Photocatalytic degradation of gaseous perchloroethylene in continuous flow reactors: Rate enhancement by chlorine radicals

The degradation of perchloroethylene (PCE) by UV/TiO₂ photocatalysis in gas phase was studied. The degradation efficiency has been compared in different continuous flow reactors: a photocatalytic tangential reactor (PTR) where the air flows tangentially over the catalytic medium and two photocatalytic filtering reactors (PFR) where the air flows through the porous catalytic medium. The degradation rate shows a linear dependence with the concentration of pollutants (up to 350 mg PCE/N m³) for the PTR, but the degradation was negligible for the PFR. The degradation rate was enhanced by accelerating the chlorine radicals’ formation (by adding HCl in catalytic quantity in the air flow or by PCE over-heating). In these conditions, the oxidation rate constant of PCE in the PFR was about five times higher than that in the PTR, although the mass of catalyst involved in the PFR was about 10 times lower and the contact time was about a 1000 times shorter than that of the PTR. Thus, the catalyst is globally more efficiently used in the PFR, as the mass transfer is not limiting. As a result, a degradation mechanism of PCE, involving the generation of free chlorine radicals, as the first limiting step, has been confirmed.     

TiO_2-聚乙烯复合膜的制备及红外光谱对其膜层结构的表征

开发了以Ｔｉ４＋为桥联剂制备无机－有机复合膜的新方法以自制的硅藻土多孔陶瓷为基膜（支撑体），使用浸涂法－热致相转化法相结合制备了ＴｉＯ２－聚乙烯复合膜，并用红外光谱表征了复合膜层与层之间的结合方式和强度，支撑体中的ＳｉＯ２通过Ｔｉ４＋与聚乙烯的分子之间形成了新的化合物型膜层     

热处理温度对溶胶-凝胶法制备的TiO2薄膜性能的影响

采用溶胶-凝胶法在普通载波片上制备了TiO2薄膜,用AFM、XRD、UV-VIS分光光度计、润湿角测量仪研究了薄膜的表面形貌和热处理温度对薄膜各种性能的影响.结果表明:TiO2薄膜由大量的球形纳米颗粒构成,颗粒大小均匀;随着热处理温度的升高,TiO2薄膜晶粒尺寸不断长大,亲水性和光催化性能提高;600℃时部分TiO2由锐钛矿转变为金红石相,使紫外光吸收线“红移”.     

Single and combined deactivating effect of alkali metals and HCl on commercial SCR catalysts

Two commercial SCR catalysts, with a nominal W content of about 9 wt.% and a V nominal content of 0.55 and 1.8 wt.%, respectively, were contacted with different amounts of Na and K and with HCl vapours in order to simulate poisoning by species more specifically contained in exhaust gases from MSW combustion. Catalysts were characterised using XRD analysis, SEM/EDX analysis, BET and pore size distribution measurements, NH₃ TPD, TG analysis. Poisoning agents do not cause loss of surface area nor pore occlusion. A significant loss of surface acidity was observed upon alkali metals poisoning whereas a decreasing of vanadium content was observed for the more concentrated catalysts upon HCl poisoning. Catalysts deactivation is proportional to the number of acid sites neutralised by alkali metals adsorbing ammonia in the temperature range typical of SCR process. HCl promotes the formation of new acid sites showing a lower activity compared to the original one.     

低电压氧化锌压敏电阻器的研究

研究了一种制造低电电压氧化锌压敏电阻器的方法。在基本成分的基础上适当加入二氧化钛可降低梯度电压（Ｖ１ｍＡ／ｍｍ），适量掺硼和改进热处理工艺可减小元件的漏电流和提高其稳定性。     

钨酸铵溶液浓度对超微钨粉形貌的影响

以钨酸铵溶液为原料，采用超声喷雾干燥法制备了超微钨粉。研究了该方法中钨酸铵浓度对超微钨粉形貌的影响。结果表明，当溶液中钨酸铵的浓度为10%时，得到了球形度很好的非完全结晶的前驱体。当钨酸铵浓度达25％时，得到了层片状的晶态前驱体。钨酸铵溶液浓度对干燥时晶体生长速度具有重要的影响。分别采用这2种前驱体在630℃，保温30min和氢气流莆4L／min条仲下能够完全还原，得到超微α—W粉。所制得的钨粉形貌完全遗传了其前驱体的形貌，分别得到球状和层状钨粉。球状钨粉由纳米颗粒聚集而成。片层状钨粉的厚度在1mm以下。     

光催化TiO2涂层在金属防腐蚀中的应用研究现状

介绍了TiO2的特点、应用概况及金属光催化防腐蚀作业的原理，对光催化TiO2涂层在金属防腐蚀方面的应用研究进展进行了综述。指出了TiO2薄膜在这一领域应用中的优势及存在的问题。     

锐钛型介孔纳米二氧化钛粉体的制备与表征

采用沉淀法,以水溶液为反应体系,无机物（硫酸氧钛和氢氧化钠）为主要原料,加入少量模板剂,制备出锐钛型介孔纳米二氧化钛粉体。通过正交实验分析优选出最佳工艺。采用比表面仪、原子力显微镜（AFM）、高分辨场发射透射电镜等仪器对产品的结构进行了表征,得到了具有较高热稳定性,比表面积为121 m2·g-1,晶粒尺寸为12 nm,介孔平均孔径为10 nm,粉体粒径＜100 nm等特征的锐钛型介孔纳米二氧化钛粉体。     

铈基SCR脱硝催化剂研究进展

近年来铈（Ce）基脱硝催化剂成为低温脱硝领域的研究热点,按载体类型可分为金属氧化物催化剂、二氧化钛载体催化剂、分子筛载体催化剂、活性炭及氧化铝载体催化剂等。按催化剂种类分别介绍了掺杂改性、制备工艺、反应条件等对催化剂性能的影响,并阐述了可能的原因机理。目前,铈基催化剂大多处于实验室阶段,工业化应用尚存在问题,尤其作为低温脱硝催化剂,活性中心堵塞问题更加突出,并且催化剂成本较高。未来可从催化剂制备工艺入手解决催化剂成型问题,以实现工业应用。同时探讨催化剂中毒机理,进一步提升其抗中毒能力。另外,寻求适宜的材料与铈掺杂组合,达到高效脱硝和经济效益最大化。     

Pd^2＋离子对TiO2光催化薄膜化学稳定性的影响

采用Sol—Gel工艺在普通玻璃表面制备出均匀、透明的添加0．3％～0．5％贵金属Pd^2 的TiO2-SiO2复合薄膜。通过对薄膜的XRD，SEM表征及薄膜耐酸、碱化学稳定性的检测，结果表明，在TiO2—SiO2薄膜中添加Pd^2 ，增强了TiO2薄膜的光催化活性，由于Pd^2 所起到阻滞剂的作用，使晶粒尺寸减小，表面呈多孔合理结构，改善了TiO2薄膜的显微结构，使薄膜的化学稳定性得到明显的提高。