奎宁印迹聚合物的吸附与识别特性的研究

以奎宁为模板分子 ,利用分子印迹技术合成了一种新型的类似于人工受体的印迹聚合物 ,研究了它对奎宁和其它底物的吸附特性和选择性识别能力 ,并对其固相萃取性能做了初步的研究。     

MB8镁合金薄板的搅拌摩擦焊

针对我国航空航天工业常用的MB8镁合金。采用搅拌摩擦焊工艺进行焊接，对其焊缝的成形特点、组织特征和力学性能进行分析。结果表明，采用搅拌摩擦焊焊接镁合金效果良好。     

Properties of Carbopol Solutions as Models for Yield-Stress Fluids

ABSTRACT: The effect of pH on the non-Newtonian viscosity (η)of aqueous Carbopol 940 solutions is presented with high resolution (pH increments about 0.4) between pH = 2.8 and 12.7. Aqueous NaOH was used to adjust pH of 1.48 wt % Carbopol solutions. A Contraves viscometer was used to measure steady-flow shear stress at known shear rate (γ) over the range γ= 8 to 195 s⁻¹. Yield stresses and shear-thinning η(γ) were observed. Data were fitted with a Herschel-Bulkley model, whose parameters (including yield stress) were expressed as functions of pH. Comparisons were made of η(γ) to the dynamic viscometric properties η'(ω) and η*(ω) for comparable ranges of γ and frequency (ω): A fairly close match was found between η and η* but η«η'. pH dependence included previously unreported extrema of h(pH) in the range of pH = 6.2 to 6.6. Because of sensitive control of rheological properties with pH, Carbopol solutions can be used to mimic a great range of shear-thinning and yield-stress behavior that should make them useful for model studies directed toward process and equipment design and evaluation.     

熔融-固相缩聚法中固相聚合对聚乳酸合成的影响

以L 乳酸单体为原料 ,熔融 -固相缩聚法合成了聚乳酸 ,重点研究了固相聚合的工艺条件。结果表明 ,绝对压力 60Pa ,氯化亚锡为催化剂 ,分段控温 ,可使聚乳酸的粘均分子量提高到固相聚合反应前的 5 3倍。通过对固相聚合产物的结晶度和熔点的分析 ,探讨了固相聚合的机理。     

Acoustic emission method for research and control of friction pairs

One of the new physical methods that provides much information about the processes going on in a friction contact zone in real time is acoustic emission (AE). Basic experimental results of AE in friction are presented and analysed. Using AE signals we can get an indication about the state of the friction processes, about the quality of solid and liquid layers on the contacting surfaces in real time, sometimes about intensity of wear, changing of wear and friction regimes and so on. The influence of sliding velocity, load, roughness and some physical and mechanical properties of the body on the parameters of AE are also given. Some attention to the practical implementation of these techniques for control of capability for work of friction pairs in real conditions are given. Modern methods and devices enable condition monitoring of sliding and rolling bearings.     

Grain Growth Behavior of 5Cr21Mn9Ni4N Steel Micro-Alloyed by Rare Earth

Grain growth behavior of 5Cr21Mn9Ni4NRE steel was experimentally studied at various solid solution treatment temperatures and holding for different times. The experimental results show that the 5Cr21Mn9Ni4NRE steel has the feature of sharp austenite grain coarsening after solid solution treatment at the temperature above 1150 ℃. RE added in the steel has the benefit to restrain grain growth and increase grain growth activation energy.     

