Understanding and Modeling the Effect of Surfactants in Enhanced Particle Removal from Surfaces in Aqueous Media

The removal of particulate contamination is a critical issue for many manufacturing processes. It is particularly critical to the electronics industry in which small pieces of microscopic debris remaining after chemical mechanical planarization (cmp) using submicron polishing particles can cause device failure. One way to enhance particle removal following the cmp process is to utilize surfactants. Recent research has shown ways to model the effect of surfactants on enhanced particle removal. However, previous research has not demonstrated the effect of ionic strength on enhanced particle removal associated with surfactant use. Past research has also not shown the combined effects of ionic strength and surfactant concentration on enhanced particle removal using surfactants. This article summarizes the parameters affecting particle removal, and it provides data and analysis on the effect of ionic strength as well as the combined effects of ionic strength and surfactant concentration on particle removal following cmp processing.     

Schwingfestigkeit von Schraube‐Mutter‐Verbindungen

High cycle fatigue of bolted connections Extensive tests regarding the influences on the fatigue of bolt‐nut‐connections of preloading with torsion, of preloading with yielding, of loading with superimposed bending and of the tested lot are processed. These influences are not yet known according to VDI 2230. New testing devices were designed for these tests, which allow a far less expensive operation and may easily be used for bolts of diameters up to M100 and testing frequencies up to 1000 Hz. The validity of fatigue resistance according to VDI 2230 is specified with respect to the test results. The determined influence of the tested lots is unexpectedly high. The manufacturing process of bolts should be improved to minimize this influence.     

Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

Exchange and oxidation of CO on O-predosed Rh---Al2O3 and Rh---CeO2 catalysts

Exchange and oxidation of C¹⁶O were investigated at 450°C on ¹⁸O-predosed Rh and Pt catalysts supported on A1₂O₃, CeO₂ and CeO₂-Al₂O₃. In all cases, a rapid exchange of C¹⁶O with the surface can be observed. CO oxidation leads to C¹⁶O₂, C¹⁶O¹⁸O and C¹⁸O₂. Significant formation of C¹⁶O₂ is due to the relatively high ¹⁶O coverage in reaction resulting from the C¹⁶O exchange and from an exchange between O surface species and ¹⁶O internal atoms. Hydrogen is also formed via a water-gas shift reaction (CO + surface OH) in higher proportion on CeO₂-containing catalysts than on A1₂O₃. Chlorine inhibits all the reactions (exchange, oxidation and WGS) and particularly the internal exchange.     

Determination of the width of the transition layer between the crystalline and amorphous zones in nylon 1010 by SAXS

The width of the transition layer between the crystalline and amorphous zones in nylon 1010 was determined by SAXS with point collimation and long-slit collimation, respectively. The width of the transition layer, E, was found to be 1.7 nm. The results show that the width of the transition layer is independent of crystallinity.     

Instron texture profile of buffalo milk cheddar cheese as influenced by composition and ripening changes

Buffalo milk Cheddar cheese samples of different ages were analysed for compositional attributes (CA), ripening indices (RI) and Instron Textural Profile (ITP). All samples were compositionally alike, except for pH and salt-in-moisture (SM) contents. RI showed significant variations. CA and RI showed highly significant correlations within themselves and with each other, except for moisture with pH, SM with moisture, MNFS, Fat and FDM and Fat with MNFS. The ITPs of cheeses showed significant variations and had highly significant intercorrelations indicating their interdependence. CA (except moisture and MNFS) and RI showed a highly significant correlationship with ITPs. Moisture content showed a highly significant correlationship with all ITPs, except cohesiveness and springiness, where it was significant. MNFS content showed significant correlations only with hardness and brittleness. Stepwise regression analysis revealed that MI was the most predominant factor influencing cheese texture, followed by pH, SM, FDM and TVFA. Knowing Ca and RI, the textural properties of cheeses can be forecast through mathematical equations. Similarly the age of cheese can also be predicted if RI and/or textural properties are known.     

Community OR — Five Years of Organised Activities and Beyond

What has become known as Community Operational Research has been around in the UK for many years. The election of Jonathan Rosenhead as President of the UK OR Society in 1986–87 was the catalyst for bringing together and expanding activities which had been carried out largely by individuals working in isolation on a voluntary basis. The following five years have seen the establishment of the Community OR Unit at Northern College, the Centre for Community OR at Hull University and the Community OR Network, which supports the activities of volunteer OR workers across the UK. This paper reviews the range and types of work which have been undertaken by various practitioners. An assessment of the success of community OR is made and a number of issues which have arisen are discussed. Finally, given the diverse nature of community OR, its practice and practitioners, there is some discussion about the future of the area.