Surface tailoring of an ethylene propylene diene elastomeric terpolymer via plasma‐polymerized coating of tetramethyldisiloxane

In the research presented here, we explore the use of a low‐energy plasma to deposit thin silicone polymer films using tetramethyldisiloxane (TMDSO) (H(CH₃)₂? Si? O? Si? (CH₃)₂H) on the surface of an ethylene propylene diene elastomeric terpolymer (EPDM) in order to enhance the surface hydrophobicity, lower the surface energy and improve the degradation/wear characteristics. The processing conditions were varied over a wide range of treatment times and discharge powers to control the physical characteristics, thickness, morphology and chemical structure of the plasma polymer films. Scanning electron microscopy (SEM) shows that pore‐free homogeneous plasma polymer thin films of granular microstructure composed of small grains are formed and that the morphology of the granular structure depends on the plasma processing conditions, such as plasma power and time of deposition. The thicknesses of the coatings were determined using SEM, which confirmed that the thicknesses of the deposited plasma‐polymer films could be precisely controlled by the plasma parameters. The kinetics of plasma‐polymer film deposition were also evaluated. Contact angle measurements of different solvent droplets on the coatings were used to calculate the surface energies of the coatings. These coatings appeared to be hydrophobic and had low surface energies. X‐ray photoelectron spectroscopy (XPS) and photoacoustic Fourier‐transform infrared (PA‐FT‐IR) spectroscopy were used to investigate the detailed chemical structures of the deposited films. The optimum plasma processing conditions to achieve the desired thin plasma polymer coatings are discussed in the light of the chemistry that takes place at the interfaces. Copyright © 2004 Society of Chemical Industry     

Cover Picture: Toward Large‐Scale Alignment of Electrohydrodynamic Patterning of Thin Polymer Films (Adv. Funct. Mater. 15/2006)

By integrating lithography and self‐assembly via electrohydrodynamic instabilities, Russel and co‐workers are able to guide initially flat polymer films to evolve into periodic arrays of pillars over regions much greater in extent than their natural domain sizes, as detailed on p. 1992. Novel structures that involve a combination of linear ridges and pillars are also produced, mainly as as result of the dynamic merging among preformed pillars. To pattern thin polymer films via electrohydrodynamic instabilities, we design and utilize two different kinds of mask patterns to guide pillars into alignment over regions much greater in extent than their natural domain sizes. First, narrow protruding ridges that intersect to form regular patterns on the mask trigger the growth of pillars beneath. Later, square and triangular packings of pillars develop in the regions enclosed by those ridges, preserving the registry from one domain to the next over a much larger area than within individual domains in unpatterned portions of the mask. Second, small square protrusions that are prealigned into a large regular array on the mask guide the formation of square packings of pillars in domains that conform to the mask, forming a large array of pillars. Novel structures involving a combination of linear ridges and pillars are also produced mainly due to the dynamic merging among preformed pillars. Finally, we find vertex symmetry of the mask pattern is necessary for generating and preserving ordered patterns on the polymer film.     

Luminescence Characterization of Mg Doped Y2O2S:Ti Long Afterglow Phosphor

Y1.94-xMgxO2S:0.06Ti (0≤x≤0.10) phosphors with long afterglow were synthesized by solid state reaction route. The photoluminescence spectra, decay curves, thermoluminescent spectra and chromaticity coordinate curves were investigated. The results show that the luminescence intensity of Y1.94-xMgxO2S:0.06Ti (0≤x≤0.10) phosphors decrease gradually with increasing Mg2 ion content, and the shape of luminescence spectra and chromaticity coordinate change as well. Furthermore, two thermoluminescent peaks in single Ti-doped Y2O2S sample are found at 91.8 and 221.5 ℃, respectively. Nevertheless, significant different spectra were found for the Mg, Ti co-doped Y2O2S samples that three thermoluminescence peaks appear at 52.3, 141.7 and 226.8 ℃, respectively. These results indicate that the co-doped Mg ion changes the inherent trap depth of single Ti-doped Y2O2S:Ti phosphor, and induces simultaneously a new trap level in the Y1.94-xMgxO2S:0.06Ti phosphor. Based on the analysis of thermoluminescent spectra, photoluminescent spectra, decay curve and crystal structure defect, it was proposed that the varied structure defect and introduced new trap level by the doped Mg2 ions should be responsible for reducing luminescence intensity and varying color in the Y1.94-xMgxO2S:0.06Ti phosphor.     

