A CALPHAD-type Young's modulus database of Ti-rich Ti–Nb–Zr–Mo system

Accurate Young's modulus is the necessity for the design of biomedical Ti alloys. A combinatorial method of the diffusion couple, nanoindentation, electron probe microanalysis (EPMA), and CALculation of PHAse Diagrams (CALPHAD) techniques has been utilized to construct the Young's modulus database of Ti alloys with various compositions in the present work. Two groups of body-centered cubic (bcc) Ti–Nb–Zr–Mo quaternary diffusion couples annealed at 1273 K for 25 h were experimentally prepared. Subsequently, the composition-dependent mechanical properties in the wide compositional range of Ti-based alloys were obtained by using EPMA and nanoindentation probes. Finally, on the basis of the measured Young's moduli in the present and previous work and the modeling parameters of Young's modulus of Ti–Nb–Zr system, the Young's modulus database of bcc Ti–Nb–Zr–Mo system was established through the CALPHAD approach. The CALPHAD-type database of bcc Ti–Nb–Zr–Mo system can provide the accurate Young's moduli of Ti alloys with wide compositions.     

Site occupations and ordering behaviour of O phase in Ti2AlNb—based intermetallics

1　ＩＮＴＲＯＤＵＣＴＩＯＮＴｈｅｏｒｔｈｏｒｈｏｍｂｉｃａｌｌｏｙｓａｒｅｏｆｇｒｅａｔｔｅｃｈ ｎｏｌｏｇ ｉｃａｌｉｎｔｅｒｅｓｔｉｎｈｉｇｈｔｅｍｐｅｒａｔｕｒｅａｐｐｌｉｃａｔｉｏｎｓｓｉｎｃｅｔｈｅｙｈａｖｅａｇｏｏｄｂａｌａｎｃｅａｍｏｎｇｓｔ     

The generation of surface roughness during slurry erosion-corrosion and its effect on the pitting potential

Results of experiments performed to isolate the effect of surface roughness generated during slurry erosion-corrosion of 304L stainless steel are presented. Surfaces prepared by grinding to different finishes show that increasing the roughness lowers the pitting potential in chloride solution. Subsequent erosion by an aqueous sand slurry then alters this pitting potential (E_p), as measured in the solution phase alone, in a manner dependent on the initial surface roughness. Surfaces which were initially rougher show a pronounced rise in _p after erosion, while those with an initially smoother finish show a fall in E_p after erosion. Measurement of E_p during erosion-corrosion does not fit either process, with values of _Ep lower than those predicted from the surface roughness alone.     

碳纳米管及稀土元素钇(Y)对高Ni含量Ti(C,N)基金属陶瓷组织与性能的影响

研究了不同含量的碳纳米管及0.8%稀土Y对高Ni含量Ti(C,N)基金属陶瓷组织性能的影响.将不同成分的试样分别于1400℃、1410 ℃、1420℃真空烧结,测试抗弯强度、洛氏硬度,观察背散射电子形貌、断口形貌并做能谱分析.结果表明,加入质量分数(下同)为0.8%Y及0.3%～1.0%的碳纳米管时,碳纳米管含量为0.5%的组织较均匀,芯壳结构明显,抗弯强度及硬度均较高.     

Analysis of Intermetallic Phases Formed on Surface Vapor Oxidized H13 Hot Work Steels in Molten Aluminum

In this paper, the author dipped surface vapor oxidized H13 steel specimens into 700℃ molten aluminum liquid for a certain period of time. Analyze the intermetallic phases formed on the H13 samples surface with optical microscope and X-ray diffraction method. The observation of immersion test sample's cross-section shows that Fe3O4 film will protect die substrate from molten aluminum erosion. The identification of the intermetallic phases reveals that they consist of 2parts, which is named as the composite layer and the compact layer. Further investigations are made in order to know the phase constituents of the 2 layers, they are Al8Fe2Si (outer composite layer), (AlCuMg) and Al5Fe2 (compact layer),respectively. The experimental results show that on the same specimen, a convex surface with bigger radius of curvature is more likely to be molten and the melting loss speed is also faster than a flat and smooth surface. The thickness of compact layer on a smooth surface is much bigger than that of the convex surface. Therefore, the author supposes the compact layer is favorable in stabilizing the die surface material from further melting loss, as their formation on the die surface, the melting loss speed will decrease.     

