建筑墙体表面传热系数辨识研究

对实验房间南向墙体内表面中心区域的换热过程进行实验，发现当风速在0－5．5m/s之间时，表面传热系数在8－18W（m^2.K）之间波动，而风向对墙体表面传热系数影响不大；用辅助变量法分析墙体表面传热过程，并结合实验推导出墙体表面传热系数。模型的预测结果与实测结果吻合良好。     

大长径比自旋弹箭横向自振特性的有限元计算方法与结果分析

本文研究大长径比自旋弹箭在飞行时横向振动的自振特性。本文将转子动力学应用于弹道学 ,采用有限元法 ,建立自旋弹箭横向振动自振特性方程。同时给出了计算方法。利用该方程和该方法 ,开发了相应的计算程序。通过数值计算 ,可给出细长旋转弹箭飞行时的进动转速和临界转速 ,以及相应的位移和角度振型。利用该程序 ,进行了实例计算和分析。     

复合形法优化内河航道重力式护岸

采用复合形优化法,结合《港口及航道护岸工程设计与施工规范》中推荐的抗滑、抗倾稳定的分项系数计算方法,并考虑了内河航道船形波等作用的影响效应,对重力式护岸断面进行了优化。     

燃烧—气体容量法测定冶金石灰中的二氧化碳

冶金石灰是石灰石经过工业煅烧的产品。其二氧化碳含量低，且经过高温煅烧后基本不含有机物。无需按照《石灰石、白云石化学分析国家标准中二氧化碳的化学分析方法》中用酸进行试样分解，只需在1200℃高温中灼烧，使石灰中残留的或煅烧后吸收空气中二氧化碳而形成的碳酸盐分解，象通常测定含碳耐火材料中二氧化碳那样，采用气体容量法进行测定。     

A continuum-based modeling of MEMS devices for estimating their resonant frequencies

A continuum-based modeling of coupled electrostatics-structure interactions is presented for the frequency computations of MEMS devices. The present general formulation of electrostatics accounting for free space is validated first by specializing it to one-dimensional uniform motion of conducting surfaces and comparing the resulting electrostatics to conventional lumped models. The general coupled electrostatics-structure interactions are then applied for the prediction of resonant frequencies of MEMS devices due to bias-voltage changes and temperature variations. Comparisons of predicted resonant frequencies obtained by the present coupled electrostatics-structure interaction models with experimental results available in the literature demonstrate that the proposed continuum-based interaction modeling yields high-confidence predictions of resonant frequencies of MEMS devices.     

Influence of accelerated ageing on methacrylate‐based denture resins heterogeneity as viewed by ESR‐spin‐probe method

The electron‐spin‐resonance (ESR) spin‐probe method, was used to study the heterogeneity of denture resins based on poly(methyl methacrylate). Results for three resins processed by microwave energy, conventional curing and cold curing (depending on the curing procedure and exposed to ageing in various environmental conditions) were compared. All three cured resins were stored over the same time (1200 h) in distilled water at ambient temperature and in artificial saliva at 348 K. The temperature‐dependent ESR spectra of a spin probe dispersed in the denture resins are analyzed in terms of line‐shapes and line‐widths. The appearance of two spectral components was taken as an indication of resin heterogeneity. The results reveal that the cold‐cured resin has a lower local density in comparison with microwave and conventionally cured resin. The amount of residual monomer also contributes to the local motion of polymer segments. The change of denture resins exposed to ageing is influenced both by the structure of the original resin and the ageing conditions. Restricted motion of a spin probe incorporated into the acrylic resins exposed to accelerated ageing suggests additional crosslinking of polymer chains. The differences are observed for all the investigated resins, but the highest change is observed with the cold‐cured resin. The ESR results are accompanied by T_g and T_m measurements. Copyright © 2005 Society of Chemical Industry     

Cholesterol‐imprinted polymer receptor prepared by a hybrid imprinting method

A novel cholesterol‐imprinted polymer (CMIP‐H) was prepared by a hybrid method of covalent imprinting and non‐covalent imprinting. This approach involves the copolymerization of a template‐containing monomer, cholesteryl 2‐hydroxyethyl methacrylate carbonate, and a cross‐linker, followed by hydrolysis to afford a flexible guest‐binding site accompanied with the easy and efficient removal of a ‘sacrificial spacer’. The effect of solvent on the binding capacity of CMIP‐H towards cholesterol was studied, indicating that a good binding capacity towards cholesterol could be achieved in a less‐polar solvent. The binding experiments of CMIP‐H towards a series of structural analogues of cholesterol, including cholesterol acetate, progesterone and stigmasterol, were carried out in hexane. The results showed that CMIP‐H almost did not bind cholesterol acetate at all because the hydrogen‐bonding site is blocked. It exhibited a similar binding towards both cholesterol and stigmasterol, but much higher binding towards progesterone. Copyright © 2005 Society of Chemical Industry     

A comparative study of numerical solutions to non-linear discrete crack modelling of concrete beams involving sharp snap-back

Numerical problems are often encountered in modelling crack propagation in concrete beams using non-linear finite element (FE) analysis, especially when sharp snap-back behaviour in load-displacement relations occurs. This paper firstly identifies 16 arc-length control based numerical strategies based on extensive literature review. They are then used to carefully model the structural behaviour of a four-point single notched shear beam using discrete crack modelling approach in which cracks are represented by interface elements with bilinear softening constitutive laws. Based on extensive FE analyses, detailed comparisons of the merits and demerits of these numerical algorithms are then made. The results indicate that the effectiveness and efficiency of different algorithms may vary considerably from one to another, with the local arc-length based procedures in conjunction with tangential stiffness strategy and reversible unloading model being the most robust.     

Visual evaluation at scale of threshold to suprathreshold color difference

Visual evaluation experiments of color discrimination threshold and suprathreshold color‐difference comparison were carried out using CRT colors based on the psychophysical methods of interleaved staircase and constant stimuli, respectively. A large set of experimental data was generated ranged from threshold to large suprathreshold color difference at the five CIE color centers. The visual data were analyzed in detail for every observer at each visual scale to show the effect of color‐difference magnitude on the observer precision. The chromaticity ellipses from this study were compared with four previous published data, of CRT colors by Cui and Luo, and of surface colors by RIT‐DuPont, Cheung and Rigg, and Guan and Luo, to report the reproducibility of this kind of experiment using CRT colors and the variations between CRT and surface data, respectively. The present threshold data were also compared against the different suprathreshold data to show the effect of color‐difference scales. The visual results were further used to test the three advance color‐difference formulae, CMC, CIE94, and CIEDE2000, together with the basic CIELAB equation. In their original forms or with optimized K_L values, the CIEDE2000 outperformed others, followed by CMC, and with the CIELAB and CIE94 the poorest for predicting the combined dataset of all color centers in the present study. © 2005 Wiley Periodicals, Inc. Col Res Appl, 30, 198–208, 2005; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/col.20106     

电容传感器在使用中存在的几个问题及处理方法

随着电容测量技术的迅速发展，电容传感器在非电量测量和自动检测中得到广泛应用，但它在使用过程中也存在一些问题，针对在使用电容传感器过程中存在的几个问题，从电容传感器的原理和工作过程两个方面进行了讨论，并提出行之有效的处理方法。