Hierarchical intelligent control with flexible AC transmission systems application

A novel hierarchical intelligent controller configuration is proposed using an artificial neural network as a control-mode classifier in the supervisory level and a set of pre-designed controllers in the lower level. Controller outputs are modified nonlinearly by the classifying signals in a structure resembling one artificial neuron with adaptively changed weights. The lower-level local controllers are implemented using neural networks. An illustrative example of this approach is based on the transient stabilization of a single-machine infinite-bus system studied in Flexible AC Transmission Systems (FACTS) research.     

Novel miniature integrated optical goniometers

A new principle and arrangement for directly determining the angle of incidence of an optical beam on an object are proposed and demonstrated. The novelty of the approach lies in the realization of a ‘smart object’, which extracts a portion of the incident beam's power into an optical waveguide attached to the object's surface or embedded in its body for converting the angle of incidence into the position of a guided beam with finite lateral extent. This ‘integrated optical light pointer’ beam is accomplished by means of creating additional degrees of freedom on the target in two different ways. While a first type is based on introducing spatial variations of the waveguide thickness, a second type makes use of a chirp of the grating periodicity. The feasibility for practical applications has been experimentally demonstrated by a direct comparison with a commercial high-resolution encoder, resulting in an r.m.s. error of <30′'. Measurements have been performed for chips fabricated based on replicated polycarbonate substrates and with no external optics, showing the great potential of this approach for realizing low-cost yet high-performance miniature goniometers.     

Quantitative evaluation of generator power control effect of FACTS controllers for power system stabilization

The advancement of power electronics technologies has significantly developed the power system stabilizing controllers. Quantitative as well as qualitative evaluation of their effectiveness in power systems is a matter of great importance for the feasibility investigation of these apparatus. In this paper, the possible control region of FACTS controllers with series and/or shunt configuration in a single machine to infinite bus system is formulated in the powerangle curve with a set of algebraic equations. The effectiveness of TCPST (Thyristor‐Controlled Phase Shifting Transformer), SSSC (Static Synchronous Series Compensator), and TCSC (Thyristor‐Controlled Series Compensator) for the improvement of the transient stability is evaluated quantitatively as a numerical example. The correctness of the proposed method has been confirmed by analysis based on the electromagnetic transients simulation with a detailed system model. © 2001 Scripta Technica, Electr Eng Jpn, 138(3): 43–51, 2002     

A novel robust current control approach using adaptive line enhancer for three‐phase current‐source active power filter

An effective system control method is presented for applying a three‐phase current‐source PWM converter with a deadbeat controller to active power filters (APFs). In the shunt‐type configuration, the APF is controlled such that the current drawn by the APF from the utility is equal to the current harmonics and reactive current required for the load. To attain the time‐optimal response of the APF supply current, a two‐dimensional deadbeat control scheme is applied to APF current control. Furthermore, in order to cancel both the delay in the two‐dimensional deadbeat control scheme and the delay in DSP control strategy, an Adaptive Line Enhancer (ALE) is introduced in order to predict the desired value three sampling periods ahead. ALE has another function of bringing robustness to the deadbeat control system. Due to the ALE, settling time is made short in a transient state. On the other hand, total harmonic distortion (THD) of source currents can be minimized compared to the case where ideal identification of the controlled system can be made. The experimental results obtained from the DSP‐based APF are also reported. The compensating ability of this APF is very high in accuracy and responsiveness although the modulation frequency is rather low. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(1): 50–61, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20014     

Modeling Condensation and Evaporation on Fruit Surface

Rewarming of fruits and vegetables after cooling is characterized by heat and mass transfer processes, which leads commonly to condensation of water on the produce surface at temperatures below the dew point. This effect may affect the produce quality due to microbial growth at unfavorable environmental conditions. The amount of condensed water is a function of the produce surface temperature and of the surrounding conditions as air temperature, air humidity, and air flow. Under practical conditions, both the warming and the condensation are strongly affected by the packaging system used. Depending on the flow conditions close to the produce surface, parameters of heat and mass transfer under laboratory conditions were measured. A mathematical model was developed for the determination of the amount of condensed water on fruit surfaces, its reevaporation, and its total dwell time dependent on the environment air conditions. The model describes the heat and mass transfer processes on single fruits. The process of diffusion of humidity in air and proceed of surface temperature is the basis for the model.     

Characterization of the flow behaviour of sausage emulsions with a simple tube viscometer

A specially designed tube viscometer was used to measure apparent viscosity during flow of Bologna type sausage emulsions moving through a pipe. Emulsions varied in fat content (from 21.8 to 44.3%) and in moisture/protein ratio (from 3.7 to 5.6), and the effects of added sodium chloride, sodium diphosphate, starch and blood plasma were investigated in a 36% fat, 3.7 moisture/protein emulsion.
The shear stresses determined as a function of shear rate were fitted by a power law. Yield stress of the emulsions was negligible relative to the applied stress. However, inspection of the flow profiles indicated that considerable slip of the sausage emulsion occurred at the pipe wall. Both emulsion flow and slip contribute to overall flow behaviour, so a kind of effective viscosity is determined. Intrinsic rheological properties and wall slip will both be affected by the composition of the sausage emulsion.     

Modeling of a power electronic converter for EMC in the conduction emission frequency band

With the advancement of high‐frequency switching devices, electromagnetic interferences (EMI) have become problems in power electronic converter designs. It is necessary for an electromagnetic compatibility (EMC) design to prospect and consider its possible EMI levels. This paper describes how to compute effects from a power converter to an object point to reduce conduction EMI noises effectively by an appropriate design. Modeling techniques for converter elements are discussed for a model in the conduction emission frequency band by the parameter tuning method and for line constants by an analytical derivation. Then a derived model is simulated for harmonic distributions of loop currents and their magnetic fields. © 2002 Scripta Technica, Electr Eng Jpn, 139(1): 44–50, 2002: DOI 10.1002/eej.1145     

Change of characteristics of desulfurization and denitrification by combustion flue gas composition and electrode configuration under pulsed corona discharge

Laboratory-scale and parametric experiments of SO₂ and NO_x removal from the simulated combustion gas by pulsed corona discharge have been performed by changing the combustion gas composition and temperature, the electrode configuration of plasma reactor, and the polarity of high-voltage electrode. The following results are obtained: 1) the higher the concentration of H₂O and O₂, the higher the efficiency of desulfurization and denitrification at the same specific input; 2) the pulsed corona discharge with a voltage pulsewidth as short as 200 ns of negative polarity shows the possibility to attain almost 90 percent deSO_x and deNO_x efficiency at the specific discharge input of 20 J/g, which is almost the same as the specific input in the electron-beam process; 3) the deNO_x characteristics show a little temperature dependence in the range of 70 to 130°C, but the deSO_x efficiency increases rapidly in the temperature region below 100°C suggesting the thermochemical dependence of deSO_x reaction; 4) when desulfurization and denitrification proceed, the white dendritic powder deposits on the plasma reactor whose composition is identified to be 49 mol% (NH₄)₂SO₄ and 47 mol% of 2NH₄NO₃ · (NH₄)₂SO₄, and the ratio of SO₂, NO and NH₃ of the deposit is almost equal to that of supplied gas.