C6711 DSP和PC的HPI-USB2.0通讯链路设计

随着性能指标的提高,嵌入式系统中DSP的测试工作也日趋复杂,需要以高速率低资源占用的接口和上位机通讯。HPI可在不影响DSP主程序运行的情况下发送数据,USB2.0则可以较高的速度将数据转发给PC,HPI-USB2.0通讯链路结合了两者的优点,以简洁的硬件和软件,很好地满足了DSP的测试需求。     

IP/MPLS over WDM网络生存性的研究

该文首先分析了IP/MPLS over WDM网络单层生存性和多层联合生存性,并就生存性策略的性能进行对比,然后对多层空闲资源分配进行了研究。     

用VB、VBA增强Word97 功能

本文应用ＶＢ６．０制作的动态链接库（ｄ１１）、Ｗｏｒｄ Ｂａｓｉｃ,ＶＢＡ在Ｗｏｒｄ９７中自动形成文档,增强了Ｗｏｒｄ９７的功能。     

套缸式高空作业车摆臂机构机构综合分析

为选择机构的合理结构形式、运动副类型、数目及合理的尺寸搭配,对一种高空作业车摆臂机构进行分析.在已知连杆铰接点的起始位置、连架杆的对应转角及机架长度的平面综合连杆机构的各设计变量间关系的条件下,根据给定的运动学或动力学要求,进行了机构综合.对六杆运动链连杆类配方案进行选择,组合生成六连杆4种形式,在此基础上再生运动链,形成新的机构形式,给出机构多种可能的构型,完成摆臂机构的型综合.对不同方案进行比较,得出了满足运动学及动力学要求的最优解.     

宽频功分移相器性能仿真分析

采用威尔金森(Wilkinson)功分器和宽带移相器级联的馈电网络具有良好的功分移相特性,可用于多模导航天线的设计.首先对馈电网络的宽带移相器进行了理论分析,然后采用HFSS软件对其短路及开路支节的参数进行了仿真,分析了其参数变化对馈电网络功分及移相特性的影响.仿真结果表明,优化参数的尺度可使馈电网络获得更宽的功分移相特性.     

高频环节AC/AC变换器在电网补偿中的应用研究

为消除电网中的谐波对电网质量的影响,将单周期控制技术应用于带Z源的高频环节AC/AC变换器,建立了基于该变换器的电网补偿系统.通过AC/AC变换器,产生与电网相位相反的三倍频正弦波,以抑制电网中的三次谐波.最后利用Simulink工具进行了仿真验证.仿真结果表明,电网总谐波畸变度（THD）由7.21%降到补偿后的0.54%,实现了电网的谐波补偿.     

S波段宽带微波固态功率放大器的设计

微波功率放大器是发射机的重要组件,它的设计成了微波发射系统的关键.文中使用ADS仿真软件对一款功率放大器进行电路设计和仿真,根据晶体管的小信号S参数和I-V曲线,对功率管的输入、输出阻抗匹配电路及其偏置电路进行优化设计,使其性能达到设计要求.在2～2.5GHz的频段内,对输入功率为0dBm射频信号,使用功放模块可以输出40dBm的射频信号,带内波动≤±1.5dB.     

The effects of horizontal load speed and lifting frequency on lifting technique and biomechanics

Lifting loads that have a horizontal velocity (e.g. lifting from a conveyor) is often seen in industry and it was hypothesised that the inertial characteristics of these loads may influence lifting technique and low back stress. Seventeen male participants were asked to perform lifting tasks under conditions of four horizontal load speeds (0 m/s, 0.7 m/s, 1.3 m/s and 2.4 m/s) and two lifting frequencies (10 and 20 lifts/min) while trunk motions and trunk muscle activation levels were monitored. Results revealed that increasing horizontal load speed from 0 m/s to 2.4 m/s resulted in an increase in peak sagittal angle (73° vs. 81°) but lower levels of peak sagittal plane angular acceleration (480°/s² vs. 4°/s²) and peak transverse plane angular acceleration (200°/s per s vs. 140°/s per s) and a consistent increase in trunk muscle co-activation. Participants used the inertia of the load to reduce the peak dynamics of the lifting motion at a cost of increased trunk flexion and higher muscle activity.

Statement of Relevance: Conveyors are ubiquitous in industry and understanding the effects of horizontal load speed on the lifting motions performed by workers lifting items from these conveyors may provide some insight into low back injury risk posed by these tasks.     

Hand-hold location and trunk kinematics during box handling

Trunk kinematics variables have been shown to be related to low back injury risk during lifting tasks and it was hypothesised that changes in hand-hold positions could influence trunk kinematics and thereby risk. Fourteen subjects lifted a 5 or 10 kg box using four different hand placement locations (two symmetric and two asymmetric) while their trunk kinematics (position, velocity and acceleration in the sagittal, coronal and transverse planes) were captured using the lumbar motion monitor (LMM). These kinematics data were then used to calculate the probability of high risk group membership (PHRGM) as defined in the LMM risk assessment model. The results showed significant effects of hand placement on trunk kinematics, resulting in significant changes in the PHRGM variable ranging from a low of 20% in a the symmetric low load condition to a high of 38% under the asymmetric, 10 kg condition.

Statement of Relevance: Manual materials handlers use a variety of hand-hold positions on boxes during lifting. Where a lifter grabs the box can influence the trunk kinematics during the lifting task and these kinematics have been shown to provide some insight into risk of low back injury. This study documents the trunk postures and kinematics as a function of hand-hold position.     

建筑类院校电气信息类专业教学管理工作探析

本文以电气信息类专业为例,阐述了高校院（系）教学管理工作的性质与功能,提出采用环节控制方法解决教学管理工作中存在的问题.该方法具有一定的可行性和可操作性,为院（系）教学管理工作提供借鉴.