连续驱动摩擦焊动态扭矩检测的新方法—VCMM法

连续驱动摩擦焊动态扭矩检测的新方法──ＶＣＭＭ法刘金合，罗键连续驱动摩擦焊扭矩是一个重要的工艺参数。摩擦焊扭矩是动态扭矩，具有时变性、速变性以及变化范围大等特点。现有的检测摩擦焊扭矩的方法均有一定的局限性’‘－’‘，本文提出了通过驱动主电机定子电压和...     

利用含钨废催化剂生产钨酸的工业实践

笔者较为详细地阐述了利用含钨废催化剂生产钨酸的工艺流程、各工序反应原理及其操作工艺实践、产品质量情况、原辅材料单耗等。实践证明 ,该工艺实用性强 ,具有显著的经济效益、社会和环保效益。     

省煤器管开裂原因分析

对省煤器开裂管进行了化学成分及宏、微观分析。分析结果表明，在高温高压条件下，在其焊缝溶合区出现粗大的魏氏组织，管材中的珠光体组织产生了不同程度的球化，而母材组织又存在严重的带状组织。在过热条件下熔合区极易出现裂纹，并由此快速扩展，造成省煤器管开裂。     

工业厂房48M抽柱工程施工工艺

以莱钢万力H型钢有限公司抽柱换梁工程为例，介绍行车梁拼装、柱加固拆除及托粱吊装前后的测量观测。     

Biaxiale Ermüdung reibrührgeschweißter Strukturelemente

Biaxial fatigue of friction stir welded stiffened panels Within the framework of the European WelAir project, cruciform specimens made from stiffening FSW overlap joints were fatigued in the DLR biaxial test rig. To resemble the loading situation of pressurized fuselage structures, proportional loading without any phase shift, but with different load ratios λ between the loading components in both directions was applied.Natural crack initiation and subsequent crack growth were governed by the stiffness gradient caused by introducing the stringer. Cracks initiated and propagated at run‐in and run‐out locations in a direction perpendicular to the weld seam. The shortest fatigue life was observed for uniaxial loading in welding direction (λ = 0). An additional stress component perpendicular to the joint line (λ > 0) resulted in a higher number of cycles to failure. Similar to single stringer panels, increasing the load ratio also increased the number of cycles to failure for FSW clip‐stringer structural members, but additionally gives a different location of the fatal crack.     

海洋平台双相不锈钢管线的焊接

就双相不锈钢的特异性能．介绍双相不锈钢管线的焊接特点与技术。     

Influence of Ni Interlayers on the Mechanical Properties of Ti6Al4V/(WC-Co) Friction Welds

Ni interlayers were introduced prior to dissimilar friction welding of Ti6Al4V base material to three cemented carbide substrates. The fracture strength of Ti6Al4V/(WC-6 wt% Co) welds were poor and were markedly improved when 20-µm thick Ni interlayers were introduced prior to dissimilar friction welding. These results were only produced when the (WC-6 wt% Co) cermet was electroplated prior to friction welding. When the Ti6Al4V alloy was electroplated prior to friction welding, fractured WC particles and cracking were observed in the (WC-Co) carbide substrate. The fracture strengths of Ti6Al4V/(WC-11 wt% Co) and Ti6Al4V/(WC-24 wt% Co) welds were not improved when 20-µm thick Ni interlayers were introduced prior to friction welding. During mechanical testing, the Ni layer retained at the dissimilar joint interface created a region of weakness.     

唐钢ER70S-6焊丝钢的生产工艺研究及质量分析

介绍了唐钢ER70S-6焊丝钢的特点，对盘条质量进行了分析。对该钢化学成分、冶炼和轧制工艺进行了优化研究，使其综合性能明显改善。     

钻机绞车滚筒体的窄间隙埋弧焊

针对钻机绞车滚筒体采用手工电弧焊工人劳动强度大、焊接效率低、质量不稳定及返修率高等问题,研制了钻机绞车滚筒体窄间隙埋弧焊专机。该专机由ESAB—A2埋弧焊电源和焊接小车、窄间隙焊头、滚轮架、防窜装置、旋转地线夹、三维焊接工作台、焊剂自动回收机组成。使用表明,采用该焊机焊接的滚筒体焊缝质量完全符合设计要求,合格率100%,焊接效率比原来提高6倍。每件滚筒体的焊接可降低人工成本约80%。     

爆炸焊接边界效应的力学能量原理

在爆炸焊接工艺中,存在一种称为边界效应的物理现象。即在一般情况下,在爆炸焊接后的复合材料中,会出现雷管区不复、其余周边被打伤、打裂和变形严重等问题。这些问题严重地影响着这类材料的质量。该文从传统的和经典的力学及能量原理出发,探讨了边界效应产生的力学 能量原理,并且提出了预防的措施。