螺旋CT的三维空间面皮参数平面化方法*

将三维空间面皮转换为二维平面可以使获取面皮特征、颅骨与面皮的关联信息更方便。通过改进的轮廓线提取方法剔除原始切片冗余数据,对重构得到的面皮数据进行空间坐标系的规范,并以最近邻区域(NNR)划分方法将空间面皮的点云数据点集化,最后结合新划分的平面点数据集的特点提出了线性插补的参数平面化方法和基于链表的参数平面化方法。实验证明两种方法的效果良好,验证了其正确性和可行性。     

海底管线防冲刷技术试验研究

海底冲刷现象严重威胁着海底管线的安全运营.该文从海底管线冲刷机理入手,根据海底管线防冲刷技术的基本原理,提出了仿生防护措施--"人工草"固定法,并结合现有工程项目进行了试验研究,结果表明该方法可以有效地解决海底冲刷造成的管道悬空问题,为海底管线工程的设计、施工和维护提供了指导性的参考.     

Effect of the Three Gorges Reservoir on vertical distribution of suspended sediment concentration and estimation accuracy of depth-average concentration in downstream reaches

The sediment regime in the middle Yangtze River has been significantly changed from quasi-equilibrium to nonequilibrium since the impoundment of the Three Georges Reservoir (TGR). To understand the effects of the TGR on vertical distribution of suspended sediment concentration (SSC) and estimation accuracy of mean concentration, vertical sediment concentration and flow velocity data at the Shashi and Jianli hydrological stations in the reach before and after the impoundment were collected. Comparisons and analysis of vertical profiles of SSC before and after the TGR impoundment show that after the impoundment of the TGR, due to the coarsening of sediment particle size, the reduction in sediment load, and the significant decrease in sediment saturation, the vertical distribution of SSC in the downstream reaches became more uneven under medium and low water flows, which was reflected in the vertical gradient and the fluctuation degree of SSC significantly increased. In addition, the depth-average sediment concentrations were calculated by the selected-point method and the mean values calculated by the “multi-point method” were regarded as the “true mean” to evaluate the accuracy of the mean value calculated by the “few-point method.” It was found that the relative errors for the selected-point method were mainly positive before impoundment but mainly negative after impoundment. Additionally, the correction factors of one-point, two-point, and three-point methods and the position of the near-bed substituted point for the five-point method were given to reduce the error when the point measurements were used to calculate the depth-average sediment concentration in the downstream reaches.     

半球型动压气体轴承陀螺电机设计及性能测试

针对高精度三浮陀螺用半球型动压气体轴承陀螺电机的启停寿命问题,对半球型动压气体轴承的设计理论以及保证轴承在电机工况下能可靠启停的一些关键技术进行研究.其中轴承间隙和螺旋槽结构参数是影响轴承可靠启停以及其力学性能的关键因素,将螺旋槽结构参数作为变量,通过改变变量参数来分析轴承力学指标的变化趋势,得出螺旋槽各关键参数与轴承刚度的关系曲线;通过有限元法仿真分析并校核了电机在工况下轴承的稳定性,证明了轴承间隙参数设计合理.在此基础上研制了半球型动压气体轴承陀螺电机样机,并进行专项的电机启停寿命试验,启停次数满足陀螺不少于3 000次指标要求,满足高精度三浮陀螺的使用要求.     

考虑安装错位的弧齿锥齿轮小轮齿面再设计

为保证弧齿锥齿轮副在实际工况下具有良好的齿面印痕与啮合状态,研究安装错位的识别技术以及错位条件下的齿面再设计技术.分析可导致相同齿面印痕的多种安装错位组合之间的关系;提取齿面印痕的数值特征,以两接触轨迹曲线的偏差和最小为目标函数,采用优化方法识别当量安装错位;基于局部综合法,根据当量安装错位重新设计小轮的齿面.以一对弧齿锥齿轮副为例,比较实际安装错位与当量安装错位作用下的小轮再设计齿面的差曲面,验证了该设计方法的正确性和有效性.     

