双电池系统电源选择器MAX1773/1773A

MAX1773／MAX1773A是用于双电池系统的电源选择器，它允许外部控制器去管理双电池组、适配器输入、电池充电器和系统负载所需的电源连接。文中介绍了MAX1773／1773A的特点、引脚功能、内部结构和工作原理，给出了MAX1773/MAX1773A的典型工作电路。     

草酸钙在硫酸软骨素自组装膜上周期沉淀的研究

利用硫酸软骨素(chondroitin sulfate，CS)在云母基底上通过浇铸法制备的自组装膜为基底，诱导草酸钙在其上的凝集生长。发现当硫酸软骨素的浓度为1．Omg／ml时在该膜体系中可形成规整的周期性草酸钙环状沉淀。这种有序的环状结构可能是耗散结构的一种具体表现形式。利用原子力显微镜(atomic forcemicroscope，AFM)和傅立叶红外光谱仪对这种结构进行了表征，实验结果显示合适浓度下形成的CS膜在一定程度上可以抑制草酸钙的凝集结晶，表明高分子基质与无机离子间强烈的相互作用对无机盐的成核结晶有显著影响，为探讨结石的形成与抑制提供了一定的实验依据。     

Synchronous Full-Scan for Asynchronous Handshake Circuits

Handshake circuits form a special class of asynchronous circuits that has enabled the industrial exploitation of the asynchronous potential such as low power, low electromagnetic emission, and increased cryptographic security. In this paper we present a test solution for handshake circuits that brings synchronous test-quality to asynchronous circuits. We add a synchronous mode of operation to handshake circuits that allows full controllability and observability during test. This technique is demonstrated on some industrial examples and gives over 99% stuck-at fault coverage, using test-pattern generators developed for synchronous circuits. The paper describes how such a full-scan mode can be achieved, including an approach to minimize the number of dummy latches in case latches are used in the data path of the handshake circuit.     

Physico-chemical characterization of hybrid polymers obtained by 2-hydroxyethyl(methacrylate) and alkoxides of zirconium

Hybrid monolithic materials were prepared through polymerisation of 2-hydroxyethyl methacrylate (HEMA) mixed with zirconium alkoxides (Zr(OBuⁿ)₄, Zr(OPrⁿ)₄ and Zr(OEt)₄), modified by acetylacetonate groups. The molar ratio HEMA/Zr varied between 1 and 4. Thermo-Gravimetry coupled with Mass Spectroscopy (TG-MS) analyses, ¹³C MAS NMR and Dynamical Mechanical Thermal Analysys (DMTA) indicated the polymeric chains were interconnected by the inorganic component.The presence of zirconium alkoxides modified substantially the poly-HEMA properties. Glass transition temperature of hybrid materials derived from butoxy and propoxy was found in the range 50-80 °C, depending on the composition. The typical swelling of p-HEMA in the water, was suppressed by the presence of zirconium compounds. After immersion in distilled water, hybrid polymers showed an initial slight weight increase, followed by a small mass loss, which increases proportionally to the length of alkoxyl group (ethoxide(propoxide(butoxide) and reaches a constant value after about 40 days. The hybrids remained always rigid and transparent. Flexural modulus and strength of about 400-900 and 4-8 MPa were measured.     

Wear and Creep Characteristics of a Carbon‐Derived Si3N4/SiC Micro/Nanocomposite

In the presented work some properties of a recently developed Si₃N₄/SiC micro/nanocomposite have been investigated. The material was tested using a pin on disc configuration. Under unlubricated sliding conditions using Si₃N₄ pin at 50 % humidity, the friction coefficient was in the range of 0,6 ‐ 0,7. The reduction of humidity resulted in a lower coefficient of friction, in vacuum the coefficient of friction had a value of about 0,6. The wear resistance in vacuum was significantly lower then that in air. The wear patterns on the Si₃N₄+SiC disc revealed that mechanical fracture was the wear controlling mechanism. Creep tests were realized in four point bending configuration in the temperature interval 1200‐1400 °C at stresses 50,100 and 150 MPa and the minimal creep deformation rate was established for each stress level. The activation energy, established from the minimal creep deformation had a value of about 360 kJ/mol and the stress exponent values were in the range of 0.8‐1.28. From the achieved stress exponents it can be assumed that under the studied load/temperature conditions the diffusion creep was the most probable creep controlling mechanism.     

