纳米级BaAl_2O_4微粉的制备和性质

分别用溶胶 -凝胶法、低温固相反应法 ,制得了纳米级BaAl2 O4微粉 ,用电镜观察了其形貌和粒径的大小 ,用X-射线衍射仪进行了物相分析 ,测定了其纯度与晶型 ,讨论了制备方法与粒度大小的相互影响     

以齐聚副产物制备耐高温泡沫剂

以齐聚副产物为原料在实验室分别以AlCl3、AlCl3络合物和杂多酸为催化剂合成并经磺化制备了用于提高石油采收率的耐高温泡沫剂，试验结果说明烷基碳数为16的异构烷基苯磺酸盐常温发泡性能最佳，烷基碳数大于20的正构烷基苯磺酸盐高温发泡性能最佳，后者特别适合高温蒸汽驱油。加入适当的非离子助剂及无机盐能够提高磺酸盐的水溶性，改善发泡剂溶液的稳定性。     

甲醇氧化羰化制碳酸二甲酯产物气相色谱分析

以Chromosorb 10 1为固定相 ,气相色谱法分析甲醇氧化羰化制碳酸二甲酯产物中水、甲醇、乙酸甲酯和碳酸二甲酯等组份的含量 ,考察了柱温 ,载气流量对分离度的影响 ,确定了适宜的分析条件 ,并用校正面积归一化法定量。该方法操作简便 ,快速 ,精度高 ,重现性好     

Asymmetric Hydrogenation of Activated Ketones on Platinum: Relevant and Spectator Species

The heterogeneous enantioselective hydrogenation of activated ketones over chirally modified platinum is reviewed with emphasis on identifying the role of the various species observed in this catalytic system. The past years have witnessed a continuous broadening of the scope of this catalytic system including new reactants and modifiers affording over 97% ee. New reaction pathways have been uncovered and the kinetic and mechanistic studies have been faced with a number of complicating factors caused by spectator species and interactions in solution and on the Pt surface. The previously proposed mechanistic models are critically assessed in the light of these new findings.     

Texture Changes During the Ripening of Port Salut Argentino Cheese in 2 Sampling Zones

ABSTRACT: Texture changes during ripening of Port Salut Argentino cheese for different sampling zones were studied. Compression relaxation tests were performed and results were analyzed using both Maxwellian and Peleg's models. Elastic equilibrium modulus obtained from the Maxwellian model decreased from 1.22 to 0.11 10⁴Pa during ripening. The constants derived from Peleg's model, k₁ and k₂, diminished with ripening time from 1.18 to 0.71 min and from 1.27 to 1.12, respectively. Asymptotic equilibrium modulus from Peleg's model decreased from 0.95 to 0.07 10⁴Pa during ripening. Rate parameters derived from a 1st order kinetics applied to both equilibrium moduli showed that the decrease was faster in the external zone (0.0846 d⁻¹) than in the central zone (0.0368 d⁻¹). The correlation between equilibrium moduli, salt concentration, moisture content, and maturation indexes was obtained with a determination coefficient of 0.76.     

三水草酸铀酰的红外激光化学

文章研究了三水草酸铀酰(UO_2C_2O_4·3H_2O)在兆瓦脉冲二氧化碳激光辐照下的红外激光化学反应,它与草酸铀酰的热分解反应不同,反应产物是二氧化铀和二氧化碳。反应的量子效率随激光波长不同而变化。     

功能化的介孔分子筛碱催化性能的研究

以苯甲醛与氰乙酸乙酯的Knoevenagel缩合为模型反应，研究了用γ－氨丙基三乙氧基硅烷或γ－乙二胺丙基三甲氧基硅烷功能化的纯硅介也分子筛HMS（Hexagonal mesoporous silica）的碱催化性能。结果表明，除个别碱基负载量高的样品外，功能化样品对反应显示很高的催化活性，反应的初期活性不仅取决于催化剂上活性中心的密度，而且与载体的孔道结构有关。大孔径载体有利于反应物、产物的扩散，故在高负载量时，大孔径样品比小孔样品有更高的活性。此外，还考察了反应温度、溶剂、反应物配比和催化剂用量等条件的影响以及催化剂的重复使用情况。结果表明，反应可在低于100℃的温和条件下进行，有明显的溶剂效应，反应物配比和催化剂用量存在一最佳值；随使用次数的增加，催化剂逐渐中毒而失活。     

CMS/TiO2杂化材料电流变液的制备及其性能

利用特殊的溶胶凝胶方法原位制备了改性淀粉与无机钛氧化物杂化型电流变材料。实验表明,在强电场下其电流变效应比相同组份的淀粉、二氧化钛混合型电流变液有显著提高,直流电场4 kV/mm,剪切速率5 s-1时,静态剪切屈服强度可达4000 Pa以上。同时,抗沉降性明显改善,静置100 h几乎不沉淀。此外,温度效应也获得一定的优化,在10 ℃~90 ℃的工作温度范围内力学性能保持良好,70 ℃时剪切强度达到最大值。     

A STUDY ON ACIDITY AND CATALYTIC PROPERTY OF [B] ZSM-5 CATALYST MODIFIED WITH SILICON COMPOUND BY CHEMICAL SURFACE DEPOSITION OF LIQUID-PHASE TECHNIQUE

The boron heteroatom zeolite catalyst has been modified with silicon compound by Chemical Surface Deposition of Liquid-phase (CLD) technique and the catalytic property of the modified catalyst is studied. Meanwhile, the acidity of the modified zeolite catalysts is characterized through TPD and IR technique, and the fluid adsorption method is used to determine its pore structure. The relationship between the catalytic property of the zeolite catalyst and its pore structure, its acidity has been found. The results of toluene-ethylene alkylation reaction indicate that the selectivity of p-ethyltoluene on the modified zeolite catalyst is higher than that on the zeolite catalyst before silanizated, reaching 94.14%.     

Intermetallic compounds formed at the interface between liquid indium and copper substrates

The interfacial reactions between liquid In and Cu substrates at temperatures ranging from 175°C to 400°C are investigated for the applications in bonding recycled sputtering targets to their backing plates. Experimental results show that a scallop-shaped Cu₁₆In₉ intermetallic compound is found at the Cu/In interface after solder reactions at temperatures above 300°C. A double-layer structure of intermetallic compounds containing scallop-shaped Cu₁₁In₉ and continuous CuIn is observed after the Cu/In interfacial reaction at temperatures below 300°C. The growth of all these intermetallic compounds follows the parabolic law, which implies that the growth is diffusion-controlled. The activation energies for the growth of Cu₁₆In₉, Cu₁₁In₉, and CuIn intermetallic compounds calculated from the Arrhenius plot of growth reaction constants are 59.5, 16.9, and 23.5 kJ/mole, respectively.