铝合金局部加压凝固及流动数值模拟的研究

局部加压方法是压铸中用于消除铸件厚壁处缩孔缺陷的一种新工艺.本研究通过实验模型测量了不同加压条件下铸件的冷却曲线,分析了局部加压引起的凝固变化.考虑局部加压引起的补缩流动,通过适时修改网格文件、初始和边界条件的方法,模拟了局部加压过程中铝合金的凝固及流动变化,并与实验结果进行了对比,二者基本吻合.     

脲醛呋喃树脂中氮含量的测定

脲醛呋喃树脂中的含氮量,一般采用克氏定氮法,方法繁琐,费时较长,不利于快速分析的要求,本文利用气相色谱法对脲醛呋喃树脂中的氮含量进行分析测定,并建立了测定方法.方法简捷、快速、重现性好,加标回收率在100.8～109.0之间,准确度较高,可很好的满足工业生产中快速分析的要求.     

铈对中铝耐热铸铁抗氧化性能的影响

采用氧化增重法测定了含Ce中铝耐热铸铁在850℃时氧化动力学曲线，用SEM，X－ray对氧化膜表面的形貌，结构及氧化层－基体界面进行了观察分析，结果表明：Ce改变了中铝耐热铸铁氧化膜的结构和组成，提高了中铝耐热铸铁的抗氧化性能。     

退火温度对Ag/Cu层复合板分离强度的作用

对轧制复合的Ag Cu双金属薄板采用不同温度的退火处理 ,研究了结合面分离强度随退火温度变化的规律 ,讨论了影响分离强度的因素。结果表明 ,在 40 0℃以下随退火温度的升高 ,由于原子扩散及再结晶晶界的形成趋于充分而导致分离强度升高 ,40 0℃时分离强度达到最大值。当退火温度超过 40 0℃后 ,由于结合面的异类原子不等量对流而导致结合面形成空洞 ,从而使分离强度下降。 750℃退火时分离强度达到最低值。退火温度进一步上升到 80 0℃时可使结合面发生局部熔合 ,使分离强度又有小幅度回升     

利用新技术开发腾冲硅灰石资源

阐述了用超细硅灰石复合纤维新材料,部分替代植物纤维在造纸业中应用的重要性。介绍了利用新技术开发腾冲硅灰石资源的情况及设计流程。该技术可促使造纸业的良性可持续发展,并保护了宝贵的森林资源及生态环境。     

CYCLIC DEFORMATION OF COARSE GRAINED POLYCRYSTALLINE PURE Al——Ⅱ.FRACTURE SURFACE MORPHOLOGY

SEM photos for very coarse grained and high ductile polycrystalline pure Al show followingcharacteristics:A few fracture sources are concentrated,the crack propagates in fan-shapenear them,and the fatigue striations are cyclic cleavage facets.Each striation consists of awide cleavage facet and a narrow cleavage stage.Those stages often blunt due to plasticdeformation.The fatigue striations are clear and continual,and distribute over whole zone ofstage Ⅱ crack propagation.Two kinds of fatigue striations form in different levels,areconjoined by a“twisted baked piece of pastry”band.The secondary crack along the fatiguestriations was observed frequently.Some of them have already developed into secondarymacrocracks and secondary fatigue striations were found clearly on secondary fracture sur-face.The fracture surface can be divided into two parts,initiation and propagation zone of thecrack,however,no statical-fracture zone was observed.The mechanism to form striationswas preliminarily discussed.     

MICROSTRUCTURE STUDY OF CONSTITUENT PHASES IN 2024 SERIES Al ALLOYS

X-ray microanalysis,convergent beam electron diffraction(CBD)and selected area electrondiffraction(SAD)studies on the structures and compositions of the constituent phases in2024 series Al alloys have been conducted.Partial substitution of alloying elements is found tooccur in all the constituent phases,which cause small deviations from the stoichiometric com-positions reported in these ternary compounds.The dominant phase is α-Al_(12)(FeMn)_3Si whichhas a body center cubic crystal structure with the Im■ space group and a=1.25 nm.The nextdominant phase is Cu_2FeAl_7 which has a primitive tetragonal crystal structure with theP4/mnc space group and a=0.6336 nm,c=1.487 nm.The minor phase is α'-Al_(12)Fe_3Si hav-ing α primitive cubic crystal structure with the Pm■ space group and α=1.27 nm.     

高铬铸铁-碳钢复合板水平浇注铸造工艺

研究了厚度为40 mm高铬铸铁-碳钢复合板水平浇注铸造工艺,并对二者复合强度进行了检测.结果表明:当先浇注的定量高铬铸铁冷却到1080～1220℃时在其上再浇注碳钢均可获得牢靠的复合铸件.     

Si/C比对灰铸铁组织和性能的影响

综述了Si/C比对高强度灰铸铁的石墨形态、奥氏体数量和铸件表层铁素体等显微组织以段对铸铁件的力学性能和铸造性能的影响，     

Preparation and hydrogen sorption properties of Mg-Cu-Y-H systems

Mg-xwt.%CuY (x=15, 20, 25) composites were successfully prepared by reactive mechanical alloying (RMA).X-ray diffraction (XRD) measurement shows that main phases of the as milled composites are MgH2 and Mg2Cu, and they converted into Mg and MgCu2 after dehydrogenation, respectively.Pressure-Composition-Isotherm (PCI) test shows that the composites exhibit double pressure plateau at each isothermal desorption process.The hydrogen absorption and desorption kinetics of the composites become worse with increasing x content, indicating that Mg-Cu phase has a negative effect on the hydrogen sorption properties of the composites.It is supposed that the good hydrogen sorption properties of the composites attribute to the catalyst effect of yttrium hydride distributed in Mg substrate and the particles size reduction and crystal defects formed by RMA.