Selective hydrogenolysis of glycerol to propylene glycol on Cu–ZnO catalysts

Hydrogenolysis of biomass-derived glycerol is an alternative route to sustainable production of propylene glycol. Cu–ZnO catalysts were prepared by coprecipitation with a range of Cu/Zn atomic ratio (0.6–2.0) and examined in glycerol hydrogenolysis to propylene glycol at 453–513 K and 4.2 MPa H₂. These catalysts possess acid and hydrogenation sites required for bifunctional glycerol reaction pathways, most likely involving glycerol dehydration to acetol and glycidol intermediates on acidic ZnO surfaces, and their subsequent hydrogenation on Cu surfaces. Glycerol hydrogenolysis conversions and selectivities depend on Cu and ZnO particle sizes. Smaller ZnO and Cu domains led to higher conversions and propylene glycol selectivities, respectively. A high propylene glycol selectivity (83.6%), with a 94.3% combined selectivity to propylene glycol and ethylene glycol (also a valuable product) was achieved at 22.5% glycerol conversion at 473 K on Cu–ZnO (Cu/Zn = 1.0) with relatively small Cu particles. Reaction temperature effects showed that optimal temperatures (e.g. 493 K) are required for high propylene glycol selectivities, probably as a result of optimized adsorption and transformation of the reaction intermediates on the catalyst surfaces. These preliminary results provide guidance for the synthesis of more efficient Cu–ZnO catalysts and for the optimization of reaction parameters for selective glycerol hydrogenolysis to produce propylene glycol.     

超高分子量聚乙烯纤维表面处理的研究进展

详细介绍了超高分子量聚乙烯纤维的各种表面处理方法 ,如等离子体处理、电晕放电和化学氧化等 ,重点讨论了这些方法对纤维增强复合材料粘结性能和力学性能的影响 ,特别关注了近年来各种表面处理超高分子量聚乙烯纤维技术的进展。     

选择性螯合滴定法测定电镀液中的锡铜铅

提出了测定电镀液中锡铜铅的一个简易快速螯合滴定法.用EDTA螯合锡(Ⅳ)、铜(Ⅱ)、铅(Ⅱ)和其它金属离子,然后分别用三羟基苯甲酸、巯基丁二酸和氨荒丙酸解蔽.释放出的EDTA,用锌标准溶液反滴定(XO-CPB为混合指示剂).终点变化相当敏锐.研究了测定锡、铜、铅时一般共存离子的干扰.此法已被成功地用于测定锡-铜-铅合金电镀液和镀层锡铜铅合金中的锡、铜和铅.     

Sorption of ethene and ethane on the V2O5(001)/TiO2(001) anatase interface

Simulation techniques have been employed to investigate the differences in the low energy adsorption configurations of ethene and ethane on the TiO₂ supported and unsupported V₂O₅(001) surface. We find that the ethene molecule approaches much closer to thesupported V₂O₅(001) surface which is reflected in the 40 kj mol^–1 higher adsorption energy. The low energy adsorption configuration located for ethane on the supported V₂O₅ shows that the molecule does not approach as close to the supported V₂O₅ surface as does ethene, resulting in the adsorption energy of ethane being 52 kJ mol^–1 lower than that of ethene on the supported V₂O₅ surface.     

Effect of the metal oxide loading on the activity of silica supported MoO3 and V2O5 catalysts in the selective partial oxidation of methane

Precipitated silica catalysts loaded with either MoO₃ (0.2–4.0 wt%) or V₂O₅ (0.2–5.3 wt%) have been studied in the selective partial oxidation of methane to formaldehyde with molecular oxygen at 520 °C. The functionality of the SiO₂ surface towards the formation of HCHO is significantly promoted by V₂O₅, while it is depressed by the MoO₃.     

A study about the effect of the temperature of hydrogen treatment on the properties of Ru/Al2O3 and Ru/C and their catalytic behavior during 1-heptyne semi-hydrogenation

The 1-heptyne selective hydrogenation carried out at 150 kPa, and at 283 and 303 K using Ru/Al₂O₃ and Ru/C as catalysts, was studied. Catalysts were prepared by the incipient wetness impregnation technique using RuCl₃ as precursor. Ru/Al₂O₃ was treated in hydrogen at 373 or 573 K and Ru/C only at the last temperature. Catalysts were characterized by hydrogen chemisorption, TPR and XPS. Ru dispersion after treatment in hydrogen at the highest temperature is similar for both catalysts. Ru is present as Ru⁰ in Ru/C, while Ru⁰ and Ru electron-deficient species are present on the catalysts surface after hydrogen treatment at the two temperatures using Al₂O₃ as support. The best catalytic behavior was observed for the highest temperature of hydrogen treatment and for 303 K reaction temperature. As a consequence of a shape selectivity effect of the C support, the best conversion is obtained with the alumina supported catalyst.     

红土镍矿干燥焙烧工艺条件选择研究

以红土镍矿为原料,用热重分析(TG)和X射线衍射分析(XRD)等方法,对红土铁矿干燥焙烧条件进行研究.结果表明,在矿石粒度为0~3 mm且小于180目颗粒占25%,配焦粉量8%,焙烧温度850℃,焙烧时间90 min,干燥焙烧效果最佳.     

案例知识库维护技术的研究进展

案例库是CBR系统的主要知识库,但是难以维护,一个主要因素是案例库大,并且是非结构化或半结构化的,用自然语言来表达的．文章针对案例知识库维护中出现的相关复杂问题,分析了各种维护策略的可行性,提出了在不同环境下实施维护的准则,指出了选用合适的方法来实现案例库维护．