WC/Ni60真空熔烧涂层的组织结构特性

研究了真空熔烧WC Ni60复合涂层的显微组织结构特性 ,并测定了沿层深方向的显微硬度分布。研究结果表明 ,涂层与母材 4 5钢在界面处形成牢固的冶金结合 ,界面两侧的显微硬度呈连续性分布     

Calcium addition in straw gasification

The present work focuses on the influence of calcium addition in gasification. The inorganic-organic element interaction as well as the detailed inorganic-inorganic elements interaction has been studied. The effect of calcium addition as calcium sugar/molasses solutions to straw significantly affected the ash chemistry and the ash sintering tendency but much less the char reactivity. Thermo balance test are made and high-temperature X-ray diffraction measurements are performed, the experimental results indicate that with calcium addition major inorganic-inorganic reactions take place very late in the char conversion process. Comprehensive global equilibrium calculations predicted important characteristics of the inorganic ash residue. Equilibrium calculations predict the formation of liquid salt if sufficient amounts of Ca are added and according to experiments as well as calculations calcium binds silicon primarily as calcium silicates and less as potassium calcium silicates.     

Effect of carbide additions on grain growth in TiC−Ni cermets

The growth of carbide particles in TiC-XC-2 vol.% Ni and TiC-XC-30 vol.% Ni alloys, where X=Zr, Cr, W, Ta and Mo, was fitted to an equation of the form d³-d_o ³=Kt. The grain growth behavior during liquid phase sintering at 1673K decreased markedly with the addition of Mo₂C or WC, changed little for TaC, and increased with the addition of ZrC or Cr₃C₂. The grain contiguity decreased with increasing Ni content in the TiC−Mo₂C−Ni alloy and was greater in the alloys with smaller growth rate constant. Consequently, the effect of carbide addition on the grain growth of 2 vol.% Ni alloys was found to be similar to that of 30 vol.% Ni alloys. The grain growth mechanism could be explained by the effect of contiguous carbide grain boundaries in restricting the overall grain growth, as well as the area of the solid/liquid interfaces in the alloy by the usual solution/reprecipitation model.     

短纤维增强透气性莫来石/铁(A3S2/Fe)复合材料烧结特性的研究

本文研究了A₃S₂/Fe复合材料的烧结特性、透气性和纤维增强效果,分析了烧结过程中材料宏观结构和微观组织的形成机理.实验结果表明:纤维增强A₃S₂/Fe复合材料在900～1000℃具有良好的烧结性能,烧成后表层存在一定厚度的硬化层;纤维增强效果显着.材料抗压强度达17～23MPa,相对透气系数为4.30～9.69cm3/(cm2·s·atm).已能满足实际应用的需要.     

高频MnZn功率铁氧体烧结工艺研究

按照氧化物陶瓷工艺对高频MnZn功率铁氧体烧结工艺条件进行了研究。烧结温度越高，晶粒越大，晶界越薄，电阻率越低，磁芯损耗越大，起始磁导率和烧结密度分别在1240℃和1230℃达到最大值。延长保温时间，可以使晶粒充分生长，晶界变薄，电阻率减小，损耗增大。保温3h后，起始磁导率和烧结密度均可达到最大值。氧分压越低，材料起始磁导率越高，电阻率越小，损耗越大，但氧分压低于5％后烧结密度不再继续增加。     

纳米陶瓷的制备

纳米陶瓷材料可显著降低材料的烧结致密化程度,节约能源;并可改善陶瓷材料的性能,提高其使用可靠性。主要介绍了纳米陶瓷的制备方法,包括纳米陶瓷粉体的制备、成型和烧结。     

首钢烧结生产技术近年来的发展与进步

近几年来，炼铁厂烧结生产通过改进工艺技术和设备，使烧结产质量稳步提高，在满足高炉生产需要的同时，实现了低耗、清洁的目标。     

马钢三烧低SiO2烧结的生产实践

马钢三烧通过采取有效措施，在保证烧结矿产质量稳步提高的前提下。使SiO2含量逐步降低，取得了较好的效果。     

烧结硬化用低合金钢粉

本文将介绍三种不同成分的低合金钢粉。在混入2 0%铜和不同石墨含量的条件下,对该三种粉进行了试验评定。试件的密度为6 9g/cm3,在氮氢混合气氛中于1120℃下烧结25min,在炉内冷却带650～400℃温区的冷却速度为0 4或1 5℃/s条件下,对烧结态和回火后试件的力学性能进行了测试。回火条件为200℃下保温60min。在一定的冷却速率和碳含量条件下,各种钢粉烧结后的硬度可高达40HRC。回火后,硬度仍可以保持在30HRC以上。     

烧结原料场大面积扬尘的控制措施

针对烧结原料场大面积扬尘的情况。提出了综合治理措施。着重对适合于烧结用粉状物料的扬尘抑制剂进行了研究。