高Al2O3物料对镍电炉渣粘度的影响

论文对Al2O3高达69．46％的含镍物料电炉处理时对炉渣性能的影响进行了研究。研究表明：吉林镍业公司冶炼厂电炉渣1340℃时黏度为0．538P．s；电炉渣在不添加任何其它试剂的情况下，渣中Al2O3含量不宜高于9％；加入添加剂后，炉渣黏度降低，当在配料中加入20％此种含镍物料时，添加剂加入量7％为宜，此时炉渣黏度为0．74P．s（1340℃）。     

几种高性能汽车用铸造铝-硅合金

简要介绍国内应用于汽车工业的几种重要铸造铝合金的成分和性能，并与国外同类铸造铝合金的性能进行了对比。     

钨合金圆筒爆破试验破片分布的统计分析

采用圆筒爆破试验方法研究了易碎型钨合金的破片分布特征,并与93W合金的结果进行了对比.对破片的数量和质量分布特征进行了统计分析,发现易碎型钨合金的破片率明显高于93W合金,而且破片的均匀性也明显好于93W合金,但易碎钨合金的破片回收率低于93W合金,而且受装药量的影响较大.     

In-situ composite Cu-Cr contact cables with high strength and high conductivity

In order to develop a new type of contact cable with high strength and high electrical conductivity, Cu-Cr alloy series were selected as materials and Cu-Cr alloy castings were produced by means of directional solidification continuous casting (DSCC) process. The results show that the fibrillar strengthening phase, 13-Cr, orderly arranges among the copper matrix phase along the wire direction; and a microstructure of in-situ composite forms, which retains the basic property of good conductivity of the copper matrix and meanwhile obtains the strengthening effect of [3-Cr phase. The production technology as well as the mechanical property, electrical property, and synthetic property of the in-situ composite contact cables was discussed.     

NiTi形状记忆薄膜的显微结构和力学性能

NiTi形状记忆合金薄膜具有形状记忆效应，极有希望用于制造高技术领域微电子机械系统中的微型激发器。NiTi形状记忆合金薄膜在制备和使用过程中需要高品质（衬）底材。本文利用高分辨电子显微学和高分辨分析电子显微学详细研究了硅底材NiTi形状记忆合金薄膜的NiTi／Si和NiTi／SiO2微结构体系，包括薄膜精细结构和界面反应。也研究了其显微结构和力学性能的关系。特别给出了NiTi形状记忆合金薄膜产生疲劳过程的微观过程的起因，通过高达十万个使用热循环前后样品显微结构变化的比较，发现纳米尺度上的TiNi3新相的形成导致疲劳过程的发生。如何抑制TiNi3新相形成的研究正在进行之中，这将为进一步提高NiTi形状记忆合金的使用寿命指出方向。     

微晶合金在电流互感器中的应用

从微晶合金的性能特点出发，分析了其在电流互感器中的应用前景。     

Nucleation Mechanism for Bainite

Based on the experimental results that solute-depleted zone was observed in Cu-28Zn-4AI (mass fraction) at 523 K, AG is calculated as a positive according to the thermodynamic criteria for the spinodal decomposition of a ternary systems. So, the solute-depleted zone cannot be formed by spinodal decomposition. Dislocation density required by the formation of solute-depleted zone is estimated greater than 7.89×109 cm-2, according to the segregation of solute atoms around dislocations, which is not consistent with the practical situation for the alloy at 523 K. Associated with the internal friction experimental fact that internal friction peaks appear within the incubation for bainitic transformation in Cu-Zn-AI alloy, the equilibrium temperature, TO, is evaluated as 433 K for solute-depleted Cu-25Zn-3.4AI, which is lower than the experimental temperature 523 K. Thus, nucleation by shear mechanism is impossible in this circumstance. Therefore, it is concluded that, like bainite in steels and Ag-Cd, bainite in     

聚氯乙烯共混改性研究进展

介绍了近期国内外在聚氯乙烯（PVC）的共混改性领域内的研究和应用进展及其发展方向。     

单晶凝固组织的样品尺寸效应

通过对不同直径的单晶样品的凝固实验，研究了样品尺寸对单晶凝固组织的影响规律，研究发现，随样品尺寸减小，单晶凝固组织被细化，尤其一次枝晶间距λ1和枝晶间γ′相尺寸对样品尺寸的依赖性更为明显；样品尺寸影响的要质在于此表面积的变化，进而对凝固过程温度梯度产生影响，最终作用于凝固组织和力学性能，一次枝晶间距λ1和枝晶间γ′尺寸与样品的比表面积近拟呈线性关系，样品尺寸变化，明显改变了单晶生长过程的温度梯度和合金的高温持久寿命。