基于Nios Ⅱ的CCD采集系统的设计

设计了一种在NiosⅡ处理器上的CCD数据采集系统。电荷耦合器件（Charge—Coupled Device,CCD）采集到的信号经过前端的差分运放处理后再进行A／D转换,转换后的数据存储于外部SDRAM中,被读取后显示在LCD上。本文重点介绍了各器件的电路设计和驱动程序的编写。实践表明,该设计成本低,实时性较高。     

基于IEC61131-3标准的PLC编辑模块设计与实现

基于IEC61131-3标准设计一个可编程逻辑控制器（PLC）编辑模块,并给出了主要数据结构和算法的设计。通过测试表明用户界面友好,操作简单,对后续开发具指导意义。     

一种基于UML状态图的规约变异测试方法

规约变异测试从软件功能的角度,对规约进行分析,从而揭示规约中存在的问题。本文提出一种基于UML状态图的变异测试方法,针对每种变异算子,分析其是否会引入冲突,进而有效避免不合理的变异操作;分析了每种变异算子产生等价变异体的条件,能够在生成变异体的同时检测并移除等价变异体,进而减少其对测试过程的影响;给出了杀掉每种变异体所需满足的条件,可在此基础上产生杀掉特定变异体所需的测试用例,从而提高测试用例集的质量。在此基础上,根据变异算子的实际功能,整合了功能相同的算子,减少了变异算子的数量,从而进一步降低了变异测试的开销。实验结果表明,本方法能够较好地提高测试用例的质量,进而提升测试的效率。     

A faster divide-and-conquer algorithm for constructing delaunay triangulations

An easily implemented modification to the divide-and-conquer algorithm for computing the Delaunay triangulation ofn sites in the plane is presented. The change reduces its (n logn) expected running time toO(n log logn) for a large class of distributions that includes the uniform distribution in the unit square. Experimental evidence presented demonstrates that the modified algorithm performs very well forn2¹⁶, the range of the experiments. It is conjectured that the average number of edges it creates—a good measure of its efficiency—is no more than twice optimal forn less than seven trillion. The improvement is shown to extend to the computation of the Delaunay triangulation in theL _p metric for 1<p.This research was supported by National Science Foundation Grants DCR-8352081 and DCR-8416190.     

65Mn钢CCT曲线及圆锯片淬火工艺

用全自动相变测定仪测定了圆锯片常用６５Ｍｎ钢的连续冷却转为曲线，研究了不同连续冷却速度下得到的组织，为合理制订圆锯片的淬火工艺提供了依据，得到了最佳淬火工艺曲线。     

Simulation of polycrystalline aluminum tensile test with crystal plasticity finite element method

The crystal plasticity was implemented in the finite element method（FEM） software ABAQUS through the user subroutine UMAT. By means of discretizing the space at the grain level with the Voronoi diagram method, a polycrystal model was built and used in the FEM analysis. The initial orientation of each grain was generated based on the orientation distribution function（ODF）. The developed model was successfully applied in simulation of polycrystalline aluminium samples deformed by the tensile tests. The theoretical strain--stress relation was in good agreement with the experimental result. The simulation results show that the grain size has significant effect on the deformation behavior. The initial plastic deformation usually occurs at grain boundaries, and multiple slip often results in an enhanced local hardening at grain boundaries.     

电缆化配电系统高频谐振频移方法

为解决电缆化配电网高频谐振问题,提出了一种基于配电网阻抗重构的高频谐振频移方法。首先,分析了电缆化配电网高次谐波源与高频谐振的产生机理。其次,给出了电缆化配电网阻抗重构的高频谐振频移方法,并比较不同无源阻抗重构后的频移及谐振峰抑制效果。然后,结合实际工程案例,利用系统函数绘出伯德图与根轨迹评价该方法对高频谐振治理效果以及系统稳定性的影响,验证了基于电缆化配电网阻抗重构的高频谐振频移方法的有效性,最后研究了无源阻抗参数变化对配电网高频谐振的影响。     

纱线烘干系统的PLC改造与应用

介绍了烘房烘干的工艺过程，及应用PLC在该系统中进行电气控制系统改造，使系统烘干质量高，工作可靠，设置、操作简单，提高了生产效率。     

Investigation of the titanium–indium system

The phase diagram of the Ti–In system was determined using DTA, XRD and EDX analyses. The existence of the phases Ti₂In₅ [Mn₂Hg₅ type structure, space group P4/mbm, a=0.99995(3), c=0.29960(2) nm] and Ti₃In [Ni₃Sn type structure, space group P6₃/mmc, a=0.5978(1), c=0.4812(1) nm] was confirmed. The phase previously labeled Ti₃In₂ was found to exist in a narrow homogeneity region near Ti₅₆In₄₄. Rietveld refinement of the XRD powder pattern yielded solutions compatible with a Cu₃Au-type or a BiIn-type crystal structure, but not with a CuAu-type crystal structure. Furthermore, at 38.5 at.% In, a new phase was observed having a γ-brass related crystal structure [Ti₈In₅, space group , a=0.99578(6) nm]. The intermetallic phases were formed by a cascade of peritectic reactions ending in a eutectic at >99 at.% indium between Ti₂In₅ and (In) at 0.4 K below the melting temperature of pure indium.