Direct preparation of particles from liquid suspension for ESEM or SEM analysis

A simplified method for the preparation of particles from liquid suspensions has been developed. Particles are deposited directly on carbon planchets for rapid analysis by environmental scanning electron microscopy or by conventional scanning electron microscopy after an additional drying step. This is accomplished by filtering the liquid through thin carbon planchets. Three different grades of graphite were investigated for their suitability as the source material for these planchets. The high quality isomolded graphite is recommended for the filtration and direct observation of particles by electron microscopy. This technique is demonstrated for particles in hydraulic fluid and aquatic suspended particulate material from a natural water source.     

有机盐聚合醇氯化钾钻井液的应用

霍尔果斯背斜构造极其复杂,内应力极高,地层倾角大,断层、破碎带多,并存在高低压互层;安集海河组的灰绿色软泥岩水化严重并具有粘弹塑性.该区块重点探井霍003井三开、四开井段选用有机盐聚合醇氯化钾钻井液,同时为保证钻井液在高密度下（2.55 g/cm^3）具有好的流变性,使用活化铁矿粉、活化重晶石加重.应用结果表明,由于采用了强抑制和多元封堵的措施,该钻井液具有良好的流变性和较强的携带能力,钻进中曾携带出重2.8 kg和5.1kg的大掉块;滤失量低,泥饼质量好,封堵能力强,造壁能力强,减轻了井下阻卡程度;有良好的储层保护能力;在室内研究的基础上,经过现场合理使用和维护钻井液,霍003井提高了机械钻速,缩短了钻井周期,井身质量优于邻井.指出在高密度下,未选出适合有机盐聚合醇氯化钾钻井液的稀释剂,钻井液流动性较差.     

Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

Optimal production-inventory policy for make-to-order versus make-to-stock based on the M/Er/1 queuing model

This paper analyzes a multi-product production / inventory system where demands for each item arrive according to a Poisson process and the production time for each product has an Erlang distribution. The paper proposes an optimality condition that specifies whether each product should be produced make-to-stock or make-to-order. In the event a product should be produced make-to-stock, an approach for computing the optimal base-stock level is proposed. Numerical examples are given for illustrative purpose.     

LM2717型双降压直流/直流变换器的原理及其应用设计

LM2717是美国国家半导体公司推出的一款全新的高性能变换器,内含两个脉宽调制(PWM)直流/直流转换器,功能强大.介绍了该器件的主要参数、工作原理和引脚功能,讨论利用LM2717进行应用设计时选择外部器件的原则及设计中应注意的问题.     

Design and Manufacture of GeSi/Si Superlattice Nanocrystalline Photodetector

According to Maxwell＇s theory, the optical transmission characteristics in GeSi/Si superlattice nanocrystalline layer have been analyzed and calculated. The calculated result shows that when the total thickness L is 340 nm, the single mode lightwave can be transmitted only at periodic number M≥15.5. In addition, at the direction of transmission, when the transmission distance is larger than 500 μm, the lightwave intensity is decreased greatly. Based on the above parameters, the design and manufacture of GeSi/Si superlattice nanocrystalline photodetector are carried out.     

Measurement of the Metal Surface Acidity/Electronegativity of Pt(110)

In previous work, it has been found that a hydrogen-covered Pt(110) surface is acidic, but quantification of the acidity has not yet been done. In this paper a spectroscopic method is developed to measure the acidity of a metal surface for the first time. The technique involves measuring the intensity of the N–H stretch from the C₅H₄XNH⁺ that forms when hydrogen coadsorbs with pyridine, 2-fluoropyridine and 3-fluoropyridine. The Bethe approximation is then used to estimate the metal surface acidity/electronegativity (MSAEL). The proton affinity/MSAEL of Pt(110) has been determined to be 907 ± 4 kJ/mol at high coverage. This is the first time the MSAEL has been measured on a metal surface. Implications for fuel cell catalysis are discussed.     

Heat transfer enhancement by Marangoni convection in the NH3–H2O absorption process

The objectives of this paper are to quantify the effect of Marangini convection on the absorption performance for the ammonia–water absorption process, and to visualize Marangoni convection that is induced by adding a heat transfer additive, n-octanol. A real-time single-wavelength holographic interferometer is used for the visualization using a He–Ne gas laser. The interface temperature is always the highest due to the absorption heat release near the interface. It was found that the thermal boundary layer (TBL) increased faster than the diffusion boundary layer (DBL), and the DBL thickness increased by adding the heat transfer additive. At 5 s after absorption started, the DBL thickness for 5 mass% NH₃ without and with the heat transfer additive was 3.0 and 4.5 mm, respectively. Marangoni convection was observed near the interface only in the cases with heat transfer additive. The Marangoni convection was very strong just after the absorption started and it weakened as time elapsed. It was concluded that the absorption performance could be improved by increasing the absorption driving potential (x_vb−x_vi) and by increasing the heat transfer additive concentration. The absorption heat transfer was enhanced as high as 3.0–4.6 times by adding the heat transfer additive that generated Marangoni convection.     

用于微波/射频集成电路的一种新型低损耗介质——多孔硅及氧化多孔硅厚膜

提出在单片微波集成电路(MMIC)中用多孔硅/氧化多孔硅厚膜作微波无源器件的低损耗介质膜.研究了厚度为70μm的多孔硅/氧化多孔硅厚膜在低阻硅衬底上的形成,这层厚膜增加了衬底的电阻率,减少了微波的有效介质损耗.通过测量在低阻硅衬底上形成的氧化多孔硅厚膜上的共平面波导的微波特性,证明了在低阻硅衬底上用厚膜氧化多孔硅可以提高共平面传输线(CPW)的微波特性.