国产弧焊机器人在汽车车厢焊接生产线上的应用

本文对“TL-1”天龙一号国产弧焊机器人在汽车车厢前板总成焊接生产线上实际应用进行了分析,并对焊接对象的选取、工艺布置、夹具及夹具控制系统,机器人与夹具的循环系统,系统可靠性和抗干扰措施的诸方面进行了论述。     

TIG焊和PAW焊中活性剂对焊缝熔深的影响

针对常规TIG焊生产效率低、熔深小等问题，研究了TIG焊和PAW焊中应用活性剂对焊缝熔深的影响。结果表明，应用活性剂后，在同样的参数下，同传统TIG相比，活性剂能够大幅度提高不锈钢、铝合金和钛合金的焊缝熔深。对于PAW焊，熔深也有增加，但是增加的幅度不如TIG效果明显，但对焊缝成形有很好的改善。同时，活性剂对铝合金焊接背面能够起到保护作用。对于钛合金，活性剂除了增加焊缝的熔深外，还能够大幅度地消减焊缝产生的气孔。     

Microstructure of a nitrided steel previously decarburized

In this study the effects of a surface-controlled decarburization on the structure of a nitrided steel are analyzed. Samples of a quenched and tempered 42CrMo4 steel were decarburized by heating in air at different depths and submitted to gaseous nitriding. After decarburization and nitriding, the microstructure of surface layers was investigated by optical microscopy (OM) and scanning electron microscopy (SEM). The nitrogen and carbon profiles in the diffusion layers were determined by SEM equipped with a wavelength dispersive spectrometer (EPMA-WDS) and by glow discharge optical spectrometry (GDOS). The effect of nitriding was determined by microhardness measurements. Our results indicate that a previous decarburization only slightly affects the surface hardness, but reduces the conventional nitriding depth. The decarburization also favors the nitrogen take-up and produces increased nitrogen concentrations in the compound layer and in the narrow zone beneath it.     

电火花铣削中电极损耗及补偿的几何描述方法

提出了电火花铣削加工的基于数学模型的电极分解加工补偿法，即通过将电火花铣削加工过程划分为两个阶段——型腔侧面轮廓加工和底面的加工，这样就简化了放电状态的检测和电极补偿运动。在分别对侧面和底面加工过程分析的基础上，建立了侧面轮廓和底面加工的电极损耗和补偿的数学模型，为电极自动在线补偿提供了理论基础。     

基于RP原型的电弧喷涂快速模具制造技术研究

基于RP原型的电弧喷涂快速模具制造工艺是一项模具制造新技术。本文介绍了这种工艺的原理和方法。并重点讨论了该制模技术的关键。     

利用双层辉光放电形成Mo-N硬质镀层

用双层辉光放电在钛合金Ti6Al4V表面形成了Mo-N硬质镀层。用X射线衍射仪和纳米压入仪分别对镀层的相结构、硬度和弹性模量进行了研究，并用涂层压入仪对镀层与基体间的结合强度进行了测定。结果表明：Ti6Al4V表面形成了均匀的Mo—N硬质镀层，镀层厚约10μm，由面心立方结构Mo2N化合物构成；Mo2N硬质镀层的硬度和弹性模量分别为13．80GPa和261．65GPa;镀层与基体间具有较好的结合强度。     

The Microstructure and Mechanical Properties of the Low Carbon Microalloy Steel by High Voltage Electropulse Heating

The low carbon microalloy steel samples were heated to different temperatures by high voltage electropulse discharge heating method. The temperature of sample increases with the discharge current density. Microstructures were observed by using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Results show that coexist microstructure of ultrafine ferrite grain and martensite can be obtained by proper high voltage electropulse discharge heating process parameter. The tensile testing indicate that better mechanical properties were obtained, including 758MPa yield strength, 796MPa ultimate strength and 12% total elongation.     

钛合金表面双层辉光离子渗铝的研究

利用双层辉光渗金属技术，以铝为源极、TC4(Ti-6Al-4V)为阴极、氩气为工作气体，依靠辉光放电和不等电位空心阴极效应在TC4表面形成合金层。采用X射线衍射和辉光放电光谱分析了合金层的相组成及渗层内Al元素的分布．并对其进行硬度测试。结果表明：渗层由Ti3Al和α-Ti组成；铝的含量可达18％；渗层厚度可达13μm；其硬度比经渗铝处理后的有了较大程度的提高。     

Pt/onion-like fullerenes as catalyst for direct methanol fuel cell

Onion-like fullerenes synthesized by arc discharge in water were used as support of Pt nanoparticles as electrocatalytic materials for direct methanol fuel cell. Uniform platinum nanoparticles with the average diameter of about 4.3 nm were well dispersed on the surface of onion-like fullerenes by impregnation-reduction method. The morphologies and microstructures of the as-prepared composites were studied by means of XRD and TEM. Electrochemical analysis shows that this kind of nano material may be an excellent candidate to be used as the support of catalyst for methanol electrochemical oxidation.