双洞口配筋砌块砌体框支墙梁试验

为研究双洞口配筋砌块砌体框支墙梁地震前后的受力模式,在拟动力子试验前后进行了底层框架配筋砌块短肢砌体剪力墙结构三层足尺模型的竖向力静载试验.试验结果表明:托梁与上部墙体表现出良好的协同工作能力,其工作模式为拉杆拱.通过对其在拟动力试验前后的受力模式进行了比较,可知带洞口配筋砌块砌体框支墙梁结构体系在墙体受到一定损伤时,并不会使墙梁的受力机理发生明显改变.     

导电涂料的研制

为了获得性能优良的导电涂料 ,采用对比试验和正交试验的方法对导电涂料进行了研究 ,分别对导电涂料的电阻、硬度、耐冲击强度、柔韧性等性能进行了测试 ,经过试验 ,确定了无机导电涂料的最佳配方为 :石墨 10 0g ,铅酸钡 10g ,三氧化二锑 5g ,二氧化钛 35g ,碳化硅 10g ,硅酸盐溶胶 170g。以此配方研制出了一种成本较低、生产工艺简单、具有良好的导电、导热性能的无机导电涂料。     

基于无线通信方式的TV二次压降现场测试方法

针对传统的TV二次压降现场测试方法存在的问题,提出基于无线通信技术的检测方法。以提高工作效率,降低安全风险。     

电控柴油机分缸均衡控制算法及试验

柴油机各个气缸的进气量、喷油量、燃烧等存在差异,导致气缸间存在做功差异,直接影响柴油机转速的平稳性以及排放性能等。针对位置式电控柴油机,采用PI闭环控制,通过瞬时转速信号识别并计算各缸的工作差异,利用分缸均衡控制算法对油量进行补偿修正。试验结果显示低转速稳态工况转速波动由7 r/min降至3 r/min,各缸工作不均匀度由±5 r/min降至±2 r/min,在瞬态过程和高转速3 400 r/min时该算法仍然适用有效。     

一维炉系统的测试实验

一维炉是一种研究煤的热解燃烧和结渣等方面的实验系统,可用于模拟电厂煤粉的燃烧特性。以元宝山褐煤为燃料,介绍了一维炉的结构和功能,并对系统的可靠性进行了验证,利用烟气分析仪及热重分析仪对燃烧后的尾部烟气及灰渣进行了分析测定。结果表明:尾部烟气含氧量与灰渣可燃部分剩余量均在理论计算值的误差允许范围内,说明一维炉密封良好,系统内各部分正常运行,对维炉的调试和研究具有一定的参考意义。     

Dynamic buffering performance of the honeycomb paperboard filled with polyurethane

A new kind of composite buffering material was made by filling the voids of honeycomb paperboard with polyurethane. Drop tests were performed to evaluate the dynamic energy absorption capacity of the material. Based on the tests results, we analyzed the mechanical behaviors of the material under different conditions and obtained the inherent influencing laws of some factors on the material＇s dynamic buffering performance. It was shown that the dynamic buffering performance varied directly with impact velocity, and inversely with the void diameter, thickness and buffeting area of the composite material.     

复杂系统平均寿命的估计和性质

根据已知的基于最小路径或最小割集复杂系统可靠度函数的解析表达式,给出当子系统寿命分布服从指数分布时,系统平均寿命的表达式.利用这一表达形式,在子系统寿命变量服从指数分布条件下,分别就完全数据和截尾数据两种情况,给出了系统平均寿命的估计,并对估计性质进行了研究.并在完全数据下,给出了估计的渐近分布.     

我国宏观经济与证券市场关系的实证分析--基于名义 GDP 和上证指数发展速度的视角

宏观经济和证券市场的关系一直受到人们的关注,由于数据的选取和研究方法上的不同,导致宏观经济与证券市场的关系存在不同的结论或解释。从名义 GDP 和上证指数发展速度的视角,运用 HP 滤波以及 SVAR 等方法实证研究了宏观经济和证券市场的关系。研究发现：宏观经济和证券市场存在显著的因果关系;短期证券市场的波动是经济偶然性波动的预期,两者之间的滞后期效应与当期效应相互影响;方差分解表明宏观经济对于证券市场的长期贡献度很大。     

Effect of surface coating on the screw loosening of dental abutment screws

Regardless of the type of performed restoration, in most cases, a screw connection is employed between the abutment and implant. For this reason, implant screw loosening has remained a problem in restorative practices. The purpose of this study was to compare the surface of coated/plated screws with titanium and gold alloy screws and to evaluate the physical properties of coated/plated material after scratch tests via FE-SEM (field emission scanning electron microscopy) investigation. GoldTite, titanium screws provided by 3i (Implant Innovation, USA) and TorqTite, titanium screws by Steri-Oss (Nobel Biocare, USA) and gold screws and titanium screws by AVANA (Osstem Implant, Korea) were selected for this study. The surface, crest, and root of the abutment screws were observed by FE-SEM. A micro-diamond needle was also prepared for the scratch test. Each abutment screw was fixed, and a scratch on the surface of the head region was made at constant load and thereafter the fine trace was observed with FE-SEM. The surface of GoldTite was smoother than that of other screws and it also had abundant ductility and malleability compared with titanium and gold screws. The scratch tests also revealed that teflon particles were exfoliated easily in the screw coated with teflon. The titanium screw had rough surface and low ductility. The clinical use of gold-plated screws is recommended as a means of preventing screw loosening.     

橡胶冲裁模具刃口间隙的探讨与研究

阐述了合理选择丁基橡胶瓶塞冲裁模具的刃口间隙是提高模具使用寿命的关键，介绍了模具刃口间隙的确定方法。