ca油田稠油油藏系统保护油气层研究

针对ca油田多层状砂泥薄互层稠油油藏的特点,开展了热采和非热采条件下储层变化特征研究、钻井和固井过程入井液的研究、采油工艺技术等系统保护油气层研究,了解各种变化的作用过程和原因,有效地预防现场施工中可能发生的储层伤害,从而达到储层保护、提高采收率的目的。     

纵向泵浦Cr∶ Nd∶GSGG激光棒的热透镜效应研究

对纵向泵浦Cr∶Nd∶GSGG激光棒的热透镜效应进行了详细的理论分析。对温度分布的函数表达式 ,进行了讨论 ;分析了热引起的应力 ,得到了激光棒破裂的临界功率公式 ;最后对光学畸变进行了分析与讨论 ,推导了光程差计算公式     

Nd3+:Y0.5Gd0.5VO4晶体生长和基本特性

Nd^3 :Y0.5Gd0.5VO4晶体作为一种新的激光材料，可以用中频感应加热提拉法生长。X射线粉末衍射分析表明它的结构与Nd^3 :YVO4晶体结构相同，它的晶格常数介于YVO4和NdVO4晶格常数之间。用ICP光谱法测定晶体中Nd^3 含量为0．8at％，分凝系数为0．8，与Nd^3 :GdVO4晶体中Nd^3 的分凝系数0．78相当；用称重法测定其密度为5．00g／cm^3；用稳态纵向热流法测出其室温热导率为12．5W／mK。实验表明Nd^3 :Y0.5Gd0.5VO4晶体有希望作为高功率ID泵浦激光晶体材料。     

从稳态到动态的空气调节

分析传统空调所提供的稳态参数微气候环境不一定能达到人的舒适和健康的要求,提出符合人本身生理习惯的空调送风方式应该是动态空气调节.认为个人可调节和适宜的环境渐变能同时保证舒适和健康两方面需要.     

水溶液全循环法尿素装置中压分解"三种工艺"的比较

以生产数据结合理论计算的方法系统地比较、分析了水溶液全循环法尿素装置中中压分解“三种工艺”的热能利用、甲铵分解率、总氨蒸出率、水平衡量、一分加热器生产能力等方面的情况，提出应用和配置预分离-预蒸馏工艺的方法，评论该工艺在水溶液全循环法中的地位和作用。     

Phosphorus‐containing polyaryloxydiphenylsilanes with high flame retardance arising from a phosphorus–silicon synergistic effect

Polyaryloxydiphenylsilanes were prepared from phosphorus‐containing diols and diphenydichlorolsilane through solution polymerization. With a stoichiometric imbalance in feed monomers, the resulting polymers exhibited moderate melting points and good processing properties. The polymers prepared showed initial decomposition temperatures above 340 °C, excellent thermal stability, high char yields at 850 °C and very high limited oxygen index values of 56–59. The polymers' char yields and their (P + Si) contents showed linear relationships. © 2003 Society of Chemical Industry     

Thermodynamic and Transport Properties of Liquid HFC-227ea

The thermal conductivity and heat capacity of liquid 1,1,1,2,3,3,3-hepta-fluoropropane (HFC-227ea) have been studied by a high-frequency thermal-wave method over the temperature range of 294 to 345 K at pressures up to 2.8 MPa. The purity of the samples used throughout the measurements is 99.99 mol%. The experimental uncertainties of the thermal conductivity and heat capacity measurements were estimated to be within ±1.5 and ±2%, respectively. The thermal conductivity of HFC-227ea in the liquid phase decreases as temperature increases, while the pressure has an opposite effect.     

CFH-Ⅱ型翻车机传动齿轮轴承座的座脚螺栓联接失效分析与改进

分析了CFH-Ⅱ型翻车机传动齿轮轴承座的座脚螺栓组联接失效(松动)的原因，得出控制和保证合适的螺栓组联接预紧力是防止螺栓联接失效(松动)的关键；依据现场条件，对座脚螺栓进行了设计改进；提出了一种适合现场使用的螺栓预热伸长的装配方法，经实践验证此法是简单可靠的装配方法。     

Enhanced thermal stability of a sputtered titanium-nitride film as a diffusion barrier for capacitor-bottom electrodes

The effect of a thin RuO_x layer formed on the Ru/TiN/doped poly-Si/Si stack structure was compared with that on the RuO_x/TiN/doped poly-Si/Si stack structure over the post-deposition annealing temperature ranges of 450–600°C. The Ru/TiN/poly-Si/Si contact system exhibited linear behavior at forward bias with a small increase in the total resistance up to 600°C. The RuO_x/TiN/poly-Si/Si contact system exhibited nonlinear characteristics under forward bias at 450°C, which is attributed to no formation of a thin RuO_x layer at the RuO_x surface and porous-amorphous microstructure. In the former case, the addition of oxygen at the surface layer of the Ru film by pre-annealing leads to the formation of a thin RuO_x layer and chemically strong Ru-O bonds. This results from the retardation of oxygen diffusion caused by the discontinuity of diffusion paths. In particular, the RuO_x layer in a nonstoichiometric state is changed to the RuO₂-crystalline phase in a stoichiometric state after post-deposition annealing; this phase can act as an oxygen-capture layer. Therefore, it appears that the electrical properties of the Ru/TiN/poly-Si/Si contact system are better than those of the RuO_x/TiN/poly-Si/Si contact system.     

激光抛光技术的发展与展望

介绍激光抛光技术的发展历史,阐明激光抛光的应用现状及未来的发展前景,论述了激光抛光的工艺特点和作用机理,将激光抛光技术与其它抛光技术进行了全面的对比,指出激光抛光的优势及其存在的问题。