High resolution XPS characterization of chemical functionalised MWCNTs and SWCNTs

High resolution XPS analysis of chemical functionalised multi-wall carbon nanotubes (MWCNTs) and single wall carbon nanotubes (SWCNT) was done with ESCA300 (overall instrument resolution of 0.35 eV). Information to the degree of functionalisation was ascertained by argon ion bombardment of the samples followed by XPS analysis to detect the functional groups, the percentage atomic concentration of various elements present and whether or not the detected functional groups imposed a chemical shift on the CNT atoms. The results show that true chemical functionalisation was achieved and by argon ion bombardment these functional groups can be altered relative to the C 1s carbon atoms of the CNT. The choice of chemicals used for functionalisation, the techniques employed and the types of nanotubes treated are important factors in chemical characterisation. The carbon atom on the nanotube ring to which the functional group (atom) is bonded, the chirality of the CNT, the electronegativity of the functional group, the bond type and whether the CNT is single-wall or multi-wall, or cut (short) could play a role in determining the chemical shift on the CNTs atoms. These investigations are relevant to chemical functionalisation of carbon nanotubes for various applications for example DNA sensors and other biomedical sensors.     

Etude electrochimique de differentes ilmenites

The electrochemical behaviour of several natural ilmenites has been studied by cyclic voltammetry. From the analysis of the current-voltage curves it was concluded that the valences of the metal ions in FeTiO₃ are Fe^II and Ti^IV. It was also found that little amounts of Fe^III and excess of Ti^IV (probably TiO₂) can enter into the composition of the ilmenites.     

Carbonaceous adsorbents from sewage sludge and their application in a combined activated sludge-powdered activated carbon (AS-PAC) treatment

In this study, waste biological sludge is converted to an adsorbent by chemical activation with sulphuric acid. The adsorbent obtained is then applied to the aerated vessel of an activated sludge process treating glucose and phenol to improve the quality of the treated effluent. The sludge-based carbonaceous adsorbent was found to be mesoporous in nature, with a good adsorption capacity for large molecular weight compounds and limited removal efficiency for smaller molecules such as phenol. The addition of carbon, either sludge-based or commercial, enhanced phenol removal from 58% to 98.7% and from 87% to 93% the organic matter removal as measured by the chemical oxygen demand (COD) when operated with feed concentrations of 100 mg phenol/l and 2500 mg COD/l. No differences were found between the activated sludge-activated carbon bench scale continuous reactors operating with either commercial or sludge-based adsorbents in spite of the higher adsorption capacity of the former. It is suggested that powdered adsorbent bioregeneration in the combined AS-PAC system may be impaired by the obstruction of pores due to bacterial growth, the effect being more important for the commercial activated carbon with a narrower pore size distribution.     

Flakes of natural carbyne in a diamond mine

Flakes of natural carbyne were found in Liao-Ning diamond mine, China, and examined by HRTEM, XRD and EDX. Lattice fringes and clear SAD patterns were obtained. The interlayer spacings obtained with SAD were in good agreement with those determined on the powders found in Ries crater meteorite by X-ray diffraction. However, they are different in color and shape, the one found in China being black and flaky, but the one in Ries crater meteorite being silver-white and particulate. It was assumed that carbyne might be stabilized by the intercalation of either Si or Fe in nature.     

A203型低温氨合成催化剂使用小结

对Ａ２０３型低温氨合成催化剂的使用进行总结，介绍了该催化剂的装填，升温还原情况及使用效果。