Fe3O4/PSt/TiO2多层包覆电磁响应微球的制备

首先采用分散聚合法将自制的Fe3O4磁流体和苯乙烯反应合成有磁核的Fe3O4/PSt磁性聚合物微球，然后，用非均匀成核水解反应在Fe3O4/PSt微球外包覆无定形二氧化钛，获得Fe3O4/PSt/TiO2复合微粒。用红外光谱、扫描电镜和热分析对粒子的形貌和结构进行了表征。并测试了微粒的介电性能和磁性，结果表明，所制得复合微粒有良好的电、磁响应性。     

Range of the Applicability of the Wilkins Method to the Investigation of the Dynamic Stress-Strain State of Anisotropic Elastic Axisymmetric Shells

The exactness and stability of the Wilkins method in the investigation of the stress-strain state of axisymmetric anisotropic elastic shells, including thick-walled ones, have been studied for different values of artificial viscosity, pulse load rise and fall time, and different deformation process durations. A comparison of numerical calculations, performed by means of an application software package developed by V. A. Romashchenko on the basis of the Wilkins method, with experimental results, known numerical data, and with calculations using the computation kernel LS-DYNA 3D has been carried out.     

用于高频谐振器的PbTiO_3基压电陶瓷

传统的PZT压电陶瓷的相对介电常数较大,一般为1 000以上,用于高频谐振器不易与线路匹配;而PbTiO3基压电陶瓷的相对介电常数较小,一般仅为200左右,对于10 MHz以上频率的谐振器,用PbTiO3基压电陶瓷作为压电振子是最佳的选择。本文主要研究用于高频谐振器的MnO2和Nd2O3改性PbTiO3基压电陶瓷的性质。PbTiO3基压电陶瓷的性质的改善是与此种陶瓷的制备工艺,显微结构和电导机制紧密相关的。     

防垢剂BZF－2的研制与应用

桩西油田产出原油综合含水已达６０％－７０％，原用防垢剂ＨＥＤＰ已失去有效抑制集输站结垢的性能。本工作针对结垢最严重的桩５２站的应用，研制了以有机膦化合物和聚氧乙烯醚为主成份的防垢剂ＢＺＦ－２，在室内考察了不同条件下的防垢率、腐蚀性、配伍性等性能，在桩５２站进行了为期４个月的现场试验，加量为１０．３ｍｌ／ｌ、防垢率≥９８．０％，加药设备管线的腐蚀率大大降低。     

烧结工艺对液相合成（SrPb）TiO3基陶瓷热敏特性影响的研究

本文在液相合成（ＳｒＰｂ）ＴｉＯ３粉的基础上，研究了升温速率、保温时间、烧结温度及降温方式对（ＳｒＰｂ）ＴｉＯ３基陶瓷的Ｖ型ＰＴＣ热敏特性的影响。实验表明：升温速率对其热敏特性影响不大，保温时间和烧结温度的作用是一致的，具有一最佳范围。而降浊方式对材料的热敏特性影响较大。综合各因素的影响，本配方中，样品的烧结制度定为：以２００℃／ｈ的速率升温，在１２５０℃保温１ｈ，炉冷至９５０℃，保温０．５ｈ，再     

中国古典园林三维造型研究

论述了采用层次结构化及参数化三维造型方法，建立一个以造型函数库为核心，从而构造各类、各级园林景观构件表面模型的方法和过程。对于某些非建筑类的园林配景构件，采用了Ｆｒａｃｔａｌ方法进行造型。     

Processing and microstructure of non-oxide ceramic fibres

Research and development efforts on high-temperature, oxidation-resistant fibres have increased over the past decade due to the demand for light-weight, stiff and strong composite materials in aerospace applications. Varieties of ‘high-performance’, continuous, non-oxide fibres with low-density, high tensile strength and tensile modulus have been developed either from organic precursors or via chemical vapour deposition for fabrication of ceramic matrix composites. Fibres derived from polymer precursors (e.g. Nicalon, Tyranno, HPZ) are small in diameter (compared to CVD monofilaments) and are ideally suited for ceramic composites. Processing, microstructural stability and mechanical properties of these newly developed SiC and Si₃N₄ base fibres are briefly reviewed in this paper.     

Microstructure-Property Correlation in AI_4C_3 Dispersion Strengthened Al Composite

The microstructure and tensile properties of Al_4C_3 dispersion strengthened Al composite fabricatedby reaction milling technique were investigated.It is indicated that the rod-like Al_4C_3 dispersoidshaving a diameter of 0.02-0.03 μm and a length of 0.1-0.3μm are formed by reaction of C with Al,and uniformly distributed in the Al matrix.The interface between Al_4C_3 and Al is clean and theinterfacial bonding is good.The matrix consists of the subgrains which have the size of 0.3-0.4μm,and most of the Al_4C_3 dispersoids are distributed on the subgrain boundaries.The 11 vol.-%Al_4C_3/Al composite exhibits an UTS (ultimate tensile strength) of 400 MPa and anelongation-to-failure of 8.0%.     

超细Fe3O4粒子表面包覆酞菁钴性质研究

本文研究了合成载氧体的金属有机化学液相淀积法制造工艺，所得产物经ＴＥＭ、ＸＰＳ、Ｍｏｓｓ－ｂａｕｅｒ谱和Ｂ－Ｈ仪等手段，研究了它的结构和磁性能。实验表明，酞青钴以薄层形式包覆在Ｆｅ＿３Ｏ＿４的表面，封闭了Ｆｅ＿３Ｏ＿４的表面孔洞，稳定了Ｆｅ＿３Ｏ＿４的物相，增强了磁性能。