Cooperative Effect Radiation Loss of Optical Pump Solid Laser

1 Introduction For increasing the output energy of laser, the pumping power must be enhanced. But the cooperative effect will arise and cause spontaneous radiation light in laser medium sample when the pumping power is high e- nough without the resonator. The spontaneous radiation light is coherent light between laser and fluorescent. It will compete the upper energy level population with ex- cited radiation, and the loss increase. In solid laser medium, such as Nd∶YAG, the Nd ion densityi…     

The radiation crosslinking and scission of ethylene-propylene copolymers studied by solid-state nuclear magnetic resonance

Methyl groups from chain scission and H-crosslinks have been identified by solid-state nuclear magnetic resonance in amorphous ethylene-propylene copolymers containing 23 and 36 mole % propylene after γ-irradiation to 10 MGy at 30°C. G (scission) and G (crosslink) values determined from the n.m.r. spectra and by extraction are in agreement, which suggests that the crosslinks are not clustered. This may differ from the situation in polyethylene where there is a substantial crystalline content. G(S). G(X) and the ratio G(S)/G(X) increase with increasing propylene content of the copolymers.     

金属/聚合物复合材料对中能电子的屏蔽作用研究

运用MULASSIS计算程序模拟计算了不同组成的屏蔽材料对空间辐射环境的屏蔽效果,在此基础上进行屏蔽材料的初步设计,并制备了一系列不同组成的金属/聚合物复合材料,结合中能电子照射的实验结果,讨论了组成对金属/聚合物复合材料的屏蔽效果的影响.研究发现,高原子序数和低原子序数金属混合添加的复合物样品具有较好的屏蔽效果.     

无线随钻测量技术的应用现状与发展趋势

目前,无线随钻测量技术是石油工程技术发展的一个主要方向。详细介绍了无线随钻测量仪器的传输方式、国内外无线随钻测量技术的主要进展和应用现状,指出了国内外无线随钻测量仪器的优缺点和应用范围,分析了无线随钻测量技术的发展趋势,并提出我国应在借鉴国外先进的无线随钻测量技术的基础上,研制具有自主知识产权的无线随钻测量仪器,以加快我国无线随钻测量技术的发展,缩短与国际先进水平的差距。     

薄板坯连铸连轧工艺对铌微合金化高强度钢组织和性能的影响

首先建立薄板坯连铸连轧工艺的试验室模拟技术，并运用该模拟技术，研究薄板坯连铸连轧工艺(CSP)和传统板坯再加热工艺(TRP)两种工艺对铌微合金化高强度钢的显微组织和力学性能的影响。研究结果表明：CSP钢的晶粒细化效果不如TRP钢，两者的平均铁素体晶粒尺寸分别为8．17μm和6．30μm。在CSP试验钢板中铌的析出量较大，特别是在铁素体中细小颗粒的铌的析出物较多，沉淀强化效果较强。CSP试验钢的σ0.5和σb分别较TRP工艺低约40MPa和约25MPa，同时其低温冲击韧性较好，FATT温度较低。     

Surface Hardening of High-Strength Low Alloy Steels (HSLA) Dual-Phase Steels by Ball Burnishing Using Factorial Design

Burnishing is used increasingly as a finishing operation which gives additional advantages such as increased hardness, fatigue strength, and wear resistance. Experimental work based on 3⁴ factorial design was carried out to establish the effects of ball burnishing parameters on the surface hardness of high-strength low alloy steels (HSLA) dual-phase (DP) steel specimens. Statistical analysis of the results shows that the speed, feed, lubricant and ball diameter have significant effect on surface hardness.     

基于TiNi合金的超弹性对其相关磨损机制的FEM研究

本文在重点考虑TiNi合金高弹性变形量的前提下，采用等向强化模型，对不锈钢和超弹TiNi合金在法向接触载荷作用下的六种模型进行了有限元(FEM)分析。结果表明：在相同载荷条件下，超弹TiNi合金产生的von Mises弹性应变要高于不锈钢，但其von Mises应力和塑性应变却恰恰相反，在同一载荷下该合金发生塑性变形的区域要小于不锈钢；此外，超弹TiNi合金发生塑性变形要比不锈钢困难，所需的临界载荷值随其最大弹性变形量(屈服点处的应变值)的增加而增加。最后，基于本文的有限元计算结果对超弹TiNi合金的蘑粒磨损和疲劳磨损机制进行了讨论。     

乙烯裂解炉辐射炉管施工技术

乙烯裂解炉辐射炉管的施工比较复杂,文章结合吉林石化分公司15万t／a乙烯装置节能改造项目的施工实践,介绍了辐射盘管系统施工的准备工作、辐射盘管组装顺序、集管箱开孔及组焊、猪尾管预制安装、辐射盘管吊装等方面的施工经验。     

低发射率材料红外法向发射率谱测量方法的研究

采用热管技术研制了材料发射率谱的专用测量附件;利用双温测量技术,在P-E983型红外分光光度计及3600型数据站上进行了较低温度下低发射率材料红外法向发射率谱测量方法的研究.实测了几种材料的发射率谱;讨论了影响测量误差的诸因素.     

高层天台移动通信天线电磁辐射影响水平探讨

移动通信基站在高层建筑天台架设的定向天线，对周围环境的电磁辐射影响水平的监测进行分析，探讨高层建筑天台电磁辐射环境的污染防治对策。