用于高频谐振器的PbTiO_3基压电陶瓷

传统的PZT压电陶瓷的相对介电常数较大,一般为1 000以上,用于高频谐振器不易与线路匹配;而PbTiO3基压电陶瓷的相对介电常数较小,一般仅为200左右,对于10 MHz以上频率的谐振器,用PbTiO3基压电陶瓷作为压电振子是最佳的选择。本文主要研究用于高频谐振器的MnO2和Nd2O3改性PbTiO3基压电陶瓷的性质。PbTiO3基压电陶瓷的性质的改善是与此种陶瓷的制备工艺,显微结构和电导机制紧密相关的。     

Microstructure of Feta Cheese Made Using Different Cultures as Determined by Confocal Scanning Laser Microscopy

ABSTRACT: The objective of this work was to observe the microstructure of feta cheese using confocal scanning laser microscopy. Low fat cheese and cheese containing capsule-producing cultures were made. The protein network was observed using the reflectance mode of the confocal microscope. Fat was stained by Nile red dye diluted with whey. More even distribution of fat with a larger number of smaller globules was observed in cheese made with noncapsule-forming culture compared to that made with the capsule-forming culture. Nonfat cheese had compact structure when made with noncapsule-forming culture which contrasted with the open structure observed in cheese made with the capsule-forming culture     

利用信息融合方法的三维特征提取

本文提出了一种基于信息融合的物体三维特征的提取方法，该方法利用两幅互相配准的三维测距图像和灰度图像，来提取多面体的三维特征。首先，通过分析灰度图像中的灰度变化及测距图像中的测距值变化，分别求取各自图像中物体的特征点及特征边；然后，利用两配准图像之间的对应关系，求得所有特征点、面与多边形在三维测距图像中的三维表示；接着，通过分析三维测距图像中所测得的各候选平面上特定点与边处的曲率及法向，验证候选平面     

Processing and microstructure of non-oxide ceramic fibres

Research and development efforts on high-temperature, oxidation-resistant fibres have increased over the past decade due to the demand for light-weight, stiff and strong composite materials in aerospace applications. Varieties of ‘high-performance’, continuous, non-oxide fibres with low-density, high tensile strength and tensile modulus have been developed either from organic precursors or via chemical vapour deposition for fabrication of ceramic matrix composites. Fibres derived from polymer precursors (e.g. Nicalon, Tyranno, HPZ) are small in diameter (compared to CVD monofilaments) and are ideally suited for ceramic composites. Processing, microstructural stability and mechanical properties of these newly developed SiC and Si₃N₄ base fibres are briefly reviewed in this paper.     

Microstructure-Property Correlation in AI_4C_3 Dispersion Strengthened Al Composite

The microstructure and tensile properties of Al_4C_3 dispersion strengthened Al composite fabricatedby reaction milling technique were investigated.It is indicated that the rod-like Al_4C_3 dispersoidshaving a diameter of 0.02-0.03 μm and a length of 0.1-0.3μm are formed by reaction of C with Al,and uniformly distributed in the Al matrix.The interface between Al_4C_3 and Al is clean and theinterfacial bonding is good.The matrix consists of the subgrains which have the size of 0.3-0.4μm,and most of the Al_4C_3 dispersoids are distributed on the subgrain boundaries.The 11 vol.-%Al_4C_3/Al composite exhibits an UTS (ultimate tensile strength) of 400 MPa and anelongation-to-failure of 8.0%.     

LD钢超塑性压缩变形参数与金相组织

通过对ＬＤ（７Ｃｒ７Ｍｏ３Ｖ２Ｓｉ）模具钢起塑性压缩变形后的金相组织观察研究，分析了变形参数、原始组织对变形后金相组织的影响。     

濮城油田东西区沙二下顶面微构造特征与剩余油分布

濮城油田沙二下是一个被断层复杂化了的断块型油气藏，通过对储层的精细描述表明，各砂岩组顶面微构造发育，其成因有2种，与构造作用有关的微构造及与构造作用无关的微构造，前者规模较大，后者规模通常较小，根据微构造的起伏变化和形态，可分为3类：正向微构造，负向微构造，斜面微构造，正向微构造是油气富集与控制剩余油分布的重要微构造。     

半固态ZnAl 27合金及其二次加热组织

研究了半固态ZnAl27合金及其二次加热组织。结果表明，半固态ZnAl27合金基本无宏观偏析，其组织为细小均匀的近球形非枝晶，综合力学性能远远高于常规铸造合金；二次加热后，α相进一步球化，边缘变得光滑圆整，可以满足半固态触变成形的需要。     

激光熔覆Ni基SiC合金涂层组织与性能的研究

利用5kWCO2连续波激光器在16Mn钢基材表面对含20%(体积比)SiC陶瓷粉末的镍基自熔性合金粉末进行激光熔覆得到Ni基SiC合金涂层(NiSiC)。研究了合金涂层的组织形貌及相结构,并用单纯的镍基合金涂层(Ni60)进行了显微硬度及滑动磨损性能的对比试验。结果表明,NiSiC合金涂层由γ枝晶及其间的共晶组织组成,主要组成相为γ-Ni,γ-(Ni,Fe)固溶体和(Cr,Fe)7C3,Cr23C6及(Cr,Si)3Ni3Si等化合物。添加SiC的镍基合金涂层NiSiC比单纯的镍基合金涂层Ni60具有较高的硬度和耐磨性。     

内循环好氧三相流化床处理造纸中段废水

本实验采用内循环好氧三相流化床处造纸中段废水，经过一段时间的驯化，获得了稳定的出水。CDO去除经保持在65％以上，系统对进水污染负荷的变化具有较大的承受能力。出水Cl^-的浓度有所增加，说明驯化后的微生物可能对有抽氯化物具有一定的降解作用。水气比在1／120至1／140之间可获得最好的COD去除效果。后进行絮凝处理后，出水COD降为60－80mg/L,BODo 50-60/L，色度为100－150CU，挥发性酚的质量浓度小于0．0265mg／L。