Development and validation of a micro-fin tubes evaporator model using R134a and R1234yf as working fluids

This paper presents a model of shell and tube evaporator with micro-fin tubes using R1234yf and R134a. The model developed for this evaporator uses the ε-NTU method to predict the evaporating pressure, the refrigerant outlet enthalpy and the outlet temperature of the secondary fluid. The model accuracy is evaluated using different two-phase flow boiling correlations for micro-fin tubes and comparing predicted and experimental data. The experimental tests were carried out for a wide range of operating conditions using R134a and R1234yf as working fluids. The predicted parameter with maximum deviations, between the predicted and experimental data, is the evaporating pressure. The correlation of Akhavan– Behabadi et al. was used to predict flow boiling heat transfer, with an error on cooling capacity prediction below 5%. Simulations, carried out with this validated model, show that the overall heat transfer coefficient of R1234yf has a maximum decrease of 10% compared with R134a.     

Eine Definitionssprache für die Kommunikationsverbindungen in verteilten Automatisierungssystemen

Eingegangen am 13.11.1996, in überarbeiteter Form am 12.5.1997     

Biaxiale Ermüdung reibrührgeschweißter Strukturelemente

Biaxial fatigue of friction stir welded stiffened panels Within the framework of the European WelAir project, cruciform specimens made from stiffening FSW overlap joints were fatigued in the DLR biaxial test rig. To resemble the loading situation of pressurized fuselage structures, proportional loading without any phase shift, but with different load ratios λ between the loading components in both directions was applied.Natural crack initiation and subsequent crack growth were governed by the stiffness gradient caused by introducing the stringer. Cracks initiated and propagated at run‐in and run‐out locations in a direction perpendicular to the weld seam. The shortest fatigue life was observed for uniaxial loading in welding direction (λ = 0). An additional stress component perpendicular to the joint line (λ > 0) resulted in a higher number of cycles to failure. Similar to single stringer panels, increasing the load ratio also increased the number of cycles to failure for FSW clip‐stringer structural members, but additionally gives a different location of the fatal crack.     

Eine Produktions-/Lagerhaltungspolitik bei stochastischer Nachfrage im Mehrproduktfall

Zusammenfassung Eine Lagerzielmengenpolitik für den Fall intermittierender Fertigung mehrerer Sorten auf einer Anlage bei stochastischer Nachfrage wird durch ein Warteschlangenmodell abgebildet. Für die sich ergebenden Kostenfunktion wird eine Approximation vorgeschlagen. Die Bestimmung optimaler Losgrößen und Lagerzielmengen wird untersucht.     

Abstimmung von Produktions- und Transportlosgrößen zwischen Zulieferer und Produzent

Es wird eine Erweiterung des mehrstufigen stationären Losgrößenproblems mit endlichen Produktionsgeschwindigkeiten um den zeitpunktgeballten Transportvorgang vorgestellt. Diese Darstellung gibt die Beziehungen zwischen Zulieferer, Transporteur und Produzent adäquat wieder. Hinsichtlich der Abstimmung der Entscheidungsgrößen dieser organisatorischen Einheiten wird zwischen einer rein simultanen, einer rein sukzessiven sowie zweier gemischt simultan-sukzessiver Koordinationsarten unterschieden. An Hand einer analytischen Untersuchung werden Unterschiede und Gemeinsamkeiten der jeweiligen Entscheidungsgrößen und der daraus resultierenden Kostenfunktionen dargestellt. Schließlich zeigt eine numerische Analyse die Gesamtkostenunterschiede zwischen der rein simultanen und rein sukzessiven Koordinationsart auf.An extension is introduced to the multi-stage stationary lot-sizing problem with finite production rates by the time-concentrated transportation-process. This representation adequately demonstrates the relations between supplier, carrier and producer. With regard to the reconciliation of the decision variables of these institutional units one differentiates between a pure simultaneous, a pure gradual and two mixed simultaneous-gradual coordination methods. The differences and correspondences of the respective decision variables and the resulting cost functions are demonstrated by means of an analytical examination. Finally, a numerical analysis shows the distinctions in total cost between the pure simultaneous and pure gradual coordination method.     

Espaces métriques rationnellement présentés et complexité, le cas de l'espace des fonctions réelles uniformément continues sur un intervalle compact

We define the notion of rational presentation of a complete metric space, in order to study metric spaces from the algorithmic complexity point of view. In this setting, we study some representations of the space C[0,1] of uniformly continuous real functions over [0,1] with the usual norm: ||f||_∞ = Sup{|f(x)|; 0x1}. This allows us to have a comparison of global kind between complexity notions attached to these presentations. In particular, we get a generalization of Hoover's results concerning the Weierstrass approximation theorem in polynomial time. We get also a generalization of previous results on analytic functions which are computable in polynomial time.     

(Cr1‐x,Alx)N ein Review über ein vielseitig einsetzbares Schichtsystem

(Cr_1‐x,Al_x)N a review about a multi‐purpose coating system Nitride based coatings claimed a big market share for PVD‐coatings. Especially in the field for high temperature die casting and cutting operations chromium based coatings are well used. These coatings are also used in low temperature processes for the coating of machine parts. In the beginning of the nineties first examinations are done on the ternary system Chromium‐Aluminium‐Nitride. This system shows an excellent corrosion behaviour against many different liquids, but gains also a high hardness for a good wear behaviour. By changing the AlN to CrN content and the coating design CrAlN opens up a wide range for different coating applications. A major step for machine parts was the reducing of coating process temperature beneath 200 °C. This was only possible by using pulsed power supplies. CrAlN shows a very good performance on the fast growing market of coated machine parts e.g. on spindle bearings.     

电除尘器智能管理软件的开发研究

文章以火电厂静电除尘器集散控制系统为研究对象,开发电除尘器智能管理软件.实现对电除尘器的实时监控;建立专家知识库,通过调用知识库内容对电除尘器进行故障在线判断;以烟气出口粉尘浊度值为依据,进行闭环控制,实现能量管理;根据煤种以及锅炉燃烧和运行工况对电除尘器进行效率预测.