换热器小浮头螺栓断裂失效分析

针对换热器小浮头螺栓发生断裂的情况进行失效分析，找出原因，提出处理措施及材质选择时应注意的问题。     

甲醇氧化羰化制碳酸二甲酯产物气相色谱分析

以Chromosorb 10 1为固定相 ,气相色谱法分析甲醇氧化羰化制碳酸二甲酯产物中水、甲醇、乙酸甲酯和碳酸二甲酯等组份的含量 ,考察了柱温 ,载气流量对分离度的影响 ,确定了适宜的分析条件 ,并用校正面积归一化法定量。该方法操作简便 ,快速 ,精度高 ,重现性好     

分析型全蒸发器在啤酒挥发性成分测定中的应用

综述了分型全蒸发器技术在啤酒发酵过程中的应用状况，并介绍了分析型全蒸发器模型结构及与之配合使用的连续多分支管。     

广州地铁一号线隧道结构变形监测及成果分析

介绍了广州地铁一号线运营以来的全线隧道结构变形监测 ,分析了隧道结构的安全状况和各种变化规律 ,并对其变形原因进行有益的探讨     

Model validation and model structure determination

This paper gives a tutorial overview of basic approaches for model validation and model structure determination.Work partially supported by the Swedish Research Council for Engineering Sciences under contract 98-654.     

Failure analysis of aluminum cable steel reinforced (ACSR) conductor of the transmission line crossing the Paraná River

The failure of the conductor of the 460 kV overhead transmission line located along the crossing of the Paraná River was investigated. As a result of this failure, a blackout took place in the southern states of Brazil in January of 2002, reaching approximately 67 million inhabitants. Investigation of the external aluminium layer of the ACSR conductor near the fracture showed typical static deformation marks and dynamic fretting wear tangential marks, both associated with the presence of Al₂O₃ debris. Additionally, encrusted silicon particles were observed on the external surface of the strands. The internal Al layer showed elliptical deformation marks also associated with Al₂O₃ debris. Both Al₂O₃ and Si particles are efficient abrasive material, which associated with slight relative motion of metallic surfaces (clamp/strand and strand/strand) can promote fretting wear. Two types of fracture surface of the Al strands were identified: 45° and quasi-normal surfaces, the former being the predominant type. Delamination and particle detachment were the mechanisms of superficial degradation observed on the Al strands, indicating that the rupture of the strands occurred under a gross slip fretting regime induced by sub-conductor oscillation. Inspection of the internal surface of as-cast Al–10%Si spacer clamps revealed different stages of intense circumferential wear caused by the preferential cracking and particle detachment of the eutectic constituent of the as-cast microstructure. This intense wear reduces the clamping contact pressure, which allows higher displacement amplitude and leads to the critical fretting regime. Finally, a few suggestions are discussed to minimise the occurrence of future failures.     

沥青油毡瓦国内外标准对比分析

从范围、原材料要求、组分要求、物理力学性能等方面对比分析了我国现行油毡瓦标准与欧美标准的区别,提出了我国制订沥青油毡瓦国家标准的的原则。     

测井新技术在四川油气勘探开发中的应用

综述随着四川盆地油气勘探深入所面临的油气领域复杂和困难的技术问题，介绍应用测井新技术为四川油气开发解决了大量的技术难题，特别是在复杂缝，洞型储层的评价，井旁地质构造形态精细分析和地质，测井，地震多学科结合储层横向预测等3个方面所取得的良好应用效果。     

宝钢研制的全氢罩式炉控制系统分析

对宝钢研制的全氢罩式炉计算机控制系统的逻辑结构、工作原理及硬件配置进行了分析.该系统与引进的系统相比,在通讯方式、程序结构、操作分析、报警和开放性等方面都有所改进.     

双河油田特高含水后期开发阶段注采结构调整的实践与应用

针对双河油田的注采结构的现状及特征,通过近几年来在注采结构调整方面的实践与应用,总结出了油田在特高含水后期开发阶段,实现油田控水稳油目标的途径和方法,注水结构调整主要是结合地质特点,减少欠注层段,减少和控制不合理超注井层段和改善吸水剖面;在采液结构调整上,控制高含水层段的注入,加强中低渗透层段的注入,封堵高渗透、高水淹干扰层段,解放动用较差的中低渗透层段,改善平面上采出不平衡的状况。通过实施注采结构调整,双河油田在特高含水后期实现了高效开发。