Estimating crystallinity in high density polyethylene fibers using online Raman spectroscopy

Online Raman spectra, obtained at different points along the spin line during pilot‐scale nonisothermal melt spinning of high density polyethylene (HDPE) fibers, are presented for the first time. The fraction of the crystalline phase corresponding to each spectrum was determined from the normalized integrated intensity of the 1418 cm^?1 Raman band. It is well established that this band represents the orthorhombic crystalline phase in polyethylene. The estimates of percent crystallinity obtained from decomposition of the Raman spectrum were compared with the percent crystallinity from differential scanning calorimetry (DSC) measurements. It is concluded that online Raman spectroscopy can be successfully used to monitor the development of crystallinity in HDPE fibers as a function of distance from the spinneret. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 545–549, 2003     

Fracture toughness of PAN-based carbon fibers estimated from strength-mirror size relation

Fracture toughness (K_IC) of representative high-strength type PAN (polyacrylonitrile)-based carbon fibers, Torayca™ T300 and T800H, with or without artificial surface defects, were estimated to be ca. 1 MPam^1/2 from the tensile strength vs. fracture mirror size relation, assuming a constant crack-to-mirror size ratio. The corresponding critical energy release rate (Γ) was ca. 7.4 J m⁻², which was close to the value derived from the reported surface energies for a graphite crystal. Similar K_IC values were obtained for the old-type PAN-based carbon fibers from the reported data by the use of the present estimation procedure.     

Reduction mechanism of tioglycolic acid on keratin fibers using microspectrophotometry and FT-Raman spectroscopy

In order to investigate the reduction mechanism of thioglycolic acid (TG) on the keratin fibers, cross-sectional samples of white human hair treated with TG were prepared. The heterogeneous reaction between TG and keratin fibers involving the diffusion of TG into human hair was analyzed at the molecular level using microspectrophotometry and FT-Raman spectroscopy. The diffusion of TG into human hair clearly increased by increasing the treatment time and by raising pH. The TG relative concentration and the disconnected relative concentration of disulfide (–SS–) groups at various depths of the hair samples with pH 9.0 were in good agreement, indicating that the reaction rate (the disconnection of –SS– groups) was faster than the diffusion rate of TG into human hair. From these experiments, we demonstrated that TG diffuses gradually beyond the cuticle region, and toward the inside of the cortex region along with the disconnection of –SS– groups.     

Measurement and numerical simulation of three‐dimensional fiber orientation states in injection‐molded short‐fiber‐reinforced plastics

To determine three‐dimensional fiber orientation states in injection‐molded short‐fiber composites, a confocal laser scanning microscope (CLSM) is used. Since the CLSM optically sections the specimen, more than two images of the cross sections on and below the surface of the composite can be obtained. Three‐dimensional fiber orientation states can be determined by using geometric parameters of fiber images obtained from two parallel cross sections. For experiments, carbon‐fiber‐reinforced polystyrene is examined by the CLSM and geometric parameters of fibers on each cross‐sectional plane are measured by an image analysis. In order to describe fiber orientation states compactly, orientation tensors are determined at different positions of the prepared specimen. Three‐dimensional orientation states are obtained without any difficulty by determining the out‐of‐plane angles utilizing fiber images on two parallel planes acquired by the CLSM. Orientation states are different at different positions and show the shell–core structure along the thickness of the specimen. Fiber orientation tensors are predicted by a numerical analysis and the numerically predicted orientation states show good agreement with measured ones. However, some differences are found at the end of cavity. They may result from the fountain flow effects, which are not considered in the numerical analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 500–509, 2003     

快速烧结法制备连续碳化硅纤维

通过熔融纺丝，不熔化处理制得连续聚碳硅烷（ＰＣＳ）不熔化纤维，采用快速烧结方法制备出性能较好的连续ＳｉＣ纤维。探讨了气封条件的选择，以及烧结速度对ＳｉＣ纤维的组成，结构及性能的影响。结果表明，快速烧结条件下，可以实现向纤维上施加张力以及纤维的无机化转变，烧结速度加快会降低纤维的Ｃ／Ｓｉ（原子比），同时有利于提高纤维的抗拉强度和热稳定性。     

Abrasion phenomena in twill tencel fabric

The abrasion characteristics of Tencel fabrics were evaluated by Martindale abrasion and laundering, and the breakdown mechanism of fibers was surveyed by scanning electron microscopy. The fabric was subjected to pad‐dry‐cure treatment with two different types of modified dimethyloldihydroxyethylene urea resins (Reaktant DH and Reaktant FC). Although the degree of dry abrasion varied with different resins, the damage exhibited by individual fibers differed little from untreated to resin‐treated; the major mechanism of abrasion was through friction, and the mechanism of fiber failure was multiple splitting and transverse cracking. In untreated Tencel, the characteristic feature of wet abrasion was massive fibrillation, and in crosslinked fabrics, the wet abrasion mechanism was through fiber slippage and slicing action, although in the Reaktant FC‐treated fabric, the wet abrasion mechanism was more through slicing than through fiber splitting. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1391–1398, 2006     

中国光纤通信技术的研究、应用和发展

主要从光纤光缆、光器件与组件、光传输设备与系统、光网络建设等方面论述光纤通信技术在我国的研究、应用发展历程，并对我国光纤通信技术的未来发展进行展望。     

光纤模式噪声的研究

综述了光纤模式噪声的产生、计算，并介绍了减小它的一些方法。