滴丸动力黏度的实验研究

复方丹参滴丸是治疗冠心病等疾病的纯中药固体制剂.在滴丸滴制时,滴丸的动力黏度影响滴丸成品的外观质量,如圆整度、硬度、大小和干裂度等.本文研究复方丹参滴丸制剂的含水率和溶化温度对滴丸动力黏度的影响.通过实验测定和数据分析得出,滴丸制剂的溶化温度在75℃~85℃,滴丸制剂含水率为6%~10%的条件下,滴丸的动力黏度值基本恒定,滴丸的滴制效果最佳.实验结果已经用于制订新的生产工艺,指导实际药品的生产.     

模具沉积层应变的模拟

为分析沉积层应变的变化情况,并找出温度与形变的变化规律,采用有限元分析软件ANSYS计算并绘制不同时刻以及不同位置沉积层内的温度及应力应变曲线,在建立传热模型过程中考虑了金属液滴向沉积层的传热以及沉积层向系统外的热量散失等问题．采用在厚度方向以微小层逐层叠加来模拟涂层的增厚,并以此为基础构造沉积层有限元计算模型,应用单元生与死逐层激活层单元参与计算过程．实现移动边界以充分模拟真实的喷涂沉积过程．通过分析不同时刻以及不同位置沉积层内的应力应变曲线,获得了沉积层应力应变变化规律．结果表明,沉积层内存在残余塑性应变,且沉积层与母模接触部位等效应力最大,是最易翘曲的地方,验证了沉积层失稳的一般形式．     

某水电站拱坝施工期温度仿真分析

拱坝施工期的温控防裂研究是设计和施工期需要特别关注的问题之一.采用三维有限单元法对某水电站拱坝碾压混凝土坝段和常态混凝土坝段的施工期温度场进行仿真分析.计算结果表明,薄层浇筑的层面散热效果好,层厚超过3 m后效果不明显;不同季节的层面散热效果差异较大,浇筑气温越低,层面散热效果越好;常态混凝土溢流坝段自由冷却时间较长,须采取坝体二期冷却措施,以保证按期进行接缝灌浆.     

Relaxation and Dielectric Characteristics of Zn Substituted Copper-gallate Ferrite

The dielectric permittivities(ε'&ε")and dielectric loss tangent(tan)are studied for the prepared samples CuFe2O4 and Cu1-xZnxGa0.1 Fe1.9 O4 spinel ferrites with (0.0≤x≤0.5)from room temperature up to 700K in the frequency range(102～105Hz).Dielectric anomaly at the transition temperature Tc is pronounced in the relations of dielectric permittivitties with temperature where,the obtained Tc is found to decrease linearly with increasing Zn concentration.The relation of tan with frequency at different temperatures shows relaxation spectra where the relaxation time and the maximum frequency of the hopping conduction mechanism are determined.The variation of(ε',ε"and tanδ)with frequency and temperature displays a strong dependence on both gallium and zinc concentrations.The results are explained in light of the cation-anion-cation and cation-cation interactions over the octahedral sites in the spinel structure.     

核电SA508-3钢在不同冷速下的显微组织

针对由某公司生产首次应用到核电上的SA508-3钢,采用膨胀法在Gleeble1500D热模拟机上测定了其焊接连续冷却转变的膨胀曲线,结合显微组织和硬度,获得了每个冷速下对应的相变点温度.结果表明,在0.015～0.05℃/s冷速范围内.为高温转变的铁素体和珠光体区,0.1～7℃/s冷速范围内,为中温转变的贝氏体区,20～80℃/s的冷速范围内,为低温转变的马氏体区;随着冷却速度的增大,硬度值也越来越大,0.015℃/s对应的硬度值为199 HV,80℃/s对应的硬度值为546 HV,这为制定合理的焊接工艺提供了依据.     

Hot-compression behavior of Al-1Mn-1Mg alloy

The hot-compression of Al-1Mn-1Mg (mass fraction, %) alloy sample was carried out on a Gleeble-1500 thermo-simulator at deformation temperatures from 320 to 400 ℃ and strain rates from 0.1 to 10 s-1 by total strain of 1.4. Microstructure and texture evolution of the hot-compressed alloy were investigated by optical microscopy and X-ray diffraction analysis, respectively. The results show that the relationship among flow stress σ, deformation temperature T and strain rate ε can be expressed in the form of βσ...     

Numerical analysis on thermal regime in double-loop channel inductor

In order to investigate the temperature distribution, a three-dimensional finite element model (FEM) was developed to simulate the temperature regime in the channels of double-loop inductor, and the simulated results were compared with experimental data from low load trials of a 400 kW inductor. The results of numerical simulations, such as the temperature and Joule heating rate, show reasonable correlation with experimental data. The results indicate that Joule heating rate and the temperature reach the maximum at the corners and the minimum at the centre of the cross-section area. The temperature difference between the inlet and outlet is in an inverse proportion to mass transport. Joule heating rate and the temperature are directly proportional to power frequency. It is concluded that mass transport and power frequency play a critical role in determining the temperature regime and Joule heating rate, the relative permeability of the magnetic core shows no significant influence on temperature regime and Joule heating rate, when the relative permeability varies from 5 000 to 10 000.     

Precipitation and stability of reversed austenite in 9Ni steel

A new method was used to analyze the factors affecting the precipitation of reversed austenite during tempering. The samples were kept at various tempering temperatures for 10 min and their length changes were recorded. Then, the precipitation of reversed austenite which led to the length reduction was shown by thermal expansion curves. The results show that the effects of process parameters on the precipitation of reversed austenite can be determined more accurately by this method than by X-ray diffraction...     

卷取温度对X80管线钢析出行为与性能的影响

观察了不同卷取温度下X80管线钢中析出物的情况,并结合其组织性能对比可知：在实验情况下,480℃卷取时,有大量细小弥散的Nb、V的碳氮化物析出物,起到了较好的析出强化作用.     

Si(111)上生长LiNbO_3薄膜的研究

利用射频磁控溅射的方法,在Si(111)衬底上制备了LiNbO3薄膜。采用X射线衍射(XRD)和扫描电子显微镜(SEM)研究了衬底温度、退火温度和溅射气体压强对LiNbO3薄膜结晶和表面形貌的影响,并用椭圆偏振仪测量了薄膜的厚度和折射率。结果表明:衬底温度为450℃时制备的薄膜,退火前后都没有LiNbO3相生成;衬底温度为500～600℃时,LiNbO3薄膜出现(012)、(104)和(116)面衍射峰,经600℃退火后3个衍射峰的强度加强;衬底温度为600℃时,经600～900℃退火得到的LiNbO3薄膜,除出现(012)、(104)和(116)面衍射峰外,还出现(006)面衍射峰;溅射气体压强从0.8 Pa增大到2.4 Pa时,经800℃退火后得到的LiNbO3薄膜表面晶粒团簇变小,而0.8 Pa制备的薄膜经800℃退火后LiNbO3相的结晶程度较其它压强下完善;900℃退火后得到的LiNbO3薄膜折射率为2.25,与LiNbO3晶体相当。