Investigation of texture effect on visual colour difference evaluation

The texture effect on visual colour difference evaluation was investigated in this study. Five colour centers were selected and textured colour pairs were generated using scanned textile woven fabrics and colour‐mapping technique. The textured and solid colour pairs were then displayed on a characterized cathode ray tube (CRT) monitor for colour difference evaluation. The colour difference values for the pairs with texture patterns are equal to 5.0 CIELAB units in lightness direction. The texture level was represented by the half‐width of histogram, which is called texture strength in this study. High correlation was found between texture strength and visual colour difference for textured colour pairs, which indicates that an increasing of 10 units of texture strength in luminance would cause a decreasing of 0.25 units visual difference for the five colour centers. The ratio of visual difference between textured and solid colour pairs also indicates a high parametric effect of texture. © 2005 Wiley Periodicals, Inc. Col Res Appl, 30, 341–347, 2005; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/col.     

Evaporation and Evolution of Suspended Solution Droplets at Atmospheric and Reduced Pressures

Thermal history and solute precipitation behavior of suspended solution droplets of sodium chloride (NaCl), magnesium sulphate (MgSO₄), and zirconium hydroxychloride (ZrO(OH)Cl) evaporating at atmospheric and reduced pressures are studied. Experimental measurements on the variation of droplet diameter, solution concentration, and temperature during the evaporation period are presented and discussed. The results of solute precipitation behavior in solution droplets observed under an optical microscope are displayed and discussed. Results indicate that reducing the pressure (∼ 33 kPa) results in a change in the solution droplet evaporation rate, but the thermal histories of a particular solution droplet are similar at the atmospheric and reduced pressures. At atmospheric and reduced pressures used in this study, the d² law for solution droplets is valid at early stages of the evaporation and before the solute precipitation initiates. Drying of MgSO₄ and ZrO(OH)Cl solution droplets results in the formation of spherical particles, whereas drying of spherical NaCl solution droplets results in the formation of cubic particles.     

Schäden durch kerbinduzierte Schwingbrüche

Failures by notch induced fatigue fractures Notches produce local stress concentrations and promote the formation of fatigue cracks. Characteristic types of notches as a result of design, manufacturing and operation are presented and remedial measures are discussed. Examples demonstrate the effect of different kinds of notches on various components.     

Photoresponsive peptide and polypeptide systems: part II. Photochromism of poly(l-ornithine) containing various azo-contents in side chains

Poly(L-ornithine)s having various azo-contents in the side chains were synthesized by the water-soluble carbodiimide procedure. The photochemical properties of the polypeptides poly[N^δ-p-(phenylazo)benzoyl-L-ornithine] (PPABLO) containing 3–77 mol% azobenzene were investigated by absorption and circular dichroism spectroscopy in hexafluoro-2-propanol (HFIP) or water, and in HFIP-water or methanol-water solvent mixtures. The photochromism of the dichroic bands of the PPABLOs containing 20–77 mol% azobenzene in the visible and ultraviolet wavelength regions was found to be mostly reversible as a function of irradiation time at different wavelengths due to the photostationary state (above 80% trans-cis photoisomerization) of the azo aromatic moieties. The PPABLO containing 3.2 mol% azobenzene in water exhibited conformational changes from random coil to helix by the addition of methanol or sodium dodecyl sulphate (SDS). The photo-induced conformational change was observed in HFIP-water-SDS solvent mixtures, while no conformational change was seen in water and HFIP-water solvent mixtures.     

Cohesive stresses and size effect in quasi-brittle materials

A novel approach to the derivation of Bažant’s size effect law is presented. Contrarily to the original Lagrangian derivation which hinged on energetic consideration, a Newtonian approach based on local stress intensity factors is presented. Through this approach, it is shown that Bažant’s size effect law is the first (and dominant) term in a series expansion for the nominal stress. Furthermore, analytical expressions forB are derived for selected specimen geometries.     

Effects of α‐form or β‐form nuclei on polymorphic crystalline morphology of poly(butylene adipate)

The effects of α‐form and β‐form nuclei on polymorphic morphology of poly(butylene adipate) (PBA) upon recrystallization from the molten state up to various T_max values were examined by differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction (WAXD) and polarized light microscopy (PLM). In this study, PBA with complex melting and polymorphism behaviour was used as a model for examining different types and extents of residual nuclei. As the PBA initially containing the sole α‐crystal was brought to a molten state of various T_max, the extents of trace α‐form crystal nuclei varied and were dependent on T_max. Furthermore, it did not matter whether, initially, the PBA contained α‐ or β‐form crystals (or both) because only a single type of α‐nuclei could be left upon treatment to the molten liquid state at T_max. Therefore, only the α‐crystal in PBA had ‘memory capacity’ in the molten liquid state while the β‐crystal did not. This was so because the latter had been completely transformed into the solid state prior to being heated into a liquid. PBA crystallized before α‐nuclei could be packed into α‐crystal, regardless of the crystallization temperature (T_c). For recrystallization from molten PBA without any nuclei, the crystalline polymorphism was correspondingly influenced by T_c. Copyright © 2005 Society of Chemical Industry     

"JDS-音频化渣微机综合检测系统"的应用与效果

简要介绍“JDS-音频化渣微机综合检测系统”的工作原理和应用效果，证明使用该装置是提高炼钢操作水平的一条较好途径。     

The oxidation of two ternary Ni-Cu-10 at.% Al alloys in 1 atm of pure O2 at 800-900 °C

The oxidation of the ternary alloys Ni-45Cu-10Al and Ni-30Cu-10Al has been studied at 800-900 °C under 1 atm O₂. The presence of 10 at.% Al reduces significantly the oxidation rate of the corresponding Cu-Ni alloys during the initial oxidation stages, even before the establishment of a complete Al₂O₃ layer. The weight of individual sample of the two ternary Ni-Cu-10Al alloys at 800 °C increases more rapidly than at 900 °C during the initial oxidation stage. As oxidation proceeds, the weight gain at 800 °C slows down to a degree that the total weight gain after 24 h oxidation at 800 °C is less than that at 900 °C. Due to a faster formation of the Al₂O₃ layer, which suppresses earlier the further oxidation of Cu and Ni, the external region of the scales grown on Ni-45Cu-10Al contain much less Cu and Ni oxides than those grown on Ni-30Cu-10Al. The transition from the internal oxidation to the selective external oxidation of the most reactive component Al in Ni-Cu-Al alloys is favored by higher values of the Al content, of temperature and of the Cu/Ni ratio.