Experimental evaluation of the strength distribution of E-glass fibres at high strain rates

A bimodal Weibull distribution function was applied to analyse the strength distribution of glass fibre bundles under tensile impact. The simulation was performed using a one-dimensional damage constitutive model. The results show that there were two concurrent flaw populations in the fracture process. The regression analysis using the bimodal Weibull distribution function was in good agreement with experiment.     

泡沫铝的动态压缩性能和吸能性研究

通过测量泡沫铝在动态和准静态压缩条件下的应力 -应变曲线 ,研究了泡沫铝的准静态和动态压缩行为以及不同应变条件下的吸能性 ,并对其应变率效应进行了分析。结果表明 ,在高应变速率和准静态压缩下 ,泡沫铝的σ -ε曲线均表现出弹性变形段、平缓段和密实段三阶段特征 ;泡沫铝的压缩性能具有明显的应变速率敏感性 ,随应变速率的提高 ,流动应力上升 ,吸能性升高     

An efficient assumed strain element model with six DOF per node for geometrically non-linear shells

The present paper describes an assumed strain finite element model with six degrees of freedom per node designed for geometrically non-linear shell analysis. An important feature of the present paper is the discussion on the spurious kinematic modes and the assumed strain field in the geometrically non-linear setting. The kinematics of deformation is described by using vector components in contrast to the conventional formulation which requires the use of trigonometric functions of rotational angles. Accordingly, converged solutions can be obtained for load or displacement increments that are much larger than possible with the conventional formulation with rotational angles. In addition, a detailed study of the spurious kinematic modes and the choice of assumed strain field reveals that the same assumed strain field can be used for both geometrically linear and non-linear cases to alleviate element locking while maintaining kinematic stability. It is strongly recommended that the element models, described in the present paper, be used instead of the conventional shell element models that employ rotational angles.     

含损伤软化材料层合板承压时的分叉分析

本文讨论了由纤维和树脂-损伤应变软化材料组成的层合板在面内受压时的压缩分叉。用有限变开理论和半解析有限元法建立了相应的分叉方程,并进行数值模拟。计算结果表明,分叉将在损伤材料的应变软化阶段发生,为剪切带形分叉,损伤材料骨有剪应变集中,而且在纤维和树脂的界面附近有较大的剪应变突变等现象。     

Mechanoluminescent pulse pressure sensors. Processing of output optical signal

The process of mechanoluminescence transformation of a pulse pressure sensor is considered. The process consists in excitation of emission under the action of mechanical loading. An algorithm for use in processing the output optical signal of the sensor that makes it possible to determine an input shock pulse is presented. __________ Translated from Izmeritel’naya Tekhnika, No. 10, pp. 28–31, October, 2007.     

基桩反射波法动测曲线的数值模拟与特征分析

采用美国PDI公司开发的PDI-S软件,对不同缺陷基桩的反射波法低应变动测曲线进行数值模拟,对动测曲线的特征进行归纳与总结,以便在解释反射波法曲线时作为参考与借鉴,提高基桩质量检测的可靠度。     

钛合金的银脆,镉脆敏感性及其控制

利用慢应变速率拉伸技术（ＳＳＲＴ），并结合恒载实验，较全面地研究了Ｔｉ－６Ａｌ－４Ｖ合金的银脆行为、固态与液态镉脆行为，确定了应变速率、接触条件、热处理制度、试样取向、温度等因素对Ｔｉ－６Ａｌ－４Ｖ合金银脆与镉脆敏感性的影响，探讨了Ｎｉ阻挡层对控制Ｔｉ－６Ａｌ－４Ｖ合金和ＴＣ１１合金银脆开裂的作用。     

压阻式压力传感器及其应用电路设计

介绍了压阻式传感器的工作原理以及相关应用电路，并给出了一个应用示例加以说明。     

K0.9Li0.1（Ta0.5Nb0.5）O3晶体压电应变系数的测量

用准静态ｄ＿（３３）测量仪和干涉法相结合。测量了Ｋ＿（０．９）Ｌｉ＿（０．１）（Ｔａ＿（０．５）Ｎｂ＿（０．５）Ｎｂ＿（０．５））Ｏ＿３晶体的压电应变系数。结果为：ｄ＿（３３）＝８６．０，ｄ＿（３３）＝一２９．５，ｄ＿（１５）＝１１２．９×１０￣（－１２）Ｃ／Ｎ．     

关于离散Kirchhoff薄板单元的研究

本文对离散Kirchhoff薄板单元进行了深入的分析。文中将用于建立离散Kirchhoff单元的泛函分为三部分,分别用应变第一不变量、绕Z轴的转动偶和有关的单元边界上的积分来表达,并阐明了各部分的作用。其中单元的收敛性质完全由第一、三部分所决定,而第二部分则控制了单元的计算精度。在此基础上,文中建议了一种提高离散Kirchhoff单元精度的新方法,并由此推导了一个任意四边形离散Kirchhoff单元。计算表明,本文的改进单元与原来的离散Kirchhoff单元及其改进型相比,计算精度有了显著提高。