机械式有杆泵抽油井示功图的识别

介绍了一种用计算机精确、快速识别机械式示功图的方法。将绘制的示功图通过扫描仪输入计算机,通过对示功图进行二值、细化、矢量化等处理,将示功图的二值点阵信息转换为矢量信息,为后续示功图特征提取创造有利条件,有利于提高抽油井故障的诊断正确率。     

穿透裂纹和表面半椭圆裂纹模型的失效评定曲线比较

针对弹塑性材料裂纹管道的J积分计算建立了等效穿透裂纹和表面半椭圆裂纹2种有限元模型。在等效穿透裂纹模型中应用了1／4节点单元，在表面裂纹模型中采用了线弹簧单元。用这2种模型计算J积分，分别对3个实际含裂纹管段建立了失效评定曲线。比较了2种模型的失效评定曲线和R6通用曲线的差别，指出穿透裂纹模型偏于保守，建议在油气管道断裂的工程评定中采用半椭圆表面裂纹模型。     

The combined effects of curing and environmental exposure on fracture properties of woven carbon/epoxy laminates

This paper concerns a study of the combined effects of curing conditions and environmental exposure on the ultimate properties of two commercial woven carbon/epoxy laminates. Curing parameters (heating rate and applied pressure) were varied so as to obtain six different conditions for each material. Moisture saturation was also achieved by exposing some of the cured samples to environmental conditions of 70°C and 95% relative humidity. Four different tests (tensile, impact, Mode I and Mode II interlaminar fracture resistance) were therefore performed, and the results obtained on the different materials before and after moisture saturation compared. Neither curing pressure nor heating rate nor moisture absorption were observed to have any practical effect on tensile and impact properties. On the contrary, one noticeable effect was the interlaminar fracture resistance of the laminates. The results are discussed and interpreted in terms of damage formation and stress intensification mechanisms.     

SMT互连组件在热循环中的可靠性预计模型

电子设备中表面安装器件和电路基板以及焊接材料的热膨胀系数差异,使得SMT互连组件在热循环条件下产生热膨胀失配,在焊接处产生热应力,在长时间的交变应力的作用下,焊接处遭到疲劳破坏而使设备工作失效,这就是SMT互连组件在热循环条件下的基本失效机理。文中还介绍了美国MIL—HDBK—217F NOTICE Ⅱ公布的表面安装连接组件可靠性预测lSMT模型。给出一系列具有实用价值的参数。     

Rolling contact fatigue behavior of sintered and hardened steels

Powder-metal-processed bearings and gears are finding increasing application because of their economical and technical advantages. The residual pores from the sintering operatives act as lubricant pockets and dampen sound and vibration. However, porosity also decreases the mechanical strength and reduces the life of components fabricated by powder processing relative to similar wrought components. The rolling contact fatigue behavior of sintered and heat treated steel rollers was investigated using a fatigue test machine designed and fabricated for that purpose. The powder-metal-processed and the wrought steel rollers that were tested had similar composition and hardness and were mated against wrought steel rollers of high hardness. The contact stress versus number of cycles to failure data showed that the wrought steel had a very high endurance limit under rolling contact fatigue compared to the sintered steels investigated. Rolling contact fatigue behavior was found to depend on the porosity present in the material. Large surface peeling failures and pitting type fatigue failures were observed in the sintered and hardened steels, while only pitting type failures were observed in the wrought steels     

Effect of crack-growth mechanism on the prediction of fracture load of adhesive joints

This paper presents observations regarding the cracking behavior of tensile-loaded structural adhesive joints. Experiments showed that fracture occurred by the development and propagation of a damage zone, rather than a single, sharp crack, and that the presence of the adhesive spew fillet did not affect the fracture load of the adhesive joints studied. For joints bonded with the mineral-filled epoxy Cybond 4523GB (American Cyanamid), there was approximately 5 mm of subcritical crack propagation prior to final fracture. Fracture-load predictions based on the initial uncracked geometry made in previous papers were unaffected by this small change in geometry. For joints bonded with the rubber-toughened epoxy Permabond ESP 310, approximately 50 mm of subcritical crack propagation was observed. It was again found that predictions made in previous papers on the basis of the initial geometry gave a good estimate of the final fracture load even though this subcritical crack propagation significantly altered the geometry, and thus the applied energy release rates. The effect of shear deformations of the adherends was also investigated, and it was found that shear deformations could be neglected in engineering calculations for joints subject to remote tensile loading.     

大规模集成电路浮栅ROM器件总剂量辐射效应

提出了一种大规模集成电路总剂量效应测试方法:在监测器件和电路功能参数的同时,监测器件功耗电流的变化情况,分析数据错误和器件功耗电流与辐射总剂量的关系.根据该方法利用60Co γ射线进行了浮栅ROM集成电路(AT29C256)总剂量辐照实验,研究了功耗电流和出错数量在不同γ射线剂量率辐照下的总剂量效应,以及参数失效与功能失效时间随辐射剂量率的变化关系,并利用外推实验技术预估了电路在空间低剂量率环境下的失效时间.     

胜利油田污水储罐腐蚀防护方法评价

对胜利油田纯粱采油厂A3钢制生产污水（水温约60℃）储罐使用寿命过低的原因进行了实验考察。水质分析数据表明氯离子浓度高（45-48gm）是污水腐蚀性强的主要因素。A3钢在60℃污水中的腐蚀速率，由极化曲线数据计算的值大大高于失重法测定值，敞开系统中失重法测定值又高于密闭系统中测定值，挂片上出现蚀孔，说明储罐中A3钢发生了氧存在下氟离子引起的局部腐蚀（孔蚀）。元素分析结果表明．储罐阴极保护所用的牺牲阳极铝材含铁等元素量超标。牺牲阳极密封不良，在实验污水中7天后电流效率仅为2．92％，失去阴极保护能力。处于实验污水环境中的有涂层保护的A3钢．14天后出现腐蚀极化电流，表明涂层已失去完整性。要提高该采油厂及胜利油田其他采油厂污水储罐的使用寿命，必须改用合格的牺牲阳极和保护涂层材料。图3表2参7。     

三峡工地高压供电线路故障判断方法的探讨

高压供电设备故障特别是输电线路的高压接地故障对工地的影响是相当大的。由于接地故障为隐性故障，没有明显的物理现象，且若是长期接地可能会发展成较为严重的两相或三相短路故障，使系统解列运行直至崩溃；由于工地流动人员较多，还易造成电击事故。利用高压一相接地时在线路中产生零序电压这一特性来迅速判断和切除接地的用电设备，可以保证各项施工的顺利进行。     

双头螺栓失效分析

与汽车电机装配在一起的双头螺栓在拧紧后不久便发生断裂。采用扫描电镜、化学分析、金相检验等方法对失效件进行了检测，同时又进行了氢脆试验验证。结果表明，螺栓在进行表面酸洗及电镀时，氢向金属内部扩散和富集，当氢浓度达到一定临界值后，促使氢致裂纹的产生和扩展。在外应力的作用下，即出现氢脆现象导致螺栓断裂。