纳秒级上升时间的高压脉冲群电源

按照IEC 61000-4-4/GB 17626.4—1998的要求，首先应用PSPICE仿真确定电路中各元件的参数值，然后基于拉普拉斯变换用MATLAB求解二阶电路验证各元件参数。在此基础上研制了一台以开关电源作为高压直流电源、以氢闸流管作为主控开关的脉冲群电源。该电源体积小、重量轻、效率高、成本低廉。试验结果表明，其输出信号符合标准要求，可用于快速瞬变脉冲群抗扰度试验。     

铁电材料用于阴极发射的研究

铁电材料作为一种新型的阴极材料，具有真空要求低、制作简单、功函数低、响应速度快等特点。本文讨论了铁电阴极发射的机理，回顾了主要铁电阴极材料的发射实验，包括低电压铁电发射实验，最后对铁电阴极材料的应用做了讨论和展望。     

一种自动冲水控制装置的开发和应用

介绍光电被动感应控制开关模块工作原理，研究开发了一种基于被动感应控制原理的自动冲水控制装置，总结比较了主动感应控制与被动感应控制的优缺点及其应用特点。     

一种精密温度控制仪

采用精密温度补偿及在传统PID调节基础上运用模糊控制运算 ,实现以单片机为基础开发研制的精密温度控制仪 ,并输出时间开关量信号和 4～ 2 0mA标准电流信号 ,为闭环控制及温度值远传提供依据。     

Modeling and performance analysis of IP access interface in optical transmission networks with packet switching

The article analyzes the influence of the Internet Protocol (IP) access interface on the packet loss probability and delay times in the optical packet switched network. The network and node model have been proposed, and the structure of the IP access interface, including assembler and holder, have been included in the analysis. It has been shown that the increase of the maximum optical packet sizes, as well as use of the holding feature as contention resolution mechanism, decrease the packet loss probability, but introduce delays at the optical network access points. Modeling and analysis were based on the discrete event simulation assuming self-similar traffic sources. IP packet lengths were modeled using empirical data. This work has been conducted while the author was affiliated with the Telecommunication Laboratory, Swiss Federal Institute of Technology (EPFL-STI-ITOP-TCOM), Lausanne, Switzerland     

动态交通分配中一类转换率系统的稳定性

在假设交通很拥挤同时交通的转换率与路径费用成正比的前提下，构建了一个动态的转换率模型．为了获取转换率系统的全局渐近稳定，提出了一个普遍适用的Lyapunov函数方法，与此同时通过线性矩阵不等式方法，得到了保证转换率系统全局渐近稳定的充分条件．     

Short cue presentations encourage advance task preparation: A recipe to diminish the residual switch cost.

In the task-switching literature, it has frequently been demonstrated that although advance task preparation reduces the switch cost, it never really eliminates the switch cost. This remaining residual switch cost received much attention, and it has been argued that advance preparation is restricted in nature. In the present study, the role of task-cue presentation in the establishment of the residual switch cost was investigated. In 4 experiments, the cue was removed during the preparation interval, and it was hypothesized that this would encourage participants to complete advance task preparation. The results of all 4 experiments provided support for this hypothesis: When the cue was presented for a short time and then removed, the residual switch cost completely disappeared. This was found for different cue types. Furthermore, Experiment 3 demonstrated that it was not the presence of the cue itself but merely differences in advance task preparation that caused the effects. This suggests that advance task preparation is not as restricted in nature as previously assumed. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Series resonant ZCS‐PFM DC‐DC power converter with high‐frequency high‐voltage transformer link for high‐power magnetron drive

This paper presents a single lossless inductive snubber‐assisted ZCS‐PFM series resonant DC‐DC power converter with a high‐frequency high‐voltage transformer link for industrial‐use high‐power magnetron drive. The current flowing through the active power switches rises gradually at a turned‐on transient state with the aid of a single lossless snubber inductor, and ZCS turn‐on commutation based on overlapping current can be achieved via the wide range pulse frequency modulation control scheme. The high‐frequency high‐voltage transformer primary side resonant current always becomes continuous operation mode, by electromagnetic loose coupling design of the high‐frequency high‐voltage transformer and the magnetizing inductance of the high‐frequency high‐voltage transformer. As a result, this high‐voltage power converter circuit for the magnetron can achieve a complete zero current soft switching under the condition of broad width gate voltage signals. Furthermore, this high‐voltage DC‐DC power converter circuit can regulate the output power from zero to full over audible frequency range via the two resonant frequency circuit design. Its operating performances are evaluated and discussed on the basis of the power loss analysis simulation and the experimental results from a practical point of view. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 153(3): 79–87, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20126     

A novel dynamic RWA algorithm with intelligent granularity regulation in multi-granular all-optical networks

With the great advances of DWDM technology, optical cross-connects have to deal with much more wavelengths. Accordingly, the size of optical cross-connects become larger and larger; also the management cost is much higher. To simplify the architecture of cross-connects for low-complexity maintenance, waveband switching (WBS) in conjunction with several optical cross-connect architectures have been proposed and attracted much attention recently. The main concept of WBS is to group multiple wavelengths into a single waveband and what it concerns includes cross-connect cost and port count reduction. In this paper, we investigate the dynamic RWA problem (MG_DRWA) in WBS networks comprising of all-optical switches based on a cost-effective multi-granular optical cross-connect (MG-OXC) architecture. With this reconfigurable architecture, an optical cross-connect can switch at either fiber level, waveband level, or wavelength level according to its configuration. In order to effectively accommodate dynamic traffic demand, we propose a new MG_DRWA algorithm. Numerical results reveal that the proposed algorithm can achieve significantly better blocking performance as compared to a previously proposed algorithm named MILB under various traffic loads.     

The magnetic applications choice among ferrite ceramics,metallic strips,or metal powder cores

Iron-based metallic strip materials such as iron, silicon-iron, and amorphous metal are used for low frequency (50–60 Hz. line) power applications. Low-loss Nickel-based alloys as high permeability strip or insulated powder cores are the choices for stable, low-level higher frequency applications. Iron-based powder cores offer low cost as power supply filter chokes. Ceramic ferrites combine highest frequency operation with low cost and reduced component size as transformers and chokes in telecommunication and high frequency power supply applications.