二阶曲线渐近线的等价定义及其应用

给出了射影几何中关于二阶曲线渐近线的几个等价定义,并探讨了根据不同 定义的二阶曲线渐近线的应用．     

Experimental and analytical study on the spray characteristics of dimethyl ether (DME) and diesel fuels within a common-rail injection system in a diesel engine

This paper investigates the effect of injection parameters on the characteristics of dimethyl ether (DME) as an alternative fuel in a diesel engine with experimental and analytical models based on empirical equations. In order to study macroscopic and microscopic characteristics of DME fuel, this work focuses on the atomization characteristics of DME and compares experimental and predicted results for spray development obtained by empirical models for diesel and DME fuel. Detailed comparisons of spray tip penetration from three different empirical correlations and from visualization experiments of diesel and DME fuels were conducted under various fuel injection conditions. In comparison with the results of different empirical equations for measured spray tip penetration, the experimental results of this study provide good agreement with the calculation results based on empirical equations, except during the earliest stage of the injected spray sequence. The results of atomization characteristics indicate that DME showed better spray characteristics than conventional diesel fuel. Also, the fuel injection delay and maximum injection rate of DME fuel are shorter and lower than those of diesel fuel at the same injection conditions, respectively.     

Synthesis of polyurethane resins and its improvement on dimensional stability and finishing performances of medium‐ and small‐diameter softwoods

This study analyzed the effects of polyurethane (PU) resin treatments on surface homogeneity, dimensional stability, and finishing performances of medium‐ and small‐diameter softwoods produced in Taiwan. Two‐pack PU resins were prepared by combing short castor oil‐modified alkyd resin serving as a polyol with polymeric 4,4′‐diphenymethane diisocyanate (PMDI) serving as a hardener, by the molar ratio of NCO/OH+COOH of 1.2. Four types of short oil‐modified alkyd resins with different polyhydric alcohols (glycerin and pentaerythritol) and polybasic acids (phthalic anhydride and isophthalic acid) were synthesized. Three kinds of medium‐ and small‐diameter softwoods, including China fir, Taiwanina, and Japanese fir with a diameter of 10–15 cm were obtained from Hui‐Sun Forest Station, Taiwan. The wood coating of nitrocellulose (NC) lacquer including sanding sealer and top clear was used. Results show that the surface hardness, homogeneity, moisture excluding efficiency, and antiswelling efficiency of woods were enhanced by PU resin treatments. Among all the PU resins, the isophthalic acid and pentaerythritol‐containing PU resin (IPA‐P‐MDI) achieved the best improved efficiency on dimensional stability of woods. Results of two types of finishing procedure, i.e. NC lacquer sanding sealer plus top clear and top clear only, applied onto the PU‐treated woods revealed that the hardness, adhesion, and durability of NC lacquer films on the PU‐treated wood were superior to those of untreated one, especially for top clear finishing alone. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

蒸发冷凝法中气体压强和蒸发温度对粒子大小的影响

在Ｎ＿２气氛中，用蒸发冷凝法，制备了Ｓｎ细微粒和Ｆｅ及Ｆｅ－４７（ｗｔ）％Ｎｉ合金超细微粒。分别用ＳＥＭ和ＴＥＭ，直接观测粒子大小及其分布。结果表明，平均粒径不是随Ｎ＿２气压强增加单调上升，而是在某一压强Ｐ＿（ｍａｘ）下，出现最大值。随蒸发温度提高，Ｐ＿（ｍａｘ）值迅速增大。粒子大小及其分布与粒子生长机制密切相关。对粒子凝聚生长条件进行了简要讨论。     

A graded diameter and oriented nanorod–thin film structure for solar cell application: a device proposal

This paper presents a device proposal based on a junction between an absorbing semiconductor nanorod structure and another window semiconductor layer for solar cell application. The possibility of band gap tuning by varying the diameter of the nanorods along the length, higher absorption coefficient at nanodimensions, the presence of a strong electrical field at the nanorod-window semiconductor nanojunctions and the carrier confinement in lateral direction are expected to result in enhanced absorption and collection efficiency in the proposed device. Process steps, feasibility, technological tasks needed for the realization of the proposed structure and the novelty of the present structure in comparison to the already reported nanostructured solar cells are also discussed.     

圆锥孔径测量方法与误差分析

圆锥孔径的测量往往比较困难、且精度较低。提出长度测量仪器与环规配合使用,应 用比较测量的方法检测圆锥孔的直径。通过计算和分析可以得出,当被测圆锥孔径不大于180 mm 时,其测量不确定度可小于1.84 μm。给出了测量方法和不确定度计算公式供操作时参考。     

钻井岩屑粒径分布规律的研究

钻井振动筛是固控系统的重要分离设备,其主要任务是清除钻井液中直径大于74μm的固相颗粒。对辽河油田7口井深0～3500m的钻井岩屑进行了实地取样,分析了岩样颗粒直径大于74μm的粒径分布特征。分析结果表明,钻井岩屑具有明显的片状特征,颗粒的粒径分布主要与地层岩性和破岩工具有关,随着井深的变化,其岩样粒径分布呈现出幂分布、2分布和瑞利分布等3组典型规律。给出了岩屑颗粒的概率直径;建议在筛面颗粒运动特性研究、筛网工作载荷的计算和激振方式的选择中,应考虑岩屑颗粒片状特性的影响。     

Calculated hardenability for improved consistency of properties in heat treatable engineering steels

Hardenability is one of the most important parameters controlling the heat treated properties of engineering steels. It affects the consistency of response for microstructure, hardness, strength, toughness, and dimensional change (distortion). This study illustrates that a major benefit of controlling hardenability is improving the consistency of dimensional distortion resulting from heat treatment. To facilitate the supply of steels to hardenability limits, especially restricted hardenability, a new technique was developed for the prediction of Jominy hardenability from chemical composition. The technique, termed the “Database Method,” uses measured Jominy hardenability and chemical composition data, contained in a database, to calculate the hardenability for a query composition. Using up to ten known steels, selected from the database with compositions closely matching that of the query steel, a small adjustment is made to the measured hardenability of each known steel allowing for the small difference in composition between the query and chosen steel. The final calculated result for the query steel is taken as the average of the various estimates. The basis of the Database Method is explained, and the advantages are illustrated for selecting engineering grades.     

钛制容器产品试板压弯角度的探讨

针对钛制容器产品试板弯曲角度按现行标准执行中出现的问题，从力学角度进行探讨，导了了试板压弯对所采用的压头直径与试板厚度和延伸率的关系，即Ｄ〉（１／δ－１）ｔ，并提出了设定试板弯曲压头直径的新思路。     

An improved light attenuation technique for measuring large interfacial areas

A laser-based light attenuation technique was successfully used to measure interfacial areas as high as 5832 m²/m³ and Sauter mean bubble diameter varying between 50 and 5600 μm. Good agreement between this approach and the photographic technique was obtained particularly at low gas holdups.