机械合金化Fe50Ti50非晶的形成及球磨强度对它的影响

本文通过电子扫描和Ｘ衍射对机械合金人Ｆｅ５０Ｔｉ５０非晶粉末形成做了研究。研究发现：机械合金非晶形成可以大致地分为二个阶段－粉末的破碎阶段和非晶的形成阶段。另外，对球磨强度对非晶形成的影响进行了研究。结果表明：强度低时粉末需要较长的时间才能形成非晶，强度高时粉末形成非晶的时间大大缩短，但在随后的球磨中，粉末会重新晶化形成新相。     

用过滤工艺全面提高铸锭质量

探讨了过滤器孔径对6063铝合金铸锭组织和性能的影响规律。在此基础上指出,在过滤工艺恰当时,不仅可以减少铸锭中的夹杂物,而且可以有效地防止裂纹、羽毛晶等连续铸锭中的常见缺陷。     

Immobilization of inert TRISO-coated fuel in glass for geological disposal

Vitrification of TRISO-coated gas reactor fuel particles was achieved via two methods: glass melting and sintering. Inert TRISO-coated fuel particles and a borosilicate glass were used. With glass melting at 1200-1300 °C floatation and decomposition of carbon and silicon carbide occurred. Thermal pre-treatment of the particles for oxidation of pyrocarbon did not improve the coating properties of the glass. During cooling most of the particles floated and sorbed on the crucible or mold walls. The sintered glass at 700 °C showed better coating properties of the TRISO-coated fuel particles despite higher porosity compared to glass made by melting. Aqueous leaching properties of glass with particles are similar regardless the mode of fabrication, indicating the good chemical durability of the sintered glass. Sintered glasses may constitute a good technique for TRISO-coated fuel particles immobilization for an eventual deep geological disposal.     

米塔尔钢铁集团的全球并购发展战略

概述了米塔尔的并购经过和并购特点,着重探讨了米塔尔的管理模式、人员情况、钢铁厂布局、生产经营、主要战略伙伴、研发机构及其生产、采购与销售策略。系统地分析了米塔尔在中国的发展,指出米塔尔在全球钢铁业整合中处于领先地位,米塔尔来中国投资看中的是中国的原料和市场,且运作步伐明显加快,会对中国钢铁企业构成很大的威胁。     

Corrosion protection of iron by polypyrrole coatings electrosynthesised from a surfactant solution

This work is a study of the electropolymerisation of pyrrole onto iron electrodes in the presence of sodium bis(2-ethylhexyl) sulfosuccinate in a wide pH interval. The characterisation of the films was done using electrochemical techniques, SEM/EDX and IR spectroscopy. We show that it is possible to synthesise homogeneous, adherent and very compact films in the pH range between 7 and 12 under potentiodynamic, galvanostatic and potentiostatic conditions without substrate dissolution. The effects of various parameters on electrodeposition were investigated. The new procedure for the electrochemical synthesis of polypyrrole results in improved anticorrosion properties. The inhibition is proposed to be due to the sum of a repulsion of chloride ions because AOT remains entrapped in the polymer matrix and the presence of the iron oxide. Advantages of the use of surfactants in the electropolymerisation solution are discussed.     

Effect of cationic surfactant and inorganic anions on the electrochemical behavior of carbon steel in formation water

Corrosion behavior of carbon steel in formation water associated crude oil from Egyptian western desert was studied at various concentrations of dodecyl dimethyl ammonium chloride (CS) as a cationic surfactant. Polarization curves indicate that CS has a good inhibition efficiency for carbon steel in formation water and behaves as cathodic inhibitor. The inhibition efficiency was found to increase with increase in CS concentration until reaches a maximum constant value corresponding to the critical micelle concentration of CS and decrease with increase in solution temperature. The adsorption of CS follows the kinetic thermodynamic model and Flory-Huggins isotherm. Thermodynamic parameters obtained indicate that that the presence of the CS increases the activation energy. Polarization and Impedance measurements indicate that the addition of KI has a significant synergistic effect with CS and results in increase the inhibition efficiency of CS in formation water.     

Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

降低氧化铝生产中熟料折合比的探讨

在氧化铝生产过程中，熟料折合比是烧结法一项重要的综合性指标，本文通过对熟料折合比的定义、计算公式的剖析，分析了生产过程中影响熟料折合比的主要因素，对有效降低熟料折合比的措施进行了探讨。     

Pressure infiltration of boron nitride preforms with molten aluminum

The infiltration of compacted cubic BN (cBN) with molten aluminum has been investigated as a potential route for a cheap and easy method of manufacturing cBN/metal composites. CBN compacts have been infiltrated with molten Al at a temperature between 670 and 800 °C and pressure of 15 MPa in vacuum. At these temperatures no pronounced interactions between hexagonal and cubic BN with Al was observed, allowing the complete infiltration of cBN with 12 μm mean grain size. After infiltration at 800 °C, the temperature was increased without pressure to convert aluminum into borides and AlN. The hardness of the resulting materials depends on the content of hexagonal, cubic BN and the rate of conversion of Al into borides and AlN. The infiltration height of less than 1 mm obtained from infiltrating the 3 μm cBN powder green compacts gave a hardness of 22.0 ± 0.6 GPa after heat treatment.