大港渣油掺兑催化油浆氧化沥青的研究

重油催化裂化外甩油浆中富含芳烃，可望在国产原油生产优质道路沥青上发挥作用。对大港环烷基渣油中掺兑一定比例的油浆后氧化改善道路沥青性质的可能性进行了研究，结果表明：渣油掺兑油浆氧化，不仅可以有效改善沥青延度，同时也为油浆的合理利用开辟了一条新途径。     

Experimental and analytical study on the spray characteristics of dimethyl ether (DME) and diesel fuels within a common-rail injection system in a diesel engine

This paper investigates the effect of injection parameters on the characteristics of dimethyl ether (DME) as an alternative fuel in a diesel engine with experimental and analytical models based on empirical equations. In order to study macroscopic and microscopic characteristics of DME fuel, this work focuses on the atomization characteristics of DME and compares experimental and predicted results for spray development obtained by empirical models for diesel and DME fuel. Detailed comparisons of spray tip penetration from three different empirical correlations and from visualization experiments of diesel and DME fuels were conducted under various fuel injection conditions. In comparison with the results of different empirical equations for measured spray tip penetration, the experimental results of this study provide good agreement with the calculation results based on empirical equations, except during the earliest stage of the injected spray sequence. The results of atomization characteristics indicate that DME showed better spray characteristics than conventional diesel fuel. Also, the fuel injection delay and maximum injection rate of DME fuel are shorter and lower than those of diesel fuel at the same injection conditions, respectively.     

Stretchable Gold Tracks on Flat Polydimethylsiloxane (PDMS) Rubber Substrate

A process to fabricate stretchable gold tracks on silicone rubber substrates is studied by XPS, static water contact angle measurement, AFM, and SEM. The process involves several steps: removing uncured oligomers by hexane Soxhlet extraction; pre-stretching the substrate; activating the strained silicone surface by an oxygen plasma treatment; coating the strained substrate with 5 nm titanium and 80 nm gold layers; and finally releasing the sample. The plasma treatment creates a thin brittle silica-like layer that temporarily increases the substrate's surface energy. Indeed, the plasma treatment is followed by a hydrophobic recovery. As a consequence, the delay between plasma treatment and metal deposition has to be reduced as much as possible. The silica-like layer can be nicely observed after release. The entire process allows us to obtain stretchable metallized samples that remain conductive even after an excessive deformation leading to electrical failure.     

SFG and DFG investigation of Au(111), Au(210), polycrystalline Au,Au–Cu and Au–Ag–Cu electrodes in contact with aqueous solutions containing KCN and 4-cyanopyridine

We report on potential-dependent in situ SFG and DFG spectroscopy carried out at Au(111), Au(210), polycrystalline Au, Au–Cu and Au–Ag–Cu electrodes in contact with aqueous solutions containing CN⁻ and 4-cyanopyridine (4CP). Spectroelectrochemical work was complemented by cyclic voltammetry. The chief stress has been placed on systematising and quantifying the interaction between 4CP and CN⁻ and the attending effects on the vibrational and electronic structures of the interface. The voltammetric behaviour of the investigated electrodes, modified by the addition of 4CP to the CN⁻ electrolyte, denote changes in the CN⁻ adsorption characteristics and effects of the adsorbed CN⁻ layer on the electrodic reactivity of 4CP. The differences among the investigated electrodes can be explained in terms of their respective degrees of atomic packing or with alloying effects on the stability of adsorbed CN⁻. The potential-dependent spectra have been analysed quantitatively with a model for the second order non linear susceptibility accounting for vibrational and electronic effects. The spectral changes induced by addition of 4CP denote interaction of the aromatic with the electrode through the CN⁻ monolayer. The non-resonant contribution yields information on the effects of 4CP on the fine structure of the bound electron density of states.     

A positive‐working photosensitive polyimide based on thermal cross‐linking and acidolytic cleavage

A novel positive‐working photosensitive polyimide (PSPI) based on a poly(hydroxyimide) (PHI), a crosslinking agent having vinyl ether groups, and a photoacid generator (PAG) was prepared. The PHI as a base resin of the three‐component PSPI was synthesized from 4,4′‐oxydiphthalic anhydride and 2,2′‐bis(3‐amino‐4‐hydroxyphenyl)hexafluoropropane through ring‐opening polymerization and subsequent thermal cyclization. 2,2′‐bis(4‐(2‐(vinyloxy)ethoxy)phenyl)propane (BPA‐DEVE) was used as a vinylether compound and diphenyliodonium 5‐hydroxynaphthalene‐1‐sulfonate was used as a PAG. The phenolic hydroxyl groups of the PHI and the vinyl ether groups of BPA‐DEVE are thermally crosslinked with acetal structures during prebake step, and the crosslinked PHI becomes completely insoluble in an aqueous basic solution. Upon exposure to UV light (365 nm) and subsequent postexposure bake (PEB), a strong acid generated from the PAG cleaves the crosslinked structures, and the exposed area is effectively solubilized in the alkaline developer. The dissolution behavior of the PSPI containing each 11.5 wt % of BPA‐DEVE and of the PAG was studied after UV exposure (365 nm) and PEB. It was found that the difference in dissolution rates between exposed and unexposed areas was enough to get high resolution. A fine positive pattern with a resolution of 5 μm in a 3.7‐μm‐thick film was obtained from the three‐component PSPI. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Organic‐acid‐catalyzed sol–gel route for preparing poly(methyl methacrylate)–silica hybrid materials

