Catalytic Hydrocracking of a Bitumen‐Derived Asphaltene over NiMo/γ‐Al2O3 at Various Temperatures

Hydrocracking of a bitumen‐derived asphaltene over NiMo/γ‐Al₂O₃ was investigated in a microbatch reactor at varying temperatures. The molar kinetics of asphaltene cracking reaction was examined by fitting the experimental data. Below a defined temperature, the molar reaction showed the first‐order kinetic feature while at higher temperatures secondary reactions such as coke formation became significant, causing deviation of the reaction behavior from the proposed first‐order kinetic model. Selectivity analysis proved that dominant products varied from gases to liquids to gases with increasing temperature, shifting the dominant reaction from C–S bonds cleavage to C–C bonds cleavage.     

PMU based voltage security assessment of power systems exploiting principal component analysis and decision trees

The need for feature selection and dimension reduction is felt as a fundamental step in security assessment of large power systems in which the number of features representing the state of power grids dramatically increases. These large amounts of attributes are not proper to be used for computational intelligence (CI) techniques as inputs, because it may lead to a time consuming procedure with insufficient results and they are not suitable for on-line purposes and updates.This paper proposes a combined method for an online voltage security assessment in which the dimension of the token data from phasor measurement units (PMUs) is reduced by principal component analysis (PCA). Then, the features with different stability indices are put into several categories and feature selection is done by correlation analysis in each category. These selected features are then given to decision trees (DTs) for classification and security assessment of power systems.The method is applied to 39-bus test system and a part of Iran power grid. It is seen from the results that the DTs with reduced data have simpler splitting rules, better performance in saving time, reasonable DT error and they are more suitable for constant updates.     

A highly transparent and thermally stable copolymer of 1‐adamantyl methacrylate and styrene

Thermal and optical properties of copolymers of 1‐adamantyl methacrylate (AdMA) and styrene (St) prepared by free radical polymerization in the bulk are investigated. The copolymer forms an azeotrope when the composition is AdMA/St = 55/45 mol%. The glass transition temperature and decomposition temperature of the azeotropic copolymer are 170 and ca 340 °C, respectively. The refractive index increases nonlinearly with St content from 1.522 to 1.591. The light scattering loss at 633 nm is 28.1 dB km^?1, which is less than half of that of polystyrene. The total optical loss including molecular vibrational absorption, which is evaluated using a copolymer‐based optical fiber, is 292–645 dB km^?1 at 500–700 nm. These values correspond to transmittances of 86–93% for a 1 m optical path length. © 2014 Society of Chemical Industry     

Low cycle fatigue behavior of a eutectic 80Au/20Sn solder alloy

The eutectic 80Au/20Sn solder alloy is widely used in high power electronics and optoelectronics packaging. In this study, low cycle fatigue behavior of a eutectic 80Au/20Sn solder alloy is reported. The 80Au/20Sn solder shows a quasi-static fracture characteristic at high strain rates, and then gradually transforms from a transgranular fracture (dominated by fatigue damage) to intergranular fracture (dominated by creep damage) at low strain rates with increasing temperature. Coffin-Manson and Morrow models are proposed to evaluate the low cycle fatigue behavior of the 80Au/20Sn solder. Besides, the 80Au/20Sn solder has enhanced fatigue resistance compared to the 63Sn/37Pb solder.     

一款紧凑增强型可变阻抗电磁带隙结构

基于传统AI-EBG结构,提出了一种小尺寸的增强型电磁带隙结构,实现了从0.5~9.4 GHz的宽频带-40 dB噪声抑制深度,且下截止频率减少到数百MHz,可有效抑制多层PCB板间地弹噪声。文中同时研究了EBG结构在高速电路应用时的信号完整性问题,使用差分信号方案可改善信号完整性。     

Soret and Dufour effects between two rectangular plane walls with heat source/sink

This study addresses the thermo‐diffusion and the diffusion‐thermo phenomena in a semi‐infinite absorbent channel whose walls are contracting/expanding, with heat source/sink effects. The governing partial differential equations with suitable boundary conditions are transformed to a system of dimensionless ordinary differential equations. An analytic solution of the problem has been found using a technique called homotopy analysis method (HAM). HAM gives consistently valid answers to the problem over an extensive variety of parameters and also provides better accuracy. To validate the analytical results, a comparison has been presented with a numerical solution calculated by using the parallel shooting method. The effects of dimensionless parameters, that is, deformation parameter, Reynolds number, Soret and Dufour numbers, and heat source/sink parameter on the expressions of velocity, temperature, and concentration profiles are analyzed graphically to understand the physics of the deformable channel. It has been noted that the velocity across the channel is higher for the expanding channel, as compared to that for the contracting channel. Also the Soret and Dufour number increases the temperature of the fluid, and decreases the concentration. The temperature profile has an increasing behavior in the case of heat source, and a decreasing behavior in the case of heat sink.     

Effects of SiC content on the densification,microstructure, and mechanical properties of HfB2–SiC composites

To investigate the effects of SiC on microstructure, hardness, and fracture toughness, 0, 10, 20, and 30 vol% SiC were added to HfB₂ and sintered by SPS. Upon adding SiC to 30 vol%, relative density increased about 4%; but HfB₂ grain growth had a minimum at 20 vol% SiC. This may be due to grain boundary silicate glass, responsible for surface oxide wash out, enriched in SiO₂ with higher fraction of SiC. By SiO₂ enrichment, the glass viscosity increased and higher HfO₂ remained unsolved which subsequently lead to higher grain growth. Hardness has increased from about 13 to 15 GPa by SiC introduction with no sensible variation with SiC increase. Residual stress measurements by Rietveld method indicated high levels of tensile residual stresses in the HfB₂ Matrix. Despite the peak residual stress value at 20 vol% SiC, fracture toughness of this sample was the highest (6.43 MPa m^0.5) which implied that fracture toughness is mainly a grain size function. Tracking crack trajectory showed a mainly trans-granular fracture, but grain boundaries imposed a partial deflection on the crack pathway. SiC had a higher percentage in fracture surface images than the cross-section which implied a weak crack deflection.