邢钢180 m2烧结机提高混合料温度的实践

介绍了邢钢180 m^2烧结机投产以来,在提高混合料温度方面所采取的主要措施.该厂通过提高生石灰质量、采用蒸汽预热混合料、在混合机中加热红泥浆等,改善了混合料的透气性,进而提高了烧结矿产、质量.     

Understanding silica-supported metal catalysts: Pd/silica as a case study

Supported metal catalysts, particularly noble metals supported on SiO₂, have attracted considerable attention due to the importance of the silica–metal interface in heterogeneous catalysis and in electronic device fabrication. Several important issues, e.g., the stability of the metal–oxide interface at working temperatures and pressures, are not well-understood. In this review, the present status of our understanding of the metal–silica interface is reviewed. Recent results of model studies in our laboratories on Pd/SiO₂/Mo(1 1 2) using LEED, AES and STM are reported. In this work, epitaxial, ultrathin, well-ordered SiO₂ films were grown on a Mo(1 1 2) substrate to circumvent complications that frequently arise from the silica–silicon interface present in silica thin films grown on silicon.     

微波合成无机纳米材料的研究进展

微波加热作为一种合成纳米材料的新方法，近年来得到飞速发展。介绍了微波加热原理，阐述了微波合成无机纳米材料的一些研究进展，主要是液相微波加热在制备金属氧化物和金属硫化物纳米材料以及微波烧结在合成陶瓷材料的应用，并对该领域未来作了一些展望。     

马钢二烧结配料计算机控制系统

阐明了马钢二烧结配科计算机控制系统的目的、控制形式、控制原理；根据烧结配料控制对象的特点对信号采样和控制算法进行了探讨；提供了系统的主要硬件结构，软件功能和程序框图。     

片式多层陶瓷微波谐振器

介绍了片式陶瓷微波谐振器的工艺过程、谐振器的结构以及结构对谐振器参数的影响,谐振器与外电路的耦合采用耦合间隙的方法与谐振单元在同一层内实现,这种新结构既可给制备工艺带来方便,又可减少工艺所带来的误差。用多层陶瓷工艺技术,用高介电常数、低温烧结微波陶瓷实现了中心频率为1GHz,有载品质因数大于80的试验双端口多层微波谐振器。微波谐振器体积小,整个谐振器的尺寸为7mm×2mm×1mm,适用于表面贴装技术。     

天然气空气绝热转化制合成气催化剂研究

制备了天然气空气绝热转化催化剂,采用固定床反应器进行稳定性评价试验,对反应前后的催化剂进行了分析表征。结果说明,天然气和空气绝热转化反应放热形成的高温对催化剂有烧结作用,使催化剂晶体结构发生了变化,起活性作用的金属镍和氧化铝载体转化为镍铝尖晶石结构的物质。进一步的试验表明,在1050～1300℃的温度可以把催化剂的晶体结构改变。     

烧结NdFeB合金中的夹杂物

使用金相显微镜、扫描电镜及Ｘ射线能谱和波谱观察并分析了ＮｄＦｅＢ烧结材料中夹杂物的形态、数量和组成。磁粉制备后立即烧结的ＮｄＦｅＢ磁体中的夹杂物是氧化钕；而在不同环境条件下放置后的ＮｄＦｅＢ粉再烧结的材料中发现，除了氧化钕的夹杂物外，还有钕的氮化物及钕的氮氧复合夹杂物。同时还论讨了这些夹杂物对于ＮｄＦｅＢ材料磁性能的影响。     

Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.     

气力输送在烧结电除尘输灰系统中的应用

针对烧结厂烧结电除尘灰的工况特性，介绍了输送烧结电除尘灰的正压气力输灰系统的特点、组成，还对在调试和试运行过程中遇到的故障进行了分析并制订了解决措施。