In this study, a series of organic–inorganic hybrid sol–gel materials consisting of a poly(methyl methacrylate) (PMMA) matrix and dispersed silica (SiO₂) particles were successfully prepared through an organic‐acid‐catalyzed sol–gel route with N‐methyl‐2‐pyrrolidone as the mixing solvent. The as‐synthesized PMMA–SiO₂ nanocomposites were subsequently characterized with Fourier transform infrared spectroscopy and transmission electron microscopy. The solid phase of organic camphor sulfonic acid was employed to catalyze the hydrolysis and condensation (i.e., sol–gel reactions) of tetraethyl orthosilicate in the PMMA matrix. The formation of the hybrid membranes was beneficial for the physical properties at low SiO₂ loadings, especially for enhanced mechanical strength and gas barrier properties, in comparison with the neat PMMA. The effects of material composition on the thermal stability, thermal conductivity, mechanical strength, molecular permeability, optical clarity, and surface morphology of the as‐prepared hybrid PMMA–SiO₂ nanocomposites in the form of membranes were investigated with thermogravimetric analysis, differential scanning calorimetry, dynamic mechanical analysis, gas permeability analysis, ultraviolet–visible transmission spectroscopy, and atomic force microscopy, respectively. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

A novel direct aerodynamically assisted threading methodology for generating biologically viable microthreads encapsulating living primary cells

In a recent discovery, coaxial electrospinning was explored to encapsulate living organisms within a continuous bio‐polymeric microthread from which active biological scaffolds were fabricated (Townsend‐Nicholson and Jayasinghe, Biomacromolecules 2006, 7, 3364). The cells were demonstrated to have gone through all expected cellular activity without their viability being compromised. These biologically active threads and scaffolds have direct and tremendous applicability from regenerative to therapeutic medicine. Currently these post‐processed cells as composite threads and scaffolds are being investigated in‐depth at a cellular level to establish if the processing methodology has any affect on the cellular make‐up. We now demonstrate a competing non‐electric field driven approach for fabricating composite threads and scaffolds influenced only by a differential pressure. We refer to this novel composite thread to scaffold fabrication methodology as coaxial aerodynamically assisted bio‐threading (CAABT). Our investigations firstly, demonstrate that this technique can process handle living organisms without biologically perturbing them in anyway. Secondly the process is elucidated as possessing the ability to form composite active threads from which biologically viable scaffolds are formed. Finally our study employs florescent activated cell sorting (FACScan), a method by which the cellular dynamics and viability are quantified on control and threaded cellular samples at two prescribed time points. In parallel with FACScan, optical comparison of cellular morphology at three time points within a period of three weeks is carried out to photographically observe any changes in the post‐processed cellular phenotype. Our developmental investigations into this novel aerodynamically assisted threading methodology has unearthed a unique biomicrofabrication approach, which joins cell electrospinning in the cell threading to scaffold fabrication endeavor. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Motor oil classification by base stock and viscosity based on near infrared (NIR) spectroscopy data

In this paper we have tried to build effective model for classification of motor oils by base stock and viscosity class. Three (3) sets of near infrared (NIR) spectra (1125, 1010, and 1050 spectra) were used for classification of motor oils into 3 or 4 classes according to their base stock (synthetic, semi-synthetic, and mineral), kinematic viscosity at low temperature (SAE 0W, 5W, 10W, and 15W) and kinematic viscosity at high temperature (SAE 20, 30, 40, and 50). The abilities of three (3) different classification methods: regularized discriminant analysis (RDA), soft independent modelling of class analogy (SIMCA), and multilayer perceptron (MLP) - were also compared. In all cases NIR spectroscopy was found to be quite effective for motor oil classification. MLP classification technique was found to be the most effective one.     

Effect of the graft yield of maleic anhydride on the rheological behaviors,mechanical properties,thermal properties,and free volumes of maleic anhydride grafted high‐density polyethylene

The rheological behavior, thermal properties, and molecular mobility of a series of maleic anhydride (MA) grafted high‐density polyethylenes were characterized and evaluated. The rheological behavior was studied with a Haake minilaboratory. The viscosity of the samples in their melt state decreased with an increase in the graft yield, and this could be attributed to the higher molecular mobility for samples with a higher degree of grafting. The thermal properties were investigated with dynamic mechanical analysis and differential scanning calorimetry. Positron annihilation lifetime measurements were used to study the effect of the degree of grafting on the chemical environment and the atomic‐scale free‐volume properties. It was found that the grafted MA group played a significant chemical inhibition role in positronium formation when the graft yield was low. The results also indicated that the higher the degree of grafting was, the broader the free‐volume distribution was. The relationship between the microstructure and rheological behavior is discussed. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Grafting of maleic anhydride onto polyethylene through a green chemistry approach

The grafting of a polymer can lead to the improvement and modification of the polymer and thus expand its applications. Grafting methods include solution grafting in organic solvents, melt grafting at high temperatures, and light grafting with radioactive sources. These methods have their advantages and disadvantages. The disadvantages include waste treatment, consumption of energy, and so on. In this study, a hydrothermal process which is called the green approach, was developed to prepare graft copolymers. The effect of various factors on the grafting degree was investigated in detail. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008