全文获取类型
收费全文 | 3196篇 |
免费 | 171篇 |
国内免费 | 335篇 |
专业分类
电工技术 | 59篇 |
综合类 | 288篇 |
化学工业 | 978篇 |
金属工艺 | 781篇 |
机械仪表 | 72篇 |
建筑科学 | 126篇 |
矿业工程 | 60篇 |
能源动力 | 13篇 |
轻工业 | 75篇 |
水利工程 | 5篇 |
石油天然气 | 10篇 |
武器工业 | 18篇 |
无线电 | 254篇 |
一般工业技术 | 586篇 |
冶金工业 | 363篇 |
原子能技术 | 11篇 |
自动化技术 | 3篇 |
出版年
2024年 | 6篇 |
2023年 | 58篇 |
2022年 | 62篇 |
2021年 | 68篇 |
2020年 | 51篇 |
2019年 | 54篇 |
2018年 | 36篇 |
2017年 | 53篇 |
2016年 | 53篇 |
2015年 | 71篇 |
2014年 | 122篇 |
2013年 | 96篇 |
2012年 | 127篇 |
2011年 | 112篇 |
2010年 | 130篇 |
2009年 | 158篇 |
2008年 | 204篇 |
2007年 | 248篇 |
2006年 | 247篇 |
2005年 | 192篇 |
2004年 | 262篇 |
2003年 | 163篇 |
2002年 | 154篇 |
2001年 | 113篇 |
2000年 | 119篇 |
1999年 | 83篇 |
1998年 | 91篇 |
1997年 | 86篇 |
1996年 | 83篇 |
1995年 | 92篇 |
1994年 | 75篇 |
1993年 | 65篇 |
1992年 | 51篇 |
1991年 | 41篇 |
1990年 | 42篇 |
1989年 | 25篇 |
1988年 | 5篇 |
1987年 | 2篇 |
1986年 | 2篇 |
排序方式: 共有3702条查询结果,搜索用时 15 毫秒
891.
892.
评估了陶瓷工业用后的、硅酸盐结合SiC板重复使用于陶瓷工业和钢工业的情况。准备了几批含不同量矾土和硅灰的、使用过的SiC质板作试验料,加热到1400℃。通过检测体积密度和显气孔率来测试料的致密性。研究了这些烧结材料的矿物性能和显微结构,这些性能与30次热震实验后耐压强度同热震实验前的耐压强度比值有关。莫来石的形成、莫来石代替碳化硅和假碳化硅的生成、碳化硅的紧密结构和良好分布等都被记录。随着不断增加的莫来石含量直至40%,热震实验后强度同实验前强度相比有所增大。将料加热到950℃再用水冷处理,如此循环30次后观测发现,所有批次的料抗热震性能良好,没有剥落出现。 相似文献
893.
本文阐述了氧化铝瓷的密度、磨耗与生产工艺的关系,结合其显微结构分析了浆料、造粒粉料对产品质量的影响。 相似文献
894.
LI Wei 《钢铁研究学报(英文版)》2007,14(3):47-50
A great amount of iron grinding balls in tube mills have been consumed. Under this impact abrasive wear working condition, the failure of wear resistant alloying white irons grinding balls is mainly caused by fatigue spalling. The impact wear resistance of martensitic high chromium cast iron (Cr of 15%) is not high sometimes, but its cost is not low. Thus, medium Cr-Si wear resistant cast iron is recommended. The influence of the iron on impact fatigue resistance and impact wear resistance is pronounced. Ball-on-ball impact fatigue test and high stress impact wear test of the grinding balls have been carried out. The results show that the impact fatigue resistance (IFR) and impact wear resistance (IWR) of medium Cr-Si cast iron are superior to those of martensitic high chromium cast iron (Cr of 15%). The main reasons are that (1) the stress in medium Cr-Si cast iron is released in the as-cast state; (2) the matrix is fine pearlite with better toughness and plasticity; (3) the pearlite is more stable compared with a retained austenite under repeated impact load and less phase transformation can take place; (4) high silicon content im- proves the morphology of eutectic carbide; (5) there is no seeondary carbide which results in less crack sources. All these factors are beneficial to improvement of impact fatigue spalling resistance. The eutectic carbide M7C3 is the main constituent to resist wear. 相似文献
895.
LIU Qingcai LIU Qingyou LIU Yi 《中国耐火材料》2006,15(1):25-29
1 Introduction The corrosion resistance of the refractories is one of the imperative problems for the development of smel- ting reduction with iron bath[1 ~4]. The Al2O3-C based refractories have been widely and successfully used in the metallurgy industr… 相似文献
896.
897.
898.
899.