纳米加工和纳米电子器件

介绍了电子束曝光技术、EUV光刻技术和X射线光刻技术的进展;对各种纳米电子器件如单电子器件、共振隧穿器件和分子电子器件的研究现状及面临的主要挑战进行了讨论。     

氧化铝熟料单筒冷却机节能技术改造

本对影响氧化铝熟料单筒冷却机冷却效率的因素进行了分析，并提出了相应的节能技术改造措施，取得了明显的节能效益。     

SDS/正戊醇/水体系的液晶研究

在 2 5℃测定了十二烷基硫酸钠 (SDS) /正戊醇 /水三元体系的相平衡 ,确定了液晶区域的边界范围。在液晶区域内选取一系列样品点 ,用差示扫描量热法 (DSC)和2 HNMR与液晶照片对照 ,研究了该体系的液晶结构特点。结果表明 :在恒定温度下 ,该体系存在着两个液晶区域 ,并且随含水量的增加 ,液晶结构发生变化。当组成固定时 ,体系的液晶相结构随温度升高也发生变化     

Aspects of rapid crack propagation in silicon

Fracture experiments with silicon specimens in recent years have shown the need for a new approach to the analysis of rapidly propagating cracks in single crystals. Behaviour and phenomena have been revealed that fracture in these materials is rather different from the fracture of both amorphous and polycrystalline materials. We show that continuum mechanics is insufficient for analyzing crack propagation in single crystals since it is unable to consider atomistic‐scale phenomena. Accordingly, we describe basic phenomena associated with rapid crack propagation in silicon : (i) anisotropic velocity‐dependent R‐curve behaviour, as a key phenomenon dictating atomistic scale behaviour, (ii) crack deflection from one cleavage plane to another as a mesoscopic scale phenomenon in single‐crystal fracture, (iii) the Rayleigh surface wave speed as the limiting crack tip velocity is re‐examined, (vi) the lowest crack velocity in brittle crystals is examined, and finally (v) the interaction between crack path and preferred cleavage planes in single crystals is depicted.     

钻井液振动筛叠层筛网透筛率的研究

从理论上详细论述了钻井液振动筛叠层筛网对固相颗粒分离的影响 ,首次提出用透筛率的概念定量地描述这一影响 ,并进行了实例计算。研究表明 ,当上下层筛网随机叠加时对透筛率的影响有以下几种情况 :(1)当上下层筛网开孔尺寸相除的余数为零 ,任意组合叠层筛网的透筛率分别为某一常数 ;(2 )上层筛网目数一定时 ,下层筛网目数越大 ,则透筛率越小 ;(3)上下层筛网的目数相差越小 ,透筛率越小 ;(4 )任意目数的上下层筛网随机叠加后 ,其透筛率仅在一个小范围内变化 ,因此任一叠层筛网有其固有的透筛率属性。     

Improved direct bonding method of Nd:YVO4 and YVO4 laser crystals

We succeeded in the fabrication of bonded laser crystals composed of a neodymium-doped YVO₄ laser crystal (Nd:YVO₄) and its host crystals YVO₄ by a newly developed dry etching technique using an argon ion beam. The optical distortion caused by the bonded interface of size 5 mm × 6 mm was estimated to be 0.05λ at 633 nm. From the comparison of laser performance pumped by a laser diode, the bonded crystals could increase the laser output power by nearly twice that of the non-bonded crystals with the same degree of polarization of 99.2%. To analyze the mechanism of the enhanced reduction of the thermal load in the bonded crystals, numerical simulations with a finite-element method were also performed.     

Water‐Stable,Magnetic Silica–Cobalt/Cobalt Oxide–Silica Multishell Submicrometer Spheres

A method to produce monodisperse magnetic composite spheres with diameters from less than 100 nm to more than 1 μm in water solution is reported. The spheres consist of a dielectric silica core and a cobalt/cobalt oxide shell which can be protected from further oxidation with an outer shell of silica or, alternatively, they can be covered with the polymer polyvinylpyrrolidone as a stabilizer. The formation of a uniform magnetic shell proceeds with the adsorption of metallic cobalt seeds, produced by the reduction of cobalt chloride with sodium borohydride, on a self‐assembled layer of polyelectrolytes on the silica core. In the second step, an outer silica shell can be formed by the hydrolysis and condensation of (3‐aminopropyl)trimethoxysilane and tetraethoxysilane. The double‐shell composite spheres show excellent sphericity, monodispersity, and a magnetic hysteresis loop at room temperature.     

机械合金化过程中Fe70B30粉末晶粒尺寸和微观应变的研究

用Ｘ射线和电镜研究了Ｆｅ＿（７０）Ｂ＿（３０）粉末经不同时间高能球磨后晶粒尺寸和微观应力的变化。在机械合金化过程中，粉末的Ｘ射线衍射谱的宽度随球磨时间的增加逐渐加宽，这是晶粒细化和内部微观应力共同作用的结果。Ｘ射线衍射结果表明：随着机械合金化的进行，粉末的晶粒尺寸逐渐减小，球磨初期晶粒尺寸下降较快，经１５ｈ球磨，晶粒尺寸为２５ｎｍ，机械合金化进行到一定时间后晶粒尺寸下降缓慢，８０ｈ球磨后晶粒尺寸可达５ｎｍ。在机械合金化过程中球磨所造成的微观应变不大，球磨初期粉末的内应力随球磨时间增加而增加，当粉末粒子尺寸很小时，随球磨的进行粉末中的微观应变显著下降。     

EXPERIMENTAL STUDIES AND NUMERICAL CALCULATION ON TURBULENT BOUNDARY LAYER OF WATER FLOW ALONG CURVED SURFACE

This paper will introduce experimental studies and numerical calculation onturbulent boundary layer of water flow along curved surface in our country in recent years.Onthe basis of the experimental studies,the effects of curvature and roughness on velocitydistribution and pressure distribution and the change of turbulent flow boundary layer onoverflow bucket concave surface is discussed.We proposed the empirical formula of velocity,pressure and the change of turbulent flow boundary layer on outlet bucket concave.According tothe momentum principle,we have deduced the momentum integral equation full water depthboundary layer and using the element as control unit inside the boundary layer on concavesurface of bucket.Combining with continuity equation,we have computed the boundary layerdevelopment on the bucket of a spillway.Compared with the field experimental data,thecalculation results are available.Under polar coordinates,a mathematical model for simulatingtime-averaged flow characteristics in concave surface of bucket is established.The turbulent flowfield on concave surface of bucket is calculated by SIMPLE method and this mathematicalmodel.The flow velocity field,pressure field,distribution of turbulent kinetic energy,distribution of turbulent energy dissipating rate and distribution of shear stress are available.Thecalculation value is consistent with measured test data.