Characteristics of Left-Right Spiral Hollow Cylindrical Roller

Based on new rolling-sliding compound bearings,the wear between the one-way spiral hollow cylindrical roller and the ribs of the inner and outer ring of rolling-sliding compound bearings is reduced by innovational structural design. A new left-right spiral hollow cylindrical roller is proposed to replace the one-way spiral hollow cylindrical roller. The finite element analysis models of ordinary cylindrical rollers,one-way spiral hollow cylindrical rollers and left-right spiral hollow cylindrical rollers are respectively established by ABAQUS.The axial displacement of their center mass and the stress distribution of left-right spiral hollow cylindrical rollers are compared and analyzed. Theoretical study results show that this new left-right spiral hollow cylindrical roller not only inherits the advantages of one-way spiral hollow cylindrical rollers,but also avoids the axial offset and the serious wear of the one-way spiral hollow cylindrical roller. And the theory research conclusion is verified by the experiment. The left-right spiral hollow cylindrical roller has the advantages to overcome boundary stress concentration like logarithmic convex roller. The rolling-sliding compound bearings equipped with the new rollers can be better to adapt to the impact of vibration load.     

弧齿锥齿轮有限元建模与接触分析

为了使有限元软件能够对齿面微米量级变化的齿轮进行分析,提出了基于高精度建模的有限元分析方法。将齿面的理论计算公式转化成数值计算算法,按照有限元理论和有限元软件的编程语法将齿轮实体进行节点坐标求解和网格单元划分,可以求得一对装配好的有限元齿轮模型。高精度建模的高重合度弧齿锥齿轮算例中,将有限元计算结果与实验结果对比,发现两者的一致性:弯曲应力曲线形状一致,变化规律相近;接触印痕区域一致,变化趋势相同。高精度建模有限元分析能够清晰的反映齿面微米量级改变导致的印痕和应力的变化。     

钢球全表面展开机构模型建立及其运动分析

针对镜面钢球缺陷检测装置中的球体全表面展开问题,建立展开机构接触模型并对球体运动进行分析,证明展开机构结构合理可行。首先由坐标变换建立数学模型,基于Matlab对模型空间接触位置进行计算,将展开运动合理简化,得到钢球和展开轮之间转动的同步关系;其次,对展开运动过程进行等效变换,寻找传动过程中能使钢球稳定展开的最优参数关系;最后,依据迭代法对球面上点的运动轨迹进行数值仿真,获得其具体规律为偏角固定的螺旋线。最终结果表明展开机构能够实现球体的全表面展开。     

粉煤灰悬浮胶体的悬浮稳定性实验研究

针对煤矿生产中粉煤灰防(灭)火材料管路输送的管路阻塞问题,选择SC1,SC2,SC3,SC4,SC5,SC6,SC7和SC8共8种悬浮剂,配制成4种质量分数分别为0.5%,1.0%,1.5%和2.0%的粉煤灰悬浮胶体,采用沉降分析方法,研究其悬浮稳定性。结果表明:各粉煤灰悬浮胶体沉降速率出现类似"L型"变化,沉降到一定时间均达到平衡状态;悬浮剂可以减小粉煤灰悬浮体沉降速率变化,质量分数越低,初始沉降速率越大,质量分数越高,沉降速率变化越小;同时也可增大粉煤灰悬浮率,增加悬浮胶体的稳定性。     

倾斜波束非对称SAARS微带天线设计简

A circularly polarized microstrip antenna with the tilted beam of 30° through the asymmetrical structure combing the single-arm archimedean spiral antenna with the helix antenna is constructed in order to make the beam tilted. The bandwidth, tilted beam, and radiation characteristics have been improved through the width optimization and coaxial feed line selection. This antenna can realize the directional radiation of circularly polarized microwaves in a definite frequency band and has a bandwidth of 16.7％ (for Voltage Standing Wave Ratio(VSWR)<2, Axis Ratio(AR)<3dB and the tilted beam of 30°) in the condition of the vertical aperture external excitation with a coaxial feed line. Simulated and measured results show that this antenna has a wideband, high gain, and tilted beam with circularly polarized microwaves.