On‐Line Detection Of State‐Of‐Charge In Lead Acid Battery Using Radial Basis Function Neural Network

To realize a stable supply of electric power in an automobile, an accurate and reliable detection method of SOC (state‐of‐charge) in a lead acid battery is required. However the dynamics of the battery is very complicated. The characteristics of the battery greatly change due to its degradation. Moreover a automobile has many driving patterns, which are unknown beforehand. Thus it is not easy to detect the SOC analytically. In this paper, to overcome this problem, a new on‐line SOC detection method with a radial basis function neural network is proposed. In order to increase the detection accuracy of degraded batteries, physical values related to the degradation degree are used as input signal in the neural network. The detection accuracies for different sized batteries and various degradation states are investigated.     

某跨线桥施工支架方案设计

结合某大桥的概况,根据梁体施工工艺要求、现场实地勘察情况确定跨线施工方案,支架采用布架灵活、搭拆方便、承载力大的WDJ碗扣式多功能钢支架,部分预应力现浇连续箱梁采用支墩加纵梁预留门洞的支架现浇,取得良好效果。     

台式毛细管放电X光激光装置调试实验

对自行研制的台式毛细管放电X光激光装置进行了系统调试,在充氩气毛细管负载下,输出电流38kA,电流脉冲前沿40ns,并对有关问题进行了讨论.并在这个装置上开展充氩气毛细管放电荧光光谱实验研究.     

串扰耦合的低频分析有效性及阻抗特性研究

从传输线模型出发，分析了二平行直导线间串扰的低频模型有效性，得出允许3dB误差的条件下，低频模型在工程计算串扰中的电学短线和频率足够小的具体限值；同时分析了端接阻抗大小对串扰耦合的影响。对电磁兼容性中的串扰耦合的工程应用有实际指导和参考意义。     

Effects of calcination temperature on phase and microstructure evolution of BaTi4O9 powders

Calcining of the mixture of BaCO₃ and TiO₂ with a ratio 1:4 at different temperatures was carried out to synthesize BaTi₄O₉ powders. Phase evolution of the samples was studied using the differential thermal analysis (DTA) and X-ray diffractometry (XRD). Both techniques confirmed that the formation of BaTi₄O₉ started around 1000 °C. The XRD peaks showed that BaTi₄O₉ was most pronounced at 1250 °C. X-ray line broadening methods were employed to study the variation of particle size and microstrain of the BaTi₄O₉ powders. The Voigt function in a single line and the pseudo-Voigt function in the variance methods were used in our case. We found that both functions resulted in the same trends, i.e., the particle size increased with the temperature with the biggest size of 180 and 160 nm, whilst the microstrain yielded the opposite trend with the lowest values of 6.2 × 10^–3 and 1.1 × 10^–3. The scanning electron microscopy (SEM) study revealed the size of the large particles formed, due to agglomeration, to be about 0.5–1.9 μm. Furthermore, it was shown that irregular shapes of BaTi₄O₉ powders necked to each other appeared at 1000 °C and grew into ellipse and rod shapes at 1250 °C. Electronic Publication     

光纤专用网中基于DSP的Q值在线检测模块的设计

基于误码率与Q值的对应关系，本文介绍一种Q值在线检测方法，模块设计采用DSP技术，并讨论了该模块在光纤工业专用网（FIN）中的应用。     

射频MEMS压控电容器

研究了射频 MEMS压控电容器的设计和制造工艺。压控电容器的制作采用了 MEMS制造技术 ,其主要结构为硅衬底上制作金属传输线电极和介质层 ,然后制作金属膜桥作为电容器的另一个电极。通过改变加在金属膜桥与传输线间的电压达到改变电容值的目的。这种压控电容器可以工作于射频和微波波段 ,具有很高的Q值。测试结果如下 :在 1 GHz、0 V时 Q值达到 3 0 0 ,0偏压电容值为 0 .2 1 p F,当加上驱动电压后 Cmax/ Cmin的变比约为 4∶ 1     

城市燃气管网设计若干问题的探讨

分析了哈依燃气管道工程在施工及管理过程中存在的问题，并就如何解决这些问题提出了建议。     

计算机辅助设计中浓淡曲线的设计

本文介绍利用Super Frame软件进行色彩浓淡设计的原理、方法和步骤。据此原理和方法,使用C语言设计开发出了应用实例——折线浓淡分布曲线。     

Electrochemical impedance spectroscopy of a free-standing oxide film

The corrosion of low carbon steel in natural sea-water is characterized by the formation and growth of compact and thick layers composed of oxides, insoluble salts and organic materials. These layers are the result of corrosion processes induced by local environmental conditions, water oxygen supply; ionic species; bacteria and organic matter. The exchange of various species (ions, molecules, gas) between sea-water and the rust layers or the metal depends both on the kinetics of the Faradaic reactions of the entities with either the oxides or the metal, as well as on their transport properties through the different strata of the rust layers. In this work, an impedance study was carried out using the 4-electrodes cell arrangement with corrosion products picked up on steel sheet piling immersed for 25 years and analyzed as free standing membranes. This new approach is a good way to reach the specific transport and transfer properties of the oxide without being blurred by the metal influence. The physical model developed in this work was based on a transmission line, and accurately described the experimental diagrams. The electronic resistivity of the oxide layer, its porosity, the mean pore size and the reaction kinetics parameters could be determined from the fittings.