On basic definitions of unified fracture mechanics terminology

The adoption of unified fracture mechanics terminology (UFMT) will promote efficient communication between specialists in different fields of fracture research, harmonization of national and international standards relating to fracture mechanics, and last but not least improvement of the existing methodology for teaching and education in fatigue and fracture. In this paper the definitions of some basic and related terms included in different standards on fracture mechanics terminology are confronted with one another. Alternative definitions of the same terms are offered. By this strategy the author tries to show that the definitions of basic and related terms appropriate for the UFMT should emerge as a consequence of harmonizing a crack model with an actual crack and then both taken together with a fracture model, laboratory test methods, and failure assessment codes.Published in Problemy Prochonsti, No. 1, pp. 17–29, January, 1996.This paper is published as a matter of discussion.     

Reliability and performance analysis of time – space – time switching networks with multiple separated space switches

Since electronic switching systems usually require very strict reliability requirements as well as good performance objectives, we need to jointly analyse the performance and reliability of switching systems. In this paper, we compare conventional time–space–time switches with single space switches with those with multiple separated space switches, from the viewpoints of reliability and performance. We consider time–space–time switching networks which consist of N incoming time switches, i.e. one NxN space switch, two (N/2)x(N/2) space switches, and four (N/4)x(N/4) space switches. We introduce a Markov reliability model to study the effect of failures and analyse the reliability and performance of three different types of switching networks in terms of average blocking probability and the mean time to unreliable operation, as we vary the offered traffic. As a result, T–S–T switching networks with multiple separated space switches exhibit better performance and reliability than those with single space switches.     

Effect of Bi and Sr concentrations on the formation of the 2223 phase in Bi-Pb-Sb-Sr-Ca-Cu-O materials, obtained under different conditions of thermal treatment

The superconducting properties and the phase and chemical composition of Bi _x Pb_0.3Sb_0.1Sr _y Ca₂Cu₃O_z (x=1.5, 1.6, and 1.7;y=1.9, 2.0, and 2.1) materials synthesized by one-step and multistep thermal treatments have been investigated. The multistep annealing between 825–875°C promotes the 2223 phase. The change of Bi concentration has little effect on the 2223 phase formation, regardless of the kind of thermal treatment used, but increasing the Sr concentration (y> 2) strongly inhibits this phase. It has also been established that the loss of Pb after synthesis depends on the initial Bi concentration. The loss of Pb decreases when the initial Bi content is lower.     

Modified atmosphere packaging of a mixed prepared vegetable salad dish

The aim of this study was to design a modified atmosphere package for a mixed vegetable salad consisting of 75 g of cut carrot, 55 g of cut cucumber, 20 g of sliced garlic and 50 g of whole green pepper. Respiration data of all the components were combined with film permeability data to predict package atmospheres and design optimal packages for experimental testing for improved shelf-life of the produce. The optimal package avoided minimum O₂ and maximum CO₂ tolerance limits, and chilling injury temperatures for any component. A pouch form package made of 27 mm low density polyethylene developed a modified atmosphere of 2.0–2.1% O₂ and 5.5–5.7% CO₂, which was beneficial for all components and provided better quality retention than other test packages.     

Final Drying of Whole Milk Powder in Vibrated-Fluidized Beds

Vibro-fluidized beds are widely used in drying sticky powders and agglomerated materials as milk powder. Using a vibro-fluidized laboratory scale dryer, this work is aiming at analyzing preliminarily the effect of its operational variables on the drying kinetics and characteristics of whole milk powder. The full-factorial design technique with three replications at the central point has been employed to generate data and correlations to quantify the effect of inlet air temperature, air flow rate, and vibration bed amplitude on the drying curves and the milk powder properties related to its faster reconstitution in water (as tapped density, Hausner cohesion ratio, agglomerate size distribution, and internal pore concentration). Results obtained are analyzed and discussed to identify the adequate operation condition for final drying whole milk powder in vibro-fluidized beds, assuring a high product quality.     

Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

暖通空调工程设计常见问题

通过对施工图审查工作进行总结，指出了暖通空调和防火防排烟设计中存在的问题及防火规范本身的一些不足。     

Structure and dynamics of dipolar fluids under strong shear

Molecular dynamical simulation has been carried out to investigate the structure and dynamics of a dipolar fluid under strong shear. Dipolar fluid consists of polarizable particles, which have an induced dipole moment in the applied field direction. Shear stress is perpendicular to the field direction. When shear stress is small, the flow has a flowing-chain structure. If shear stress increases to pass a critical value, flowing-chain structure changes to flowing layer structure. Each layer is parallel to the flow direction and shear direction. Within one layer, particles form strings in the flow direction.     

Evaporation and Evolution of Suspended Solution Droplets at Atmospheric and Reduced Pressures

Thermal history and solute precipitation behavior of suspended solution droplets of sodium chloride (NaCl), magnesium sulphate (MgSO₄), and zirconium hydroxychloride (ZrO(OH)Cl) evaporating at atmospheric and reduced pressures are studied. Experimental measurements on the variation of droplet diameter, solution concentration, and temperature during the evaporation period are presented and discussed. The results of solute precipitation behavior in solution droplets observed under an optical microscope are displayed and discussed. Results indicate that reducing the pressure (∼ 33 kPa) results in a change in the solution droplet evaporation rate, but the thermal histories of a particular solution droplet are similar at the atmospheric and reduced pressures. At atmospheric and reduced pressures used in this study, the d² law for solution droplets is valid at early stages of the evaporation and before the solute precipitation initiates. Drying of MgSO₄ and ZrO(OH)Cl solution droplets results in the formation of spherical particles, whereas drying of spherical NaCl solution droplets results in the formation of cubic particles.