Open‐cycle OTEC systems with freshwater product: Effects of noncondensable gases on performance of condenser

An open‐cycle ocean thermal energy conversion (OC‐OTEC) system is one of the energy conversion methods used to generate electricity from ocean thermal energy. For the OC‐OTEC system, steam evaporated from the surface seawater due to flash evaporation drives the turbine. At that time, dissolved gas such as air is introduced into the low‐pressure system (OC‐OTEC system) as the noncondensable gas, which degrades the performance of condensation heat transfer. In this paper, a small‐scale OC‐OTEC experimental unit experimentally investigates the effect of noncondensable gas on the heat transfer performance in a condenser. The experimental results are discussed in comparison with theoretical estimation by the Sparrow–in method. It is shown that the condensation is occupied by heat and mass transfer near a condensation surface and that the condensation efficiency is affected by exhaust quantity of noncondensable gas at a relatively high concentration ratio of condensable gas. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 154(1): 29–35, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20179     

用离子束混合及快速热处理方法形成钽的硅化物

本文描述用离子束透过钽金属膜进行混合和快速热处理方法来形成钽的硅化物.用溅射方法在P型硅衬底上淀积一层金属钽,然后用砷离子束透过钽金属模进行混合,采用快速热处理后形成了平整的硅化钽薄层.使用厚度为500埃的钽金属膜,得到钽的硅化物薄层电阻为5.5Ω/□.研究了砷离子能量、剂量及钽膜厚度对钽的硅化物薄层电阻的影响.用透射电镜和台阶仪对所形成的硅化钽进行了分析和厚度测量.     

Application of SiC-Si functionally gradient material to thermoelectric energy conversion device

Because of its high–temperature chemical stability, SiC ceramic is a promising material for high-temperature device applications such as thermoelectric energy converters. However, the electrical conductivity of SiC ceramic is too low for it to be used as a thermoelectric energy converter at the cold junction. Therefore, we propose a SiC-Si functionally gradient material (FGM) in order to improve the electrical conductivity of the SiC ceramic at the cold junction. An SiC rod was fired in a temperature gradient furnace. One end of the SiC rod was maintained at 2473 K and the other end was maintained at 1973 K for 30 min. After firing, the porous SiC edge fired at 1973 K was dipped into molten Si in order to infiltrate molten Si into the porous SiC. The microstructure of the FGM is classified into three regions: the SiC-Si composite material; the porous SiC ceramic; and the densified SiC ceramic. The electrical conductivity, the Seebeck coefficient and the thermal conductivity for each region of SiC-Si FGM was measured at 300 K; a figure of merit was calculated. The figure of merit of the SiC-Si FGM at the cold junction, at room temperature, was 10⁸ times higher than that of a nongradient SiC ceramic.     

《燃气红外线辐射供暖系统设计选用及施工安装》国家标准图集介绍

介绍了该国家标准图集的主要内容：设计说明、典型设计、工程实例、系统设备、燃气管道安装、液化石油气气化站、电气控制及温度检测、施工安装说明。     

Effect of water inlet velocity on thermal stratification in a mantled hot water storage tank

Thermal stratification in a mantled hot water storage tank is analysed numerically for different water inlet velocities. The aim is to obtain higher thermal stratification and supply hot water for usage as long as possible. Twelve different water inlet velocities to the hot water storage tank are considered. The numerical method is validated by comparing its results against experimental and numerical results from the literature. It turned out that the results obtained from the numerical analysis have shown very good agreements with the results from previous works. As a result, the water temperature in the tank increases with the increase of the water inlet velocities to the mantle but this increment is not proportional. After a period of operation of 7.2 h, which corresponds to the average sunshine duration in Turkey, temperature increments of 6.5 and 35 K have been estimated for the hot water inlet velocities of 0.01 and 0.3 m s^?1, respectively, at a radial distance of 0.1 m and a height of 1 m inside the storage tank. Copyright © 2005 John Wiley & Sons, Ltd.     

The thermal ignition of lignocellulosics in infinite slab and cubic geometries

Wood shaving samples were heated in both cubic baskets and in a previously described system realising the conditions of the ‘infinite slab’ in thermal ignition. Results from the two sets of experiment were found to be totally consistent with each other.     

锆钡镧铝氟化物玻璃的分相研究

本文综述了氟化物玻璃中的分相研究。在前人研究基础上应用透射电镜，X射线能谱，电子能量损失谱及X射线衍射，差热分析等研究了锆钡镧铝氟化物玻璃中的液-液分相，发现此种现象普遍存在于该类玻璃之中。对玻璃成分与分相形貌及微观结构之间的关系、对析出晶相种类及分相与析晶的相互影响进行了研究。提出欲降低氟化物玻璃的光损耗，分相与析晶一样是不容忽视的因素。     

Synthesis and characterization of novel diimide–dinaphthols and resulting poly(urethane–imide)s

Novel diols containing imide groups were prepared via condensation of aromatic dianhydrides with 5‐amino‐1‐naphthol. The diimide–dinaphthols prepared were characterized by conventional methods and used to synthesize new poly(urethane–imide)s (PUIs). All the polymers were characterized and their physical properties, such as solubility, solution viscosity, thermal stability, and thermal behaviour were studied. The polymers obtained showed more thermal stability than typical polyurethanes because of the presence of the imide groups. Copyright © 2003 Society of Chemical Industry     

列车客车用低温发热电缆地面辐射供暖系统的实验研究

对不同地板结构和不同导线间距下发热电缆地面辐射供暖系统的热工性能进行了测试分析，考察了系统的稳定性和可靠性，给出了综合比较结果，分析了影响发热电缆地面辐射供暖系统热工性能的主要因素及其影响规律。     

Characterization of resol resins modified by the addition of PVC plastisols

Plastisols, which are a blend of poly(vinyl chloride) resin and a plasticizer (DEHP), were used as a toughening agent of a resol resin in order to improve the mechanical properties. It was not possible to formulate resol blends by adding more than 10 % of plastisol owing to a lack of apparent homogeneity in the systems, which also showed many air bubbles. The relationship between dynamic mechanical, mechanical and thermal properties and the amount of plastisol added was studied. It was determined from the infrared spectroscopy and dynamic mechanical results that the resol–plastisol blends seem to be formed by a reaction between the phenol and PVC giving a higher crosslinked structure. An improvement in the thermal resistance of the blends at lower temperatures was observed with an increase in the percentage of plastisol. Flexural analysis showed the elastic behaviour of the systems. However, it was not possible to observe the effect of the plasticizer (DEHP) owing to the low quantity of plastisol that was added to the resol. Copyright © 2004 Society of Chemical Industry