氧化物共还原制取W-Cu和Mo-Cu复合材料的研究

近些年来,国内外研究了一些制备高分散度W/Cu和Mo/Cu复合粉末的方法,高分散度的粉末具有高的烧结致密度,用氧化物共还原粉末可在较低温度下进行烧结得到接近和达到100%的理论密度。这样的复合材料有细而均匀的组织和较好的性能。本文报道近来的研究状况,并就共还原法所用的前驱体原料种类、工艺条件、粉末特性和复合材料的性能进行评述。     

Buckling optimization of hybrid-fiber multilayer-sandwich cylindrical shells under external lateral pressure

This paper describes a method of analyzing the maximum buckling strength of hybrid-fiber multilayer-sandwich cylindrical shells under external lateral pressure with respect to fiber orientations and weighting factors. Formulae for optimizing these parameters are presented and conditions for the application of these formulae are discussed. A discriminant is derived for assessing whether the hybrid sandwich cylindrical shells for given different unidirectional composites should reach the extreme value of critical pressure.     

电流变体特性及电流变体应用器件的进展

本文详细评述了电流变体(ERF)材料的组成、工作机理及其流变力学性能,提出以Bingham塑性体来近似描述电流变体的流变特性,综述了电流变体在智能材料、汽车离合器、液压阀门等器件中的应用,给出了含电流变体的双层智能复合材料梁单层、双层加电状态对其振动特性的影响,设计了含电流变体的主动控制式减振器,并对其在外加电场作用下的减振性能进行了评价。     

锌基复合材料研究进展

评述了锌基复合材料的发展和研究概况,着重介绍了锌基复合材料的制备工艺和性能研究现状,最后对锌基复合材料的研究方向和应用前景提出了一些设想和展望。     

不连续增强镁基复合材料的界面行为

综述了近年来国内外关于Ａｌ２Ｏ３短纤维、ＳｉＣ晶须、ＳｉＣ颗粒、Ｂ４Ｃ颗粒增强镁基复合材料的界面结构及其对复合材料性能影响的研究进展，并对今后的研究提出了一些看法。     

颗粒增强TiAl基复合材料及其Si的韧化作用研究EI

运用ＸＤ工艺制备了颗粒增强ＴｉＡｌ基复合材料。增强颗粒均匀分布于ＴｉＡｌ基体中并细化ＴｉＡｌ合金。通过在ＴｉＢ_２／ＴｉＡｌ、ＴｉＣ／ＴｉＡｌ复合材料中加入适量的Ｓｉ，颗粒增强ＴｉＡｌ基复合材料的室温延性得到了改善。     

Development of damage in a 2D woven C/SiC composite under mechanical loading: I. Mechanical characterization

An investigation has been undertaken to determine the damage mechanisms and the associated mechanical response of a 2D reinforced composite of carbon fibers in an SiC CVI-processed matrix subjected to uniaxial tensile and compressive loadings at room temperature. Under tension loading, an extended non-linear stress/strain response was evidenced and related to a multi-stage development of damage involving transverse matrix microcracking, bundle/matrix and inter-bundle debonding as well as thermal residual stress release. This tensile behavior proved to be damageable-elastic with respect to a fictitious thermalstress-free origin of the stress/strain axis lying in the compression domain. In compression, after an initial stage involving closure of the thermal microcracks present from processing, the composite displayed a linear-elastic behavior until failure. The extent of damage over the material was characterized quantitatively at the microscale by the decrease of the average transverse microcrack spacing and at the macroscale by the decrease of both the longitudinal Young's modulus and the in-plane Poisson's ratio.     

矩形橡胶复合材料层合板几何非线性分析

文中应用简单高阶剪切层合理论和大变形理论对各向异性纤维增强的矩形橡胶复合材料层合板进行了几何非线性分析.与线性理论相比,本文作者进行的层合板大变形状态的几何非线性分析和所计算的层板应力分布,更具有准确性.     

Surface treatment for adhesive-bonded joints by excimer laser

In this work a treatment for surface preparation to improve mechanical resistance in adhesive bonding of plastic composites reinforced with fibres and metallic material, has been performed using an excimer laser. The following couplings have been selected to reproduce joints commonly used in the aerospace and automotive industry: CFC (carbon fibre composite) with CFC, CFC with Al 2024T3, Al 99% with Al 99%, GFC (glass fibre composite) with zinc-coated sheet in low carbon steel FeP01. The surfaces have been prepared using an excimer laser, adopting several values of laser parameters. The obtained surfaces have been examined by optical and scanning electron microscope: comparative measures of wetting and roughness have been performed to obtain an accurate characterisation and to select the proper finishes suitable to improve the mechanical resistance of the joints. The results obtained show that laser treatment always improves the final resistance of the joint; notable increases, and no significant surface damages have been highlighted. Better results have been obtained with the Al 99% with Al 99% joints which, with a low number of pulses treatment, have shown an increase of mechanical resistance up to the 70%.