案的特点及其实现进行了详细的解析。试验结果表明:所述方案的纹波小,仅100 mV左右;成本低,仅几十元;适用范围广,通过改变MAX1793芯片的输出电压,可将本方案移植到TI的C5000,C6000系列,且还可用于其他的脱机工作系统。     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.