Diamond-like carbon thin films by microwave surface-wave plasma CVD aimed for the application of photovoltaic solar cells

The nitrogen doped diamond-like carbon (DLC) thin films were deposited on quartz and silicon substrates by a newly developed microwave surface-wave plasma chemical vapor deposition, aiming the application of the films for photovoltaic solar cells. For film deposition, we used argon as carrier gas, nitrogen as dopant and hydrocarbon source gases, such as camphor (C₁₀H₁₆O) dissolved with ethyl alcohol (C₂H₅OH), methane (CH₄), ethylene (C₂H₄) and acetylene (C₂H₂). The optical and electrical properties of the films were studied using X-ray photoelectron spectroscopy, Nanopics 2100/NPX200 surface profiler, UV/VIS/NIR spectroscopy, atomic force microscope, electrical conductivity and solar simulator measurements. The optical band gap of the films has been lowered from 3.1 to 2.4 eV by nitrogen doping, and from 2.65 to 1.9 eV by experimenting with different hydrocarbon source gases. The nitrogen doped (flow rate: 5 sccm; atomic fraction: 5.16%) film shows semiconducting properties in dark (i.e. 8.1 × 10^{− 4} Ω^{− 1} cm^{− 1}) and under the light illumination (i.e. 9.9 × 10^{− 4} Ω^{− 1} cm^{− 1}). The surface morphology of the both undoped and nitrogen doped films are found to be very smooth (RMS roughness ≤ 0.5 nm). The preliminary investigation on photovoltaic properties of DLC (nitrogen doped)/p-Si structure show that open-circuit voltage of 223 mV and short-circuit current density of 8.3 × 10^{− 3} mA/cm². The power conversion efficiency and fill factor of this structure were found to be 3.6 × 10^{− 4}% and 17.9%, respectively. The use of DLC in photovoltaic solar cells is still in its infancy due to the complicated microstructure of carbon bondings, high defect density, low photoconductivity and difficulties in controlling conduction type. Our research work is in progress to realize cheap, reasonably high efficiency and environmental friendly DLC-based photovoltaic solar cells in the future.     

Numerical study of the transfer of shock-wave loading to a screened flat wall through a layer of a powdered medium and a subsequent air gap

The two-velocity, two-temperature model with two stresses in a mixture of a gas and solid particles contacting each other is used to numerically study the dynamic effect of an air shock wave incoming onto a solid wall with a screening layer of a porous powdered medium at some distance from the wall. The process is described for the case of one-dimensional planar motion of the gaseous and disperse phases under the assumption of a viscoelastic behavior of the powder skeleton. The effect of stepwise shock waves onto the porous powdered screen is considered. The influence of parameters of the screening layer and the air gap on the dynamics of loading of the screened solid wall is analyzed. __________ Translated from Fizika Goreniya i Vzryva, Vol. 43, No. 1, pp. 132–142, January–February, 2007.     

Synthesis of nitrogen incorporated diamond-like carbon thin films using microwave surface-wave plasma CVD

Nitrogenated diamond-like (DLC:N) carbon thin films have been deposited by microwave surface wave plasma chemical vapor deposition on silicon and quartz substrates, using argon gas, camphor dissolved in ethyl alcohol composition and nitrogen as plasma source. The deposited DLC:N films were characterized for their chemical, optical, structural and electrical properties through X-ray photoelectron spectroscopy, UV/VIS/NIR spectroscopy, Raman spectroscopy, atomic force microscope and current–voltage characteristics. Optical band gap decreased (2.7 to 2.4 eV) with increasing Ar gas flow rate. The photovoltaic measurements of DLC:N / p-Si structure show that the open-circuit voltage (V_oc) of 168.8 mV and a short-circuit current density (J_sc) of 8.4 μA/cm² under light illumination (AM 1.5 100 mW/cm²). The energy conversion efficiency and fill factor were found to be 3.4 × 10^{− 4}% and 0.238 respectively.     

Understanding heterogeneous catalysis on an atomic scale: a combined surface science and reactivity investigation for the dehydrogenation of ethylbenzene over iron oxide catalysts

In order to study the dehydrogenation of ethylbenzene to styrene, epitaxial iron oxide model catalyst films with Fe₃O₄(111), -Fe₂O₃(0001) and KFe _x O _y (111) stoichiometry were prepared in single crystal quality on Pt(111). They were investigated using surface science techniques before and after atmospheric pressure reaction experiments in a newly designed single crystal flow reactor. As expected from low-pressure measurements, Fe₃O₄(111) is catalytically inactive. The catalytic activity of -Fe₂O₃(0001) starts after an activation period of about 45 min. After that, the surface is essentially clean but shows a high concentration of defects. On the potassium-promoted films, however, the activation period is much longer, the activity then is higher and the surface gets covered completely with carbon and oxygen during reaction. This indicates a different reaction pathway on the promoted films with a carbon–oxygen species as catalytically active species.     