Kinetic investigation of the carbothermal reduction of an Iranian clay

The kinetics of the carbothermal reduction of clay under argon atmosphere has been investigated by the X-ray diffraction method. The clay-carbon (excess) mixture was formed into 2 cm diameter disks of different thicknesses. Experimental data evidences the significant effect of sample thickness on the reaction rate at 1400 °C. Decreasing thickness promotes mullite dissociation and formation of SiC and alumina powders. Mathematical modeling of the reaction system showed the gas diffusion in the Knudsen regime through the pellet to be the rate controlling step. Diffusivity of CO and reacted core tortuosity factor have been calculated.     

Phase equilibrium in solutions of star-shaped macromolecules: an improved Okada-Numasawa model

The two-region Okada-Numasawa model for solutions of star-shaped polymers has been improved by means of a change in the integration order and introduction of a concentration-dependent and molar-mass-dependent Flory-Huggins interaction parameter (the second and third approximations of the Flory-Huggins theory). To overcome calculation difficulties, a special algorithm for computing coexistence curves of polymeric systems with an UCST has been used. The agreement between the experimental and calculated coexistence curves for the star-shaped polystyrene (PS)-cyclohexane system has been improved: the difference between T_cs is ∼0.33 K against ∼12 K as given by the original model.     

四倍频Nd：YAG激光在高压氢气中的喇曼频移研究

利用Nd:YAG固体激光器四倍频输出(266nm)在高压H₂中的受激喇曼散射获得多波长的激光输出。当泵浦能量一定时,通过改变H₂压力得到了最佳的能量输出,299nm波长的激光能量为3mJ,341nm波长的激光能量输出为6.1mJ,398nm波长的激光能量输出为2.8mJ,239nm波长的激光能量输出为0.8mJ,同时在477nm,595nm,218nm,200nm波段也有能量输出。     

用于泵浦固体激光器的激光二极管线阵的输出特性

从实验上测量了激光二极管线阵的输出特性,研究了温度、电流对输出功率、光谱特性,以及偏振特性的影响,为设计全固态激光器提供有益的参考。     

The Problem of Estimating the Uncertainty of the Fixed Point Temperature Due to the Presence of Impurities

The main problems in estimating the uncertainty due to the presence of impurities in the material: the absence in the documents of a unique definition of the quantity being measured – the fixed point temperature, the lack of agreed methods of realizing the fixed points and the insufficient justification of the equations used for the estimate, are analyzed. The results of a measurement of the melting point of gallium are presented, which differ in the conditions in which they were realized – with one and two liquid-solid interfaces and different solidification conditions, are presented. The reasons for the considerable difference between the values of the temperatures obtained in these experiments are discussed.     

Sol-gel preparation of a di-ureasil electrolyte doped with lithium perchlorate

Solid polymer electrolytes (SPEs) synthesized by the sol-gel process and designated as di-ureasils have been prepared through the incorporation of lithium perchlorate, LiClO₄, into the d-U(2000) organic-inorganic hybrid network. Electrolytes with lithium salt compositions of n (where n indicates the number of oxyethylene units per Li⁺ ion) between ∞ and 0.5 were characterized by conductivity measurements, cyclic voltammetry at a gold microelectrode, thermal analysis and Fourier transform Raman (FT-Raman) spectroscopy. The conductivity results obtained suggest that this system offers a quite significant improvement over previously characterized analogues doped with lithium triflate [S.C. Nunes, V. de Zea Bermudez, D. Ostrovskii, M.M. Silva, S. Barros, M.J. Smith, R.A. Sá Ferreira, L.D. Carlos, J. Rocha, E. Morales, J. Electrochem. Soc. 152 (2) (2005), A429]. “Free” perchlorate ions, detected in all the samples examined, are identified as the main charge carriers in the sample that yields the highest room temperature conductivity (n = 20). In the di-ureasils with n ≤ 10 ionic association is favoured and the ionic conductivity drops.     

Cover Picture: Light‐Emitting Organic Solar Cells Based on a 3D Conjugated System with Internal Charge Transfer (Adv. Mater. 22/2006)

The cover image illustrates the dual photovoltaic and electroluminescence function of a single‐layer device based on a thienylenevinylene–triphenylamine with internal charge transfer (ICT), as reported by Cravino, Roncali, and co‐workers on p. 3033. The material forms an organic glass with isotropic electronic properties while ICT leads simultaneously to an extension of the photoresponse to the red and to an increase of the open circuit voltage. The use of an additional layer of C₆₀ further improves the photovoltaic. Images of the sun and moon courtesy NASA/JPL–Caltech.