Surface Areas of Nitrated Hydrotalcites

Hydrotalcites in the nitrate form were prepared using microwave irradiation in the hydrotreatment step. The surface area (BET) of nitrated hydrotalcites was evaluated. Solids were characterized by atomic absorption, X-ray diffraction and BET analysis. Thermal pretreatment temperature determined the surface area of the hydrotalcites.     

超薄聚合物表面上滴状冷凝的传热研究

本文采用等离子体聚合和离子束动态混合注入技术在不同的基材(黄铜、紫铜、不锈钢和碳钢)上制备了聚六氟丙烯和聚四氟乙烯的超薄膜,并进行了垂直管外的水蒸汽的滴状冷凝实验。实验发现,对于不同的基材,表面制备的工艺参数对冷凝传热性能及维持滴状冷凝的寿命具有显著的影响。表面性能的测试和估算为预测给定蒸汽在某表面是否成滴提供了依据。     

Oxidation of acrolein on a multicomponent oxide catalyst

Catalytic oxidation of acrolein to acrylic acid has been studied and the optimum composition of the multicomponent catalyst Mo _a V _b Cu _c Fe _d O _x has been found. The reaction kinetics has been measured.     

Comparison of the Effect of a Hydrocarbon Oil and a Terpene Tackifier on the Autohesion of Styrene-Butadiene Rubber

Blends of uncrosslinked styrene-butadiene rubber (SBR) with a terpene tackifier resin or a naphthenic oil have been characterized, and their autohesion and cohesion determined using a T-peel geometry. SBR/oil blends are homogeneous at all proportions, while SBR/resin blends, based on DSC and DMA analysis, undergo bulk phase separation at about 50% resin. However, migration of tackifier to the surface region is proposed at much lower resin contents. Compositions diluted with oil have autohesion similar to the neat SBR. This is attributed to compensating effects; although oil hastens self-bond formation by increasing chain mobility, this is nearly equally balanced by more facile chain separation during bond rupture. In short, oil-diluted compositions are soft and weak. On the other hand, SBR compositions containing small amounts of resin have high autohesion. Resin-diluted specimens deform easily at low strain, just as those containing oil, but intertwined chains of the former have greater resistance to separation, due at least in part to higher glass transition temperatures. It is proposed that autohesion is further enhanced by migration of tackifier to the surface. This causes SBR/resin compositions to be both soft and strong-a necessary condition for high autohesion.     

T406型脱氯剂的研制与工业应用

报导了型脱氯剂的研制、性能试验和工厂运行结果。与国内外常见同类脱氯剂的对比试验及工业应用表明, 由化工部西北化工研究院开发研制的这一新型脱氯剂具有抗压碎强度高, 净化度高, 氯容量高的特点, 可以在常温下用于气相和液相原料中氯化物的脱除。即使在低温（4℃）下, 净化后原料中氯降至左右的情况下抓容量仍高达18％以上。该脱氯剂还能同时脱除原料中的硫。T406型脱氯剂已工业应用于混合二甲苯和氢原料的脱氯, 使用效果良好。     

接种固氮菌对纤维素分解过程的影响

从纤维素分解菌与联合固氮菌的接种配比,研究了混合培养对滤纸分解的影响。试验共设6个处理样,总接种量均为10%(V/V):处理Ⅰ,2%固氮菌+8%纤维素分解菌;处理Ⅱ,4%固氮菌+6%纤维素分解菌;处理Ⅲ,6%固氮菌+4%纤维素分解菌;处理Ⅳ,10%纤维素分解菌;处理Ⅴ,10%固氮菌;CK(空白对照)。结果显示:与处理Ⅳ相比,处理Ⅰ、Ⅱ的CMC酶活力及处理Ⅰ、Ⅱ、Ⅲ的滤纸分解率有明显提高。接种固氮菌的各处理样中,培养液中氮素含量与CK相比均有显著提高(P<0.05),且培养过程中pH值比较平稳,而未接种固氮菌处理培养液的氮素则低于CK,pH急剧降低。所有处理样中,接种2%固氮菌效果最佳,培养192h,其CMC酶活力与滤纸分解率比处理Ⅳ分别提高43.4%、240%;与处理Ⅴ相比,固氮菌数有显著增加(P<0.05),培养液中氮含量提高28.0%。     

含水混酸的酯化分离试验

基于中国石化扬子石化公司化工厂醋酸装置产生大量的含水甲酸、乙酸副产品,通过试验将含水混酸进行酯化、分离,得到符合工业品规格的甲酸乙酯、乙酸乙脂。试验确定酯化塔回流比为3∶1,乙醇分批次加入,乙醇实际投入量与理论量的比为1.2。酯化分离结果:甲酸乙酯的单程收率89.5%,纯度大于97%,乙酸乙酯的单程收率80.1%,纯度大于97%。     

某砖混结构加层改造的设计

通过对某砖混结构加层改造的设计实践,介绍了加层改造的方法,分析了在加层改造过程中需解决的问题。主要包括地基及基础的处理,墙体抗压、抗震验算,节点连接处理,如何保证新结构与原结构连接的整体性,楼梯间处理,构造柱的连接等,并提出了结构加层对施工技术的要求。给出一些具体的构造大样,供工程设计参考。     

Selective oxidation of ammonia to nitrogen on transition metal containing mixed metal oxides

The selective catalytic oxidation of ammonia to nitrogen (NH₃-SCO) has been studied over hydrotalcite derived mixed metal oxides containing Cu, Co, Fe or Ni. XRD, BET, NH₃-TPD and TPR techniques were used for catalysts characterization. Results of NH₃-SCO were compared with those of selective catalytic reduction of NO with NH₃ (NO-SCR). Reaction mechanism was studied by temperature-programmed surface reaction (TPSR) and activity tests with a various contact time. Catalytic performance of the studied samples depends on both kind and loading of transition metals in the mixed metal oxide system. The Cu-containing samples have been found to be the most active catalysts of the NH₃-SCO process. Transition metal loading strongly influences distribution of ammonia oxidation products. The highest selectivity to N₂ was measured for the catalysts with the lowest transition metal content.     

Effect of mixing leaves with olives on organoleptic quality of oil obtained by centrifugation

Variable quantities of leaves were added to ripe olives prior to extraction to determine their effect on the quality of the resulting olive oil. The addition of 1–3% w/w leaves improved the organoleptic quality. An increase intrans-2-hexenal aldehyde content occurred, giving the pleasant flavor of “freshly cut grass.” This compound was produced by the enzymatic breakdown of 13-L-hydroperoxide of linolenic acid in leaf homogenates.