A simple planar monopole UWB slot antenna with dual independently and reconfigurable band‐notched characteristics

An extremely simple and compact planar monopole ultrawideband (UWB) slot antenna with dual band‐notched characteristics is proposed. The antenna is composed of a circular radiation patch, a microstrip‐fed line, and a partial ground. By etching an arc‐shaped slot on the radiation patch and a C‐like slot on the feed line, dual notched frequency bands at 3.3–3.7 GHz for WiMAX and 5.15–5.825 GHz for WLAN are achieved. And, the two notched bands can be adjusted independently by varying the length of the slots. Moreover, the band‐notched characteristics can be reconfigurable by shorting the corresponding slots. So, the antenna is capable of operating in one of multiple modes which makes it an excellent candidate for UWB applications. Meanwhile, experimental results indicate that the antenna has an available impendence bandwidth from 2.9 to 11 GHz which covers the UWB frequency band, and nearly omnidirectional patterns, stable gains, small group delay in operating band except rejected bands. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:706–712, 2014.     

Dynamic deviation reduction‐based concurrent dual‐band digital predistortion

This article introduces the concurrent dual‐band digital predistortion (DPD) architecture with only one upconvertion unit, which is suitable for the linearization of wideband power amplifiers (PAs) excited by concurrent dual‐band signals. By extending the conventional dynamic deviation reduction (DDR) model to the concurrent dual‐band mode, we propose two DDR‐based concurrent dual‐band models, the dual‐band DDR (DB‐DDR) model and the simplified dual‐band DDR (SDB‐DDR) model. The performance of these two models is experimentally assessed with two types of wideband PAs (a GaN Class F PA and a GaN Doherty PA) driven by the concurrent dual‐band signal, and compared with the prior two‐dimensional digital predistortion (2D‐DPD) model and the two‐dimensional modified memory polynomial (2D‐MMP) model. The results prove the good DPD performance and low computational complexity of the proposed models. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:401–411, 2014.     

A novel triple notch‐bands ultra wide‐band band‐pass filters using parallel multi‐mode resonators and CSRRs

This article discusses a technique based on combination of multimode resonators (MMR) and complementary split ring resonators (CSRR) to design multi notch‐bands ultra wide‐band (UWB) band‐pass filters (BPF). The proposed structure consists of two parallel multimode resonators, resulting in a dual notch‐band UWB BPF, integrated with a single cell of CSRR to realize the third notch‐band. The mechanism of realizing the notch‐bands is mathematically presented and a triple notch‐bands UWB BPF is designed, simulated and fabricated. The overall size of the proposed filter is reported to be around 36 × 7.7 mm² where a size reduction of around 35% is demonstrated in comparison to the conventional filter. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:375–381, 2014.     

闪火条件下防火服装热收缩形变的数据挖掘

随着暖体假人、燃烧假人、三维扫描仪等服装设备的应用,服装工程的大样本实验产生了大量数据,采用传统的数据分析方法未能发挥实验中大样本量的优势。本研究利用 Clementine 软件,选取了合适的分析方法,对防火服装的形变等有关数据进行了数据挖掘的尝试。首先通过变量重要性分析,研究了热收缩的重要影响因素,然后根据决策树与神经网络的变量重要性排序,提取了影响热收缩的关键因素,并进一步通过对热收缩及关键影响因素的聚类分析,探索了防火服不同部位区域的热防护特点。研究发现,热流量及衣下空气层是影响热收缩形变的关键因素,手臂及腿部对应服装部位需重点防护,数据挖掘技术是探索服装舒适性与功能机制与特点的有效工具。     

宽厚板厚度控制模型的优化

宽厚板厚度控制的目的是轧制出板形良好、板凸度小、同板差和异板差尽可能小的产品.莱钢宽厚板生产线自投人生产以来,在板凸度、厚度的均匀性、同板差和异板差等宽厚板厚度控制的瓶颈问题上都难以达到要求.为了实现对轧制厚度的要求,我们在现有的厚度控制模型的基础上,深入理解其控制功能、补偿功能的作用,找到引起厚度难以控制的主要因素,采取轧辊刚度补偿、轧辊偏心补偿、支撑辊油膜厚度补偿、工作辊热膨胀补偿及冲击力补偿等措施来优化厚度控制模型.自优化相应厚度参数和增加相关补偿控制功能以来,宽厚板厚度控制的精度得到很大的提高,具有很高的推广价值.     

LC GRIN lens mode with wide viewing angle for rotatable 2D/3D tablet

To widen the vertical and horizontal angular ranges where the lens performs well, the off‐axis performance of a liquid crystal gradient index (LC GRIN) lens is analyzed by the combined simulation system of an LC director simulator and a ray‐tracing simulator. We found that the angular difference between an LC alignment direction and an electrode array direction of the LC GRIN lens is one of significant parameters, and detailed conditions of structure are established. The measurement result shows that the developed structure reduces the degradation ratio in a luminance profile from 61% to 3.2%. We have applied a user tracking system for the rotatable 3D display, equipped with a detection of a panel orientation and a face position. As a result, we have developed a rotatable 2D/3D tablet whose 3D viewing azimuth angle is over 30° in both landscape and portrait orientations.