Discrete Modeling and Suggested Measurement of Heat Transfer in Gas-Solids Flows

This article presents a two-dimensional transient model for gas-solids flow and heat transfer through pipes using the coupled Computational Fluid Dynamics and Discrete Element Method approach. Numerical simulations have been conducted to examine the modification of fluid thermal structure due to the presence of particles in a pneumatic transport pipeline. Modeled results have demonstrated the key role of transversal motion of rebounding particles in the pipe cross section in altering fluid temperature. Further implementation of this modeling technique in air-drying processes is discussed and possible experimental methods for the measurement of in situ particle and fluid motion and temperature profile are cited.     

冷41-平14"L"型水平井轨迹优化与控制技术

冷41-平14井受地面条件的限制,靶前位移小,为保证中间套管和完井管柱的顺利下入,剖面设计为“反向造斜-稳斜-降斜-正向造斜-水平段”的“L”型。简要介绍了冷41-平14“L”型水平井的设计概况,详细介绍了该井井眼轨道优化设计原则和设计结果,以及实钻井眼轨迹连续控制技术。该井精确命中A、B靶,两靶处的井斜角、方位角和垂深等达到了设计要求,在A靶实现了软着陆。该井井眼轨道优化设计和井眼轨迹控制技术为类似水平井的井眼轨道设计和轨迹控制提供了有益的借鉴。     

基于S-CDMA的HFC上行信道接入协议性能仿真分析

讨论了基于S－CDMA的HFC网上行信道的高效接入协议－SAMA，提出了双信道接入机制的工作原理，并对系统性能进行了分析与计算机仿真，得到一些有意义的结论。     

Investigation of Ni/4H-SiC diodes as radiation detectors with low doped n-type 4H-SiC epilayers

The development of SiC minimum ionising particle (MIP) detectors imposes severe constrains in the electronic quality and the thickness of the material due to the relatively high value of the energy required to produce an electron–hole pair in this material by MIP against the value for Si. In this work, particle detectors were made using semiconductor epitaxial undoped n-type 4H-SiC as the detection medium. The thickness of the epilayer is on the order of 40 μm and the detectors are realised by the formation of a nickel silicide on the silicon surface of the epitaxial layer (Schottky contact) and of the ohmic contact on the back side of 4H-SiC substrate. The low doping concentration (6×10¹³ cm⁻³) of the epilayer allows the detector to be totally depleted at relatively low reverse voltages (100 V). We present experimental data on the charge collection properties by using 5.486 MeV -particles impinging on the Schottky contact. A 100% charge collection efficiency (CCE) is demonstrated for reverse voltages higher than the one needed to have a depletion region equal to the -particle extrapolated range in SiC. The diffusion contribution of the minority change carriers to CCE is pointed out. By comparing measured CCE values to the outcomes of drift–diffusion simulation, values are inferred for the hole lifetime within the neutral region of the charge carrier generation layer.     

Humans: the missing link in manufacturing simulation?

Computer based discrete event simulation (DES) is one of the most commonly used aids for the design of automotive manufacturing systems. However, DES tools represent machines in extensive detail, while only representing workers as simple resources. This presents a problem when modelling systems with a highly manual work content, such as an assembly line. This paper describes research at Cranfield University, in collaboration with the Ford Motor Company, founded on the assumption that human variation is the cause of a large percentage of the disparity between simulation predictions and real world performance. The research aims to improve the accuracy and reliability of simulation prediction by including models of human factors.     

Influence of a Jump in the Power of Laser Radiation on Its Measurement

Simulation and investigation of the effect of an isolated jump on realization of the unit of power of laser radiation and dissemination of the size of the unit are considered. Results are obtained by means of a newly developed algorithm that characterizes the behavior of the mean value of a signal and the standard deviation of a system as functions of the parameters of a jump in the power of laser radiation and the length and amplitude of the jump. If information concerning the time when a jump occurs is available, the proposed algorithm makes it possible to take into account how a jump affects the ultimate result of a measurement.     

Numerical simulation of slider dynamics during slider–disk contact

In this paper, the dynamic behavior of pico slider in contact with the disk was calculated. The analysis model consists of a simplified suspension model, an air bearing model, and a slider–disk contact model. The contact model consists of two elements. One is surface roughness model measured by Atomic Force Microscope (AFM) and the other is micro-waviness model. The dynamic behaviors of the tri-pad slider are calculated at several rotation speeds to investigate slider vibration modes during slider–disk contact. The slider oscillation frequency depends on the rotation speed and it saturates about twice as much as eigen frequency of air bearing pitch mode.     

精馏塔静态仿真：Ⅰ.静动态混合数学模型的应用

本文为了克服精馏塔静态仿真不易收敛和初值难以给定等难题，巧妙地利用隐含数值积分方法的特点，将稳态与动态数学模型耦合起来，用以求解高难度的非理想精馏塔静态仿真问题。所得静动态混俣模型大大提高了精馏塔静态仿真的鲁棒性，对于高度非理想精馏塔的仿真尤为有效。通过对某丙烯腈萃取精馏塔的静态仿真，充分证明了这种混合模型化方法的可行性。     

微机模拟处理pH络合滴定法研究——Ⅱ.终点确定方法和最佳实验条件模拟估计程序

本文利用简便的滴定过程模型,确立了微机模拟处理实验数据,方便、准确地求解络合滴定等当点的方法。设计了最佳实验条件模拟估计程序。该法测定Zn~(2+),Pb~(2+),Cu~(2+),Fe~(3+)结果的相对误差Δ<1％。pH=6-7时,测定Ca~(2+)的相对误差为-1.61％;σ<0.001mmol,(N=5)。