Inhibition effect of carbon dioxide on the oxidation of hydrogen over a platinum foil catalyst

This paper investigates the catalytic ignition of the H₂/O₂/CO₂ mixture on platinum in a stagnation flow at atmospheric pressure experimentally and numerically. We measure the ignition temperatures of the gas mixtures flowing towards resistively heated platinum with various composition ratios and various diluent gases of N₂, Ar and CO₂. Compared with N₂ or Ar, the CO₂ dilution shows higher ignition temperature by about 50 K, even at the same composition ratio. The ignition temperature increase is proportional to the dilution ratio. Through the numerical simulation, it is illustrated that higher ignition temperature is caused by the adsorption of CO₂ and following dissociation on platinum surface, which was to date considered negligible in catalytic combustion.     

GPRS手机入网测试自动化

全球移动通信系统(GSM)广泛的应用于现代通信系统就在于其良好的兼容性,不同的移动设备之间在遵守一定协议规范的条件下可以相互通信;本设计测试的是GSM第11系列GSM11.10,他包括诸多测试项,只对接收机参考灵敏度电平在GSM900与DCS1800两个频段进行测量。给出了传统形式下的手动测试和自动测试平台的比较,并建立了收信机参考灵敏度指标的自动测试平台。     

凝胶成型法制备加氢催化剂载体的研究与工业化生产

采用凝胶成型法制备加氢催化剂载体，并进行了工业放大试验。通过BET、NH3-TPD、H2-TPR等表征手段及实际的加氢反应性能评价对凝胶成型法制备的载体及加氢催化剂与常规方法进行对比分析，结果表明，采用凝胶成型法所制得的载体及催化剂均具有较高的孔体积和比表面积、较低的堆密度，其机械强度可满足工业要求，总酸量及中强酸酸量得到提升，催化剂活性组分与载体强结合力得到削弱，金属利用率提高，应用性能明显优于传统方法制备的加氢催化剂载体。通过该方法完成了加氢催化剂载体的工业生产，所生产的载体应用于天津院THDS-3加氢精制催化剂取得了良好的工业应用效果。     

DS/FH通信系统的跳频同步技术研究

同步是DS/FH混合通信系统的关键技术之一。根据跳频系统中对同步的要求,介绍了一种适用于DS/FH混合扩频通信系统的跳频同步方法,采用同步字头和精准时间相结合的方法实现跳频同步。对同步性能进行了分析,结果表明该跳频同步方法同步时间短,捕获概率高。     

Finite element piezothermoelasticity analysis and the active control of FGM plates with integrated piezoelectric sensors and actuators

 An efficient finite element model is presented for the static and dynamic piezothermoelastic analysis and control of FGM plates under temperature gradient environments using integrated piezoelectric sensor/actuator layers. The properties of an FGM plate are functionally graded in the thickness direction according to a volume fraction power law distribution. A constant displacement-cum-velocity feedback control algorithm that couples the direct and inverse piezoelectric effects is applied to provide active feedback control of the integrated FGM plate in a closed loop system. Numerical results for the static and dynamic control are presented for the FGM plate, which consists of zirconia and aluminum. The effects of the constituent volume fractions and the influence of feedback control gain on the static and dynamic responses of the FGM plates are examined. Received: 13 March 2002 / Accepted: 5 March 2003 The work described in this paper was supported by a grant awarded by the Research Grants Council of the Hong Kong Special Administrative Region, China (Project No. CityU 1024/01E).