液态金属实验回路(LMEL)的总体设计和运行

液态金属实验回路（ＬＭＥＬ）是国内唯一用于聚变堆磁流体动力学（ＭＨＤ）效应和材料相容性研究的大型实验装置。与国外同类先进的装置相比，回路流程和运行方式均有重大改进，使其更先进、安全并具有多功能。回路运行分为两个阶段：第一阶段以钠－钾低共熔合金（２２Ｎａ７８Ｋ）为工质，研究ＭＨＤ效应，ＬＭＥＬ的最大哈特曼（Ｈａｒｔｍａｎｎ）数Ｍ和相互作用参数Ｎ分别为０．７５×１０４和２．５×１０４；第二阶段以液态锂为工质，研究结构材料与锂的相容性，最高温度和流速分别为５２０℃和１．３８ｍ／ｓ。     

Temperature Dependence of Cobalt Release Rate from Stainless Steel in Neutral Water

In order to evaluate the release source of Co from heated tubes of the feedwater line of BWR, Co release rate measurements were carried out by measuring ⁶⁰Co released from irradiated stainless steel in contact with neutral water at an oxygen concentration of 20 ppb. The temperature- and time-dependences on Co release rate were studied for 670 h release experiments; the rate was found to decrease in proportion to t ^?frac12 (t ^?frac12 (t: exposure time) and to have its maximum value around 240°C. An empirical equation was obtained for the Co release rates in the temperature range of 150~240°C.

R_Co = 1.9 × 10⁶ exp (-14,300/(RT)) t ^?frac12

where R _co Co release rate (mg/(dm²·month)), R: Gas constant (cal/(mol·deg.)), T: Exposure temperature (K) and t: Exposure time (h). Decrease in the Co release rate with temperatures over 250°C, seemed to be ascribed to the formation of a protective oxide layer on the surface of stainless steel.     

添加微细铬铁粉对烧结钢摩擦磨损性能的影响

研究了加入不同含量的微细铬铁粉对烧结钢干摩擦磨损性能的影响,并借助于扫描电镜观察分析其磨损形貌,探讨摩擦磨损机制。研究结果表明:添加微细铬铁粉可改善烧结钢的强度、硬度和摩擦磨损性能,铬的质量分数为1.5%时,耐磨性最佳。磨损造成一定厚度的塑性变形,硬度较高的材料塑性变形层较薄。磨损早期,磨粒磨损是主导机制,磨损后期,由于塑性变形导致亚表层产生裂纹,进而发生的剥层磨损是主导磨损机制。     

二维三氧化钨纳米结构的合成及其在光电探测器中的应用

三氧化钨（WO₃）是制造晶体管和光电探测器的理想材料,虽然在WO₃纳米结构的生长方面已经完成了一些工作,但是制造足够长的理想型纳米线仍然是一个挑战。在众多的合成方法中,作者选择了化学气相沉积（CVD）方法合成WO₃纳米线,并对其在光电传感器中的应用进行了研究。影响WO₃纳米线成品率的主要因素是前体材料温度、基片位置、载气流速和生长持续时间。在合适的生长条件下生长的纳米线长度最长约为100 μm。这些WO₃纳米线可用来制造高性能的光电探测器,WO₃光电探测器具有灵敏度高、响应速度快、模块微型化等优良的器件性能,表明二维WO₃纳米线在光电探测器的制造中具有很大的优势。      

Preparation and structure of fluorinated/non-fluorinated polyacrylate gradient emulsion blend film

The emulsion blend method, which is environmentally friendly and energy saving, was used to prepare a compositional gradient film of fluorinated/non-fluorinated polyacrylate in this paper. The size and glass-transition temperature (T_g) of the emulsion particles were designed to enhance the driving force of their selective congregation and promote the formation of gradient structure. The structures and surface properties of the obtained films were characterized. The results showed that when the fluorinated components have much smaller particle size and higher T_g than those of fluorine-free polyacrylate components, the gradient structures formed in the direction across the film thickness of the films. The concentration of the fluorinated component increased gradually from film-glass interface to film-air interface in the blend film, making the surface free energies of the two sides of the gradient film distinctively different.     

Metal‐containing Polymers via Electropolymerization

Electropolymerization represents a suitable and well‐established approach for the assembly of polymer structures, in particular with regard to the formation of thin, insoluble films. Utilization of monomers that are functionalized with metal complex units allows the combination of structural and functional benefits of polymers and metal moieties. Since a broad range of both electropolymerizable monomers and metal complexes are available, various structures and, thus, applications are possible. Recent developments in the field of synthesis and potential applications of metal‐functionalized polymers obtained via electropolymerization are presented, highlighting the significant advances in this field of research.     

Correlation between structural and optical properties of 30 nm and 60 nm lead sulfide nanowires

PbS nanowires with 30 nm and 60 nm diameter fabricated under the same condition of electrochemical deposition with sulfuric and oxalic anodic alumina membranes (AAM), respectively, have been successfully prepared in order to study their optical properties in relation to their size. Scanning electron microscopy indicates that the 60 nm PbS nanowire arrays have the same shape with the 30 nm. X-ray diffraction result shows that 60 nm PbS nanowires are crystalline and have a highly (200) preferential orientation like 30 nm ones. UV spectrum considers the nanowire size decrease as the absorption peak shifts to the blue. The quantum confinement effects compared between 30 nm and 60 nm PbS nanowire arrays were observed by the measurements of ultraviolet-visible absorption spectroscopy (UV-vis).     

金属材料断裂韧度JIC试验方案研究

鉴于多数断裂韧度JIC试验无法按GB／T2038—1991测出结果，对JIC试验方案进行了分析，探讨了在JIC测试中存在的问题并应用GB／T2038—1991和GB／T2038—1980进行了相应的试验。结果表明，按照GB／T2038—1991标准试验的可行性与材料的有效屈服强度有关；采用GB／T2038—1991标准测出的JIC值一般比旧标准偏大；GB／T2038—1991已经不能适应材料发展的需要，迫切需要修订和完善。     

纳米WO3材料的制备、应用及研究趋势

结合近年来国内外相关文献，综述了纳米WO3材料的研究现状与进展，重点概述了超细WO3粉体和纳米WO3薄膜的各种制备方法及各自优缺点，并介绍了纳米WO3薄膜的稀有金属掺杂研究等；分析了纳米WO3材料的研究意义，介绍了纳米WO3材料在变色及催化等方面的应用。最后分析了纳米WO3材料应用的发展趋势。     

脲醛树脂基高分子材料改性研究

本文简要介绍了脲醛树脂基高分子材料的基本生产工艺流程,探索玻璃纤维、纳米蒙脱土、丁腈橡胶粉以及玉米淀粉种类和用量对脲醛树脂基高分子材料耐电击穿性能的影响。实验结果表明,选用玻璃纤维作为增强剂对脲醛树脂基高分子材料的耐电击穿强度影响最为明显,纳米蒙脱土次之,玉米淀粉的加入对脲醛树脂基高分子材料的耐电击穿强度影响不明显,而丁腈橡胶的加入对脲醛树脂基高分子材料的耐电击穿强度有明显的下降趋势,改性后的脲醛树脂基高分子材料的耐电击穿强度能超过17KV/mm,最佳耐压时间在100s以上。