Exit effect on hydrodynamics of the internal circulating fluidized bed riser

This is the first time an extensive investigation has been carried out regarding the effects of riser exit geometry on pressure drop and solid behaviour inside the Internal Circulating Fluidized Bed (ICFB) riser, using different riser exit geometries at several operating conditions.The Radioactive Particle-Tracking (RPT) technique was used for solid concentration measurements and solid residence time distribution at the exit zone. Experiments were conducted using Geldart B particles, in the gas superficial velocity range of 4 to 10 m/s. Axial solid hold-up, solid residence time distribution in the exit zone, and the reflux ratio factor k_m, (defined earlier by [E.H. Van der Meer, R.B. Thorpe, J.F. Davidson, Flow patterns in the square cross-section riser of a circulating fluidized bed and the effect of riser exit design, Chem. Eng. Sc. 55 (19) (2000) 4079-4099]), were the main criteria used to investigate the impact of gas-solid separator devices implemented at the ICFB riser exit.Solid residence time distribution results and axial solid hold-up profiles provided clear evidence that the separator device at the riser exit strongly influences the hydrodynamic structure of the ICFB riser. The V-shaped riser exit geometry was found to be the optimum of all the configurations studied.     

负载型固体碱催化合成亚苄基丙酮

研究了用固体碱 KOH/Al_2O_3催化合成苯叉丙酮,确定了合成的最佳工艺条件:n(苯甲醛)∶n(丙酮)=1∶4.催化剂用量2g,催化剂最佳负载量12mmol/g,反应温度40～45℃,反应时间为3h,产率达88%以上。     

Impact of the addition of an enzyme pool on an activated sludge system treating dairy wastewater under fat shock loads

BACKGROUND: The application of lipase‐rich enzyme pools (such as the crude solid enzymatic preparation (SEP) obtained from Penicillium restrictum solid‐state fermentation of agro‐industrial wastes) to activated sludge systems may be an effective strategy for preventing various operational problems. The continuous addition of SEP to the treatment system can become cost‐prohibitive when in situ production and/or storage are factored in. The application of SEP to high‐fat wastewater treatment would only be justified as an emergency measure, such as a sudden increase in the fat content of the bioreactor influent. Therefore, the primary objective of this work was to investigate the efficiency of a crude SEP during fat shock loads, simulated through the periodic addition of dairy industry waste containing high fat concentrations to the feed stock of an activated sludge system, operated in continuous mode. RESULTS: The test bioreactor exhibited a higher average chemical oxygen demand (COD) removal efficiency than the control bioreactor (83% for control and 90% for test) and the fat accumulation in the biological flocs of the test bioreactor was 3.2 times lower than that in the control bioreactor. Turbidity was also lower in the effluent of the test bioreactor (123 and 66 FTU in control and test, respectively) and it had a shorter recovery time between shock loads, especially when the interval between loads was shorter than one month (biweekly and weekly shock loads). CONCLUSION: The addition of SEP during fat overloads in the reactor feed maintained efficient COD removal in the test bioreactor for 270 days without any operational problems. Copyright © 2008 Society of Chemical Industry     

Non-pinched, minimum energy distillation designs

Non-pinched, minimum energy solutions are important class of distillation designs that offer the potential advantage of a better trade-off between capital investment and operating costs. In this paper, two important tasks associated with non-pinched distillation designs are studied. Thus the novel contributions of this work to the literature are

(1) A comprehensive methodology for finding non-pinched minimum energy designs.

(2) Understanding of the reasons for the existence of non-pinched distillation designs.

It is shown that the recent shortest stripping line distance approach of Lucia et al. [Lucia, A., Amale, A. and Taylor, R., 2007, Distillation pinch points and more. Comput Chem Eng, available on-line] is capable of systematically and reliably finding non-pinched, minimum energy distillation designs. In addition, we provide an understanding of the reasons behind the existence of non-pinched designs, which include trajectories that follow unstable branches of a pinch point curve in azeotropic systems, the inherent looping structure of trajectories in hydrocarbon separations, and the presence of ancillary constraints in multi-unit processes like extraction/distillation. Several distillation examples are studied and many numerical results and geometric illustrations are presented that show the shortest stripping line distance methodology is indeed a powerful and systematic tool for computing non-pinched, minimum energy designs and that support the underlying reason we provide for the existence of non-pinched designs.