面流消能近底紊动流速特性的研究(面流消能试验研究之一)

本文主要论述了面流消能五种典型流态近底紊动流速特性,总结出了近底时均流速和紊动强度沿程变化规律,提出了近底紊动流速可能出现的最大瞬时值及相应位置的计算公式。面流消能工程的下游防冲设计中考虑的主要水力参数之一是,消能段近底流速紊动可能出现的最大瞬时值及其相应的部位,但目前国内外研究成果较少。笔者通过水工模型试验重点研究了面流消能各典型流态近底流速及其紊动纵向分量沿程的变化规律,并提出了计算公式,为优化面流设计提供科学依据。     

集群系统与公用网互连的仿真模型和模拟算法

在讨论ＭＰＴ１３２７信令的集群移动通信系统与国内Ｎｏ．７信令的ＰＳＴＮ网间互连，帝现两种信令配合中，研究了集群系统的仿真模型和模拟算法，同时模拟出整个集群系统的工作情况，运行结果证实了所提方案的可行性与准确性。     

极尖断面为折线的四极透镜磁性能研究

对传统双曲线极尖的四极透镜进行了磁性能分析。在此基础上，提出了极尖断面为折线的四极透镜结构。磁场的数值分析以及测量结果表明：该结构产生的场梯度均匀，且具有磁场集中、磁场梯度高、便于加工和安装的对称性控制等优点。该结构的四极透镜已用于ＣＹＣＩＡＥ－３０回旋加速器和ＨＩ－１３串列加速器束流输运线之中     

Integration of a Malt Drying Model into a Malt Plant Scheduling Software

Malting is a very intensive, energy-consuming process and, from the point of view of energy, green malt drying is one of the most important operations. Double-deck kiln drying, a variant of single-deck kiln drying, is the most commonly used process, but it is usually manually controlled under empirical control actions. These are the reasons why a research project was carried out based on the computer modeling of these process operations including a software tool named CIMFOOD. A knowledge-based system (KBS) allowing the entire processing-plant dynamic behavior simulation and scheduling concerning thermal energy requirements was developed.     

Assessing the performance of intumescent coatings using bench‐scaled cone calorimeter and finite difference simulations

A method was developed to assess the heat insulation performance of intumescent coatings. The method consists of temperature measurements using the bench‐scaled experimental set‐up of a cone calorimeter and finite difference simulation to calculate the effective thermal conductivity dependent on time/temperature. This simulation procedure was also adapted to the small scale test furnace, in which the standard time–temperature curve is applied to a larger sample and thus which provides results relevant for approval. Investigations on temperature and calculated effective thermal conduction were performed on intumescent coatings in both experimental set‐ups using various coating thicknesses. The results correspond to each other as well as showing the limits of transferability between both fire tests. It is shown that bench‐scaled cone calorimeter tests are a valuable tool for assessing and predicting the performance of intumescent coatings in larger tests relevant for approval. The correlation fails for processes at surface temperatures above 750°C, which are not reached in the cone calorimeter, but are attained in the small scale furnace set‐up. Copyright © 2006 John Wiley & Sons, Ltd.     

β放射性气体浓度计的新分度方法

本文介绍β放射性气体浓度计的一种新的分度方法——泄漏元件排气法。其特点是一只元件可分度放射性气体浓度计的许多读出数(甚至是几个量程),操作方便。     

储层石蜡沉积预测技术研究与应用

在油田开发过程中 ,由于油藏温度、压力等条件的变化 ,高含蜡原油在近井带容易产生石蜡沉积 ,堵塞地层孔隙或裂缝 ,严重影响油田开采 ,尤其对于低渗油田 ,伤害特别严重。文中应用理想溶液理论、质量守恒和能量守恒等基本原理 ,建立更符合油田实际情况的油藏中石蜡沉积预测数学模型 ,开发一套方便实用的油藏中石蜡沉积预测软件系统FPOS1 0。在此基础上 ,应用室内实验数据和现场数据对吉林新民油田油井石蜡沉积情况进行预测和现场拟合 ,确定新民油田临界石蜡沉积半径为 2 5m ,快速、准确地为现场清防蜡措施提供理论依据。     

Discrete Modeling and Suggested Measurement of Heat Transfer in Gas-Solids Flows

This article presents a two-dimensional transient model for gas-solids flow and heat transfer through pipes using the coupled Computational Fluid Dynamics and Discrete Element Method approach. Numerical simulations have been conducted to examine the modification of fluid thermal structure due to the presence of particles in a pneumatic transport pipeline. Modeled results have demonstrated the key role of transversal motion of rebounding particles in the pipe cross section in altering fluid temperature. Further implementation of this modeling technique in air-drying processes is discussed and possible experimental methods for the measurement of in situ particle and fluid motion and temperature profile are cited.     

微机模拟处理pH络合滴定法研究——Ⅱ.终点确定方法和最佳实验条件模拟估计程序

本文利用简便的滴定过程模型,确立了微机模拟处理实验数据,方便、准确地求解络合滴定等当点的方法。设计了最佳实验条件模拟估计程序。该法测定Zn~(2+),Pb~(2+),Cu~(2+),Fe~(3+)结果的相对误差Δ<1％。pH=6-7时,测定Ca~(2+)的相对误差为-1.61％;σ<0.001mmol,